Table of Contents
Summary of Contents for Wachs TL 2.0
- Page 1 TUBE LATHE MODEL TL 2.0 & TL 4.0 21-000-02, 04, 22, 24 PIPE & TUBE CUT-OFF MACHINES Mod. TL 2.0, 4.0 S/N: E.H. WACHS COMPANIES 100 Shepard St. Wheeling Il. 60090 Patent Pending Part Number: 21-MAN-00 Revised: Revision No: Jan. ‘98...
-
Page 2: Table Of Contents
TUBE LATHE TABLE OF CONTENTS SECTION I STANDARD EQUIPMENT..................5 SECTION II SAFETY INSTRUCTIONS..................6-9 SECTION III EC DECLARATION OF CONFORMITY..............10 SECTION IV MACHINE SPECIFICATIONS................11 SECTION V SET UP AND OPERATING PROCEDURES..........12-15 Tube Lathe Components A. Assembly of machine from case B. Clamp Shoe selection and installation C. -
Page 3: Section I
TUBE LATHE STANDARD EQUIPMENT SECTION I 21-000-02 Wachs Model TL 2.0 Portable Tube Cut-Off Lathe for 1/4” to 2” (6.35-50.8 mm) diameter, complete with split- type rotating and stationary frames, adjustable sealed bearing system, starwheel feed radial tool slide, Metabo 110v 50 hz/60hz electric drive motor, bench stand, custom fitted storage case, operating hand tools and manual. -
Page 4: Safety Instructions
TUBE LATHE SAFETY INSTRUCTIONS SECTION II The E. H. Wachs Company takes great pride in manu- For your safety and the safety of others, read and facturing safe, quality products with user safety a understand these safety recommendations and op- priority. - Page 5 Seit 1883 hat EH Wachs seinen Ruf für Qualität und Zufriedenstellung seiner Kunden aufgebaut. Wachs übernimmt demgemäß die Depuis 1883, la société EH Wachs a bâti sa réputation sur la qualité de ses produits et son engagement à satisfaire la clientèle.
- Page 6 INSTRUÇÕES DE SEGURANÇA TURVALLISUUSOHJEET Já desde 1883 que a EH Wachs tem vindo a criar uma reputação de qualidade e um compromisso de satisfação dos EH Wachs on tunnettu korkeasta laadusta ja tyytyväisistä asiakkaistaan jo vuodesta 1883. Wachs huolehtii myös siitä, että...
- Page 7 ANVISNING I SIKKERHED Siden 1883 har EH Wachs haft ry for deres kvalitet og varetagelse af kundtilfredshed og vil også gøre vort bedste for at sikre, at vore maskiner benyttes på en sikker og forsvarlig måde. Vi har lavet en liste over påmindelser, der skal bidrage til at skabe det sikrest mulige arbejdsmiljø. Vi anbefaler, at sikkerhedsforanstaltningerne på...
-
Page 8: Ec Declaration Of Conformity
EN 292-2, EN 294, EN 394 PR: EN 982, PR: EN 983 10/95 PR: EN Other Safety Standards Used: 792-1, PR: EN 1050 Name of person authorized to sign on behalf of the E.H. Wachs Companies: Rodger P. Soeldner Vice President/CFO Position: Signature:... -
Page 9: Machine Specifications
TL 4.0: .002” (.00508 mm)/revolution Drive Motor: Metabo 110v or 220v Weight: TL 2.0: 18 lbs (8.13 kg); TL 4.0: 24 lbs (12.48 kg) Finish: Corrosion reistant plating MACHINE NOISE LEVELS: NOTE: NOISE LEVELS HAVE BEEN MEASURED AT 1 METER HIGH AND 1.6 METERS AWAY. -
Page 10: Set Up And Operating Procedures
TUBE LATHE SET-UP AND OPERATION SECTION V Tube Lathe Components (all models) A. Clamping Handle I. Tool Bit B. Retaining Pin J. Allen Wrench C. Star Wheel K. Stationary Frame D. Tool Slide Assembly L. Rotating Frame E. Clamp Shoe M. -
Page 11: Assembly Of Machine From Case
TUBE LATHE SET-UP AND OPERATION (cont.) SECTION V Assembly of machine from case Workpiece Clamping 1. Remove Tube Lathe, Drive Motor and Bench Plate 1. Open Clamp Shoes by rotating Clamping Handle. from storage case. 2. Place workpiece into machine. 2. -
Page 12: Tool Bit Installation
TUBE LATHE SET-UP AND OPERATION (cont.) SECTION V FIGURE 3 FIGURE 5 Tool Bit Installation 2. Slide Trip Handle inward to engage Starwheel Feed 1. Follow steps 1-3 in section “E” to bring Tool Slide to System on the Tool Slide. To pause cutting opration, its uppermost position. -
Page 13: Drive Motor Speed Settings
TUBE LATHE SET-UP AND OPERATION (cont.) SECTION V Drive Motor Speed Settings CAUTION: Always start the motor with the speed controller on its slow- est speed setting. Speed Settings-TL 2.0 Tube Diameter Speed Dial Setting 1/4” 3/8” 1/2” 3/4” 1-1/2”... -
Page 14: Maintenance
This adjustment should be performed only Gib Tensioning Procedure: by an authorized Wachs Service Technician. Contact the factory or your local Wachs Representative for fur- 1. Adjust Gib by removing the two SHCS on the Lead- ther assistance. -
Page 15: Miscellaneous Charts And Graphs
TL 4.0 Shoe Set for 4” O.D. NOTE: For non-standard sizes, contact the factory for availability. CONSUMABLE SELECTION CHART SECTION VIII PART No. DESCRIPTION 21-700-01 Double sided 1/16” wide parting tool bit for TL 2.0 and TL 4.0. Zinconium Nitrate coated. -
Page 16: Trouble Shooting
TUBE LATHE TROUBLE SHOOTING SECTION IX Trouble Possible Cause Remedy Machine won’t run. Power cord not connected. Check power cord. Workpiece shifts during Loose Shoe Clamp. Check tension on cuttind operation. Shoe Clamp Handle. Poor end quality. Dull or damaged Tool Bit. Replace Tool Bit. - Page 17 TUBE LATHE SECTION X PARTS LISTS & EXPLODED VIEW DRAWINGS...
-
Page 18: Parts Lists And Exploded Views
TUBE LATHE BILL OF MATERIALS TL 2.0 21-000-02, 21-000-22 Ref. # Part # Qty. Description 21-100-02 FRAME, 2" STATIONARY 21-101-02 RING, ROTATING - 2" 52-113-00 BOLT, CAPTIVATED 21-006-01 SHAFT, ECCENTRIC 43-006-00 BEARING,GUIDE WHEEL* 90-045-01 NUT,10-32 JAM 90-055-54 WASHER,AN 1/4 90-055-02... - Page 20 TUBE LATHE BILL OF MATERIALS TL 4.0 21-000-04, 21-000-24 Ref. # Part # Qty. Description 21-100-04 MCH FRAME, 4" STATIONARY 21-101-04 MCH RING, ROTATING - 4" 52-113-00 BOLT, CAPTIVATED 21-006-01 SHAFT, ECCENTRIC 43-006-00 BEARING,GUIDE WHEEL* 90-045-01 NUT,10-32 JAM 90-055-54 WASHER,AN 1/4 90-055-02 HEX NUT,1/4-28 21-021-00...
-
Page 22: Ordering Information
All repair work done at our plant will be estimated and the customer advised of cost and time required to complete repair. WARRANTY INFORMATION Enclosed with the manual is a warranty card. Please fill out the registration card and return to E.H. Wachs. Retain the owners registration record and warranty card for your information. RETURN GOODS ADDRESS E.H.