Advertisement
3 Using the chip card reader
3.1 Reading of chip cards with contact
(TC 1100, TC 1300)
• Insert the chip card into the chip card slot with the
chip facing upwards and towards the read head in
the chip card shaft.
After a discernable pressure point has been passed,
contact takes place.
3.2 Reading of non-contact chip cards/
transponders (TC 1200, TC 1300)
• Position the chip card or transponder as parallel to
the chip card reader as possible. (You can also
insert the card into the chip card reader.)
Data is transmitted beginning at a distance of less
than 5 cm.
3.3 Fitting chip card holder (TC 1200,
TC 1300)
• Press the chip card holder from above onto the
cable reinforcement on the casing, until you feel it
click into place.
The holder is not designed to be repeatedly attached
and detached.
4 LED-Status
4.1 TC 1100
LED
Status
Steady blue
Terminal ready
Blue light flashes once,
Card inserted
then steady blue
Flashing blue
Data transmission
Off
Terminal in energy-saving
mode (if activated)
4.2 TC 1200
LED
Status
Steady white
Terminal ready
Blue light flashes once,
Card/transponder is seated
then steady white
Flashing blue
Data transmission
4.3 TC 1300
LED
Status
Steady green
Terminal ready
Red light flashes once,
The card is inserted or the
then steady green
card/transponder is seated
Flashing red
Data transmission
5 Technical data
Designation
Value
Supply voltage
+5 V/DC ±5 % SELV
Current consumption TC 1100: max. 30 mA
TC 1200: max. 230 mA
TC 1300: max. 160 mA
Storage temperature
–20 °C ... +65 °C
Operating temperature 0 °C ... +50 °C
Dimensions
TC 1100: 100 x 65 x 12 mm
TC 1200: 76 x 62 x 11 mm
TC 1300: 115 x 75 x 16.5 mm
Card reading unit
100 000 insertions
Protocols
TC 1100: T=0, T=1, S=8, S=9,
S=10
TC 1200: T=CL
TC 1300: T=CL,T=0, T=1
2
6 Disposing
Dispose of the old unit via a collecting point
for electronic scrap or via your dealer.
7 Contact
Please provide the following information about the
device when you make an inquiry:
• Item and serial no. of the product
• Name and manufacturer of your system
• Operating system and, if applicable, installed
service pack version
ZF Friedrichshafen AG, Electronic Systems
Cherrystraße
91275 Auerbach, Germany
Internet: www.cherry-world.com
E-mail: info@cherry.de
8 General advice
We reserve the right to make technical modifications
which serve the development of our products.
Improper use and storage can lead to faults and
damage to the product.
The warranty expires completely once unauthorized
modifications to the product have been carried out. Do
not carry out any unauthorized repairs and do not
open up the product. These instructions are only valid
for the supplied product.
9 Warranty
The statutory warranty applies. You can find more
information on the warranty under
www.cherry-world.com.
10 Warning note
CAUTION: Danger of suffocation due to
swallowing of small parts
• Ensure that this unit does not end up in the hands
of children under the age of six.
11 Certifications
11.1 For UL
For use with Listed Personal Computers only!
11.2 Federal Communications
Commission (FCC) Radio
Frequency Interference
Statement
Information to the user: This equipment has been
tested and found to comply with the limits for Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
• Reorientate or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Caution: Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
11.3 CE Declaration of Conformity
(TC 1200, TC 1300)
Hereby, ZF Friedrichshafen AG, Electronic
Systems business area, Auerbach/Opf.,
Germany, declares that this Radio-
Frequency peripheral is in compliance with the
essential requirements and other relevant provisions
of Directive 1999/5/EC. The CE Declaration of
Conformity can be retrieved by accessing the
following internet address: www.cherry.de/
compliance.
Once accessed, click on the relevant product name to
retrieve the CE Declaration of Conformity.
FR
Mode d'emploi
1 Avantages
• SmartTerminal pour le traitement de cartes à puce
selon ISO 7816 (TC 1100, TC 1300) et de cartes à
puce sans contact selon ISO 14443/15693 (TC 1200,
TC 1300)
• Homologation EMVCo, EMV 2000 Level 1 contact
approved interface (TC 1100, TC 1300)
Avec le logiciel d'application correspondant, vous
pouvez utiliser le SmartTerminal pour les tâches sui-
vantes:
• Paiement via l'internet (Internet Payment)
• Signature numérique
• Public Key Infrastructure (signature numérique au
niveau de l'entreprise ou entre firmes)
• E-commerce
• Home Banking
• Contrôle d'accès (Access Control)
• Cryptage de données
2 Raccordement au PC et
installation du logiciel
1 Téléchargez le pilote actuel sur notre site
www.cherry-world.com à la rubrique
Service & Support/Downloads.
2 Suivez les instructions d'installation à l'écran.
3 Connectez la fiche USB du SmartTerminal au
connecteur USB de votre PC.
3 Utilisation du lecteur de cartes
à puce
3.1 Cartes à puce à contact (TC 1100,
TC 1300)
• Insérez la carte à puce dans la fente du lecteur
prévue à cet effet, la puce dirigée vers le haut du
côté tête de lecture.
Le contact ne peut avoir lieu que si la carte a été
entièrement insérée. Si une résistance apparaît, il
peut être nécessaire de forcer légèrement.
3.2 Cartes à puce sans contact/
transpondeurs (TC 1200, TC 1300)
• Placez la carte à puce ou le transpondeur si pos-
sible de façon parallèle sur le lecteur de cartes à
puce. (Vous pouvez aussi introduire la carte dans le
lecteur.)
Les données seront transmises à partir d'une dis-
tance inférieure à 5 cm.
Advertisement
