Advertisement
Quick Links
FV_Rover_Jaguar_MixCAM
installation manual v121202
[Product type: FV_Rover_Jaguar_MixCam]
This interface can insert High definition RGB navigation video, AV and
reverse camera video onto Rover Jaguar cars, including discovery4,Evoque,
Jaguar even including the Dual‐view[the driver sees the navi, while
passenger sees the DVD] Jaguar and Evoque car screens. This interface is
updated from previous version by increasing to the compatibility with so
many screens, and it can show reverse video together with the OEM PDC
together.
The features are:
Daughter board is used to switch the video,so whatever the status is(Radio,
Navi,or factory display mode), the inserted video can be switched. Which is more accepted by reverse camera installation.
OEM keys are used to control and switch the installed anvi and DVD. Reverse
camera trigger signal is automatically generated by can bus, the PDC is displayed
together with reverse video.
Guaranteed digital video quality on screen by LVDS conversion, the improved
compatibility has been verified to work with all Rover and Jaguar car screens
since 2011, including 7‐inch, 8‐inch or dual view.
1．System connection
The 4P touch panel connector should also go
through the daughter board thus touch is given to
the installed navi as well.
The CAN box which has OEM plug and socket can be inserted
on the OEM power plug behind monitor, it can generate ACC,
reverse trigger signal[big current with 12V which is also ok to
supply a camera], and MMI control signals to interface.
1 / 5
The daughter board is installed on the ribbon
connecting the 2 big PCBs inside. 3 screws are used to
fix it there.
3 keys for
color tuning.
NAVI AV1,AV2 Rearview
Advertisement
Summary of Contents for ECVV FV Rover Jaguar MixCAM
- Page 1 FV_Rover_Jaguar_MixCAM installation manual v121202 [Product type: FV_Rover_Jaguar_MixCam] This interface can insert High definition RGB navigation video, AV and reverse camera video onto Rover Jaguar cars, including discovery4,Evoque, Jaguar even including the Dual‐view[the driver sees the navi, while passenger sees the DVD] Jaguar and Evoque car screens. This interface is updated from previous version by increasing to the compatibility with so many screens, and it can show reverse video together with the OEM PDC ...
- Page 2 The signal definition of 6P on interface from CAN box： Yellow：constant power of 12V。 black：GND of chassis。 RED[ACC]：when the monitor works, this wire=12V，otherwise=0V。 Green：reverse signal wire[=12V when in reverse], it can be used: To give reverse signal to interface box，also giving power to camera[max.1A] When giving power to camera, a 100u capacitor is necessary on this wire to filter the noise on camera long wires. When only give reverse signal to interface, and camera is powered elsewhere, do not add capacitor。 White wire：switch signal wire, when =12V or 5V, this interface switches. Gray wire：CAN bus control data to interface, it is used to pop up the control icons. See note2 on the end of this wire. 2. DIP switch setting: DIP ...
- Page 3 The OEM PDC obstacle picture will be displayed together with reverse video when DIP8=DOWN. The “PDC offset” option will make it centered on the right 1/4 screen. When picture is shown like this, the installer needs to do: Check DIP7=Up(8‐inch) or Down(7‐inch), wrong settings will make the picture has big shift in Horizontal and vertical direction. Change the “POSITION H” value, so the left side of picture will be display according to screen left edge. Change the “PDC offset” value to move the PDC obstacle show centered. The DIP8 should be set to DOWN=enable PDC obstacle show in reverse. ...
- Page 4 The installer does not need to wire another trigger signal for reverse. The CAN box will deliver a 12V volt on the green wire, which is used to trigger the interface also power up a camera.[max 1A]. the gray wire will carry the guide line value to the interface. touch to external NAVI： All rover/Jaguar cars has an OEM touch panel on display, which can be switched automatically to external navi。 ...
- Page 5 Parameters No. name parameter 1 RGB video amplitude 0.7Vpp with 75 ohm impedance NTSC resolution [400X240,480X240] of navigation is allowed. Also HD navi: 800X480,640X480 is allowed. 2 sync amplitude in RGB‐navi port 3~5Vpp with 5K ohm impedance Sync should be NTSC composite with negative polarity. 3 Av1,Av2, cam video amplitude 0.7Vpp with 75 ohm impedance 4 Av1,Av2, cam standard NTSC/PAL/SECAM automatic switch 5 6 Normal work Power consumption 2.4W [0.2A @12V] 7 Standby current < 5mA 8 Standby start 10 seconds after the users switch off the CD unit. 9 Reverse trigger threshold >5V trigger 10 Work temperature ‐40 ~ +85C 11 ...