Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for FlySky FS-CT6 (A/B)
- Page 1 FlySky FS-CT6 (A/B) User Manual for Airplane ...
- Page 2 The information covered in this manual is for both versions of the T6, the T6A and T6B. The T6 is manufactured by FlySky and is rebranded for other retailers. It can be found under the following brands HobbyKing, Exceed RC, Turborix, Radiolink, etc...
- Page 3 Open T6config, power on your Tx, and select the COM port you assigned to the USB cable (see illustration 1). Now you should see the channel bars moving as you manipulate the Tx sticks. If the channel bars do not respond to stick movement then double check the steps above.
- Page 4 Illustration 2: Saving your settings in T6config Once you have saved your default setting you can start programming the Tx for your model. The first step will be to select the Tx mode you will be using. You have a choice of Mode 1, Mode 2, Mode 3, and Mode 4 (see illustration 3).
- Page 5 Illustration 3: T6 Mode Selection window Illustration 4: Open window...
- Page 6 To load a saved model to the T6 click “Open”. In the Open window select the desired saved model file and click “Open”(see illustration 4). If the Tx is already connected to T6config the file is automatically uploaded to the Tx. ...
- Page 7 Controls The T6 channel arrangement is: CH 1 ailerons CH 2 elevator CH 3 throttle CH 4 rudder CH 5 aux CH 6 aux The T6 has 2 switches on either side of the carry handle. They are designated SW.
- Page 8 Programming Mixes To program a mix click the “MIX” button. A small window will open (see illustration 6). The parameters for mixing are: 1. Mix Number: MIX 1, MIX 2, and MIX 3 2. Source: CH 1- CH 6, VR A, and VR B 3.
- Page 9 End Point To program end points click the “End Point” button. A small window will open that will allow adjustment of the channel end points (see illustration 7). These can be adjusted from 0-120%. This can be useful when you need extra travel of the servos. ...
- Page 10 Reverse To Program servo reversing click the “Reverse” button. In the reverse window reversing for each channel is performed by placing a check on the channel that needs to be reversed (see illustration 8). ...
- Page 11 Subtrim To adjust the subtrim of the Tx, click the “Subtrim” button. In the subtrim window adjustments can be made for variations in your models trim while leaving the trim tabs centered on the Tx (see illustration 9). This is easily performed after you have your model trimmed for flight.
- Page 12 DR (Dual Rates) Dual rates can be programmed by clicking the “DR” button. In the DR window only CH1, CH 2, and CH 4, can be programmed with dual rates (see illustration 10). There are parameters for DR On and DR Off. The parameters can be set from 0% - 100%.
- Page 13 T6 Programs 2 Servo Ailerons MIX 1 (or any unused mix) Source: CH 1 Des: CH 5 (or CH 6) Up Rate: 100% Down Rate: 100% Switch: On Flaps ...
- Page 14 MIX 2 (or any unused mix) Source: CH 2 Des: CH 1 Up Rate: -100% Down Rate: -100% Switch: On V-tail MIX 1 (or any unused mix) Source: CH 2 Des: CH 4 Up Rate: 100% Down Rate: 100% Switch: On ...
- Page 15 MIX 2 Source: VR A (or VR B) Des: CH 1 Up Rate: 75% Down Rate: 75% Switch: SW A (or SW B) MIX 3 Source: VR A (or VR B) Des: CH 5 (or CH 6) Up Rate: -75% Down Rate: -75% Switch: SW A (or SW B) ...
- Page 16 Bind Procedure The procedure for binding the Rx to the Tx is as follows: 1. Insert the bind plug into the “Batt” port of the Rx. 2. Apply 4.5-6V power to Rx (LED will blink) 3.
- Page 17 T6's together. The USB cable that is included with some brands of T6 radios will not function as a simulator cable without using special programs. FlySky does manufacture and sell a simulator cable for the T6, part # (FS-SM100). It works well with FMS without any special drivers or programs.
- Page 18 R6B does not. Illustration 13: R6B "B" model Illustration 12: R6A "A" model receiver, HK V2 receiver, HK V1 w/satellite Rx Here is a link to the manufacturer: http://www.flysky-cn.com/eindex.asp ...