Table of Contents
Advertisement
SPECIAL PLAYBACK
TO VISUALLY SEARCH FOR DESIRED
POINTS
When either the FF or REW button is pressed in the
PLAYBACK mode, the speed search picture will appear.
When pressed twice, the search picture will increase
speed. Speed search time depends upon the speed
used (SP, LP or SLP) during recording. See chart below.
To visually search backward or forward, press the REW
or FF button once or twice in the PLAYBACK mode.
Press the PLAY button to resume normal viewing speed.
SPEED SEARCH TIMES
TAPE SPEED
SP (Standard Play)
LP (Long Play)
SLP (Super Long Play)
CM SKIP
Press the CM SKIP button in the PLAY mode. The VCR will
search forward through approximately 30 seconds of the tape
(e.g. unwanted commercial time) for each press of the CM SKIP
button (maximum six presses) and then resume normal playback.
TO WATCH STILL PICTURE
Press the PAUSE/STILL button in the PLAYBACK mode.
Press the PLAY button or PAUSE/STILL button to resume
normal playback.
•
NOTES:
The audio output is muted during Speed
Search and Still.
•
A few noise bars will appear on the TV screen
during Speed Search and Still.
•
To prevent damage to the tape, Still and Speed
Search mode is automatically changed to the
Playback mode after 5 minutes.
TO WATCH A TAPE REPEATEDLY
1
Press the MENU button.
2
Press the SET/TRACKING + or
– button to select the AUTO
REPEAT option.
3
Press the ENTER button to select
the ON position.
4
Press the MENU button. If you press the PLAY button,
the tape will play over and over until the repeat mode is
canceled.
NOTE: To cancel repeat mode, follow above steps 1 and
2, then press the ENTER button to select the OFF
position. Press the MENU button to return to the
TV. The repeat function is canceled automatically
when the unit is switched off or the tape is ejected.
PICTURE SEARCH SPEED
PRESS ONCE
PRESS ONCE
PRESS TWICE
PRESS TWICE
3 X
5 X
7 X
9 X
9 X
15 X
M E N U
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
+/–/ENTER/MENU
á
RECORDING A TV PROGRAM
RECORDING AND VIEWING THE
SAME TV PROGRAM
1
Load a cassette tape with the erase prevention tab
intact.
2
Press the SPEED button to
select the desired tape speed
SP or SLP. The counter and SP
or SLP will appear on the screen
about 4 seconds.
3
Set the TV/CATV option to the appropriate position
(See page 16).
TV
- VHF/UHF channels
CATV - CABLE TV channels
NOTES: • If power is switched off during recording,
4
Press the Direct Channel Selection buttons or CH C
or D button to select the channel to be recorded.
5
Press the REC/OTR button.
"
" and the channel number will
appear on the screen and the REC
indicator will light.
TO STOP RECORDING
Press the STOP button to stop recording.
"
" will appear on the screen.
TO STOP RECORDING TEMPORARILY
Press the PAUSE/STILL button to avoid recording
unwanted material.
"
" will appear on the screen and the REC indicator will
blink on and off. Press the PAUSE/STILL button or the
REC/OTR button to continue the recording.
NOTE: The PAUSE mode will be changed to STOP mode
ñ
after five minutes to prevent damage to the tape.
NOTES: • AUTO REWIND FEATURE
This TV/VCR will automatically rewind the video
cassette when the tape has ended (except
during OTR and Timer Record). It will also eject
the video cassette.
• If the erase prevention tab is removed, the tape
will eject when the REC/OTR button is pressed
for recording.
the TV set goes off and the VCR continues
to record. Press the STOP button to halt
the recording and turn off the VCR.
• The TV/VCR Channel cannot be changed
during recording.
00 : 00 : 00 SP
CH 012
21
Advertisement
Table of Contents
