1. Manuals
  2. Brands
  3. CamPilot Manuals
  4. IP Camera
  5. MR100-CP95H
  6. Instruction manual

CamPilot MR100-CP95H Instruction Manual

Ip box camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
C a m P i l o t M R 1 0 0
I P B O X C A M E R A
M R 1 0 0 - C P 9 3 H
M R 1 0 0 - C P 9 5 H
Instruction Manual
Before installing and using the camera, please read
this manual carefully.
Be sure to keep it handy for later reference.
CamPilot MR100
INSTRUCTION MANUAL
N
V
S
(Network Video Streamer)
User's Guide
CamPilot MR100
Instruction Manual
20100806
1 / 52

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MR100-CP95H and is the answer not in the manual?

Questions and answers

Summary of Contents for CamPilot MR100-CP95H

  • Page 1 M R 1 0 0 - C P 9 3 H M R 1 0 0 - C P 9 5 H Instruction Manual Before installing and using the camera, please read CamPilot MR100 this manual carefully. Instruction Manual Be sure to keep it handy for later reference.
  • Page 2 • Easy to use - CamPilot MR100 doesn’t require an additional PC for operation. Users can monitor video /audio data from CamPilot MR100 through a regular PC’s Web Browsers (Explorer or Netscape).
  • Page 3 ■ Mounting Surface The mounting surface material must be strong enough to support the camera. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CamPilot MR100 3 / 52...

  • Page 4: Troubleshooting

    - Is the RS485 control setting(Protocol, Baudrate, Control ID and etc.) correct? ▲ If the DIO is not work - Is the DIO cable attached securely? - Is the connected sensor or alarm device normal CamPilot MR100 4 / 52...

  • Page 5: Dimension (Mm)

    INSTRUCTION MANUAL EXTERNALS ▲ APPEARANCE ▶ Top ▶ Rear ▶ Side ▶ Front DC Iris connector Back Focus adjustment lever ▲ DIMENSION (mm) CamPilot MR100 5 / 52...

  • Page 6: Installation

    CAUION : Check for polarity when using a POE(Power of Ethernet) power supply. - Support: IEEE 802.3af ▲ LENS SOCKET CONNECTION DC Driven (DC) 1. control – 2. control + 3. drive + 4. GND CamPilot MR100 6 / 52...

  • Page 7: Adjustment Of Back Focus

    Then turn the potentiometer back to the right (in direction ”H”) just a little bit. 3. Check the lens performance by using the camera under different and/or changing light conditions. CamPilot MR100 7 / 52...

  • Page 8: Focusing The Camera Lens

    I.R. light will get through to the camera chip and the focus adjustment is done according to this spectrum, only. Attention: I.R. light can only be used in combination with mono cameras, not color cameras! CamPilot MR100 8 / 52...

  • Page 9: Osd Menu Settings

    9 . E X I T MIRROR EXIT SHARPNESS SAVE & EXIT GAMMA FACTORY FREEZE NEGA 3D_DNR D_ZOOM 5 . M O T I O N MOTION SET WINDOW ALL SET ALL CLEAR SENSITI SHOW INDI DELAY OUT CamPilot MR100 9 / 52...

  • Page 10: Network Configuration

    • DC 12V - Power (Adapter , DC 12V/1000mA) • ETHERNET - LAN cable (RJ45 Jack) - A client PC or a network devices is connected to the CamPilot MR100. • AUDIO - Audio IN/OUT cable - IN : Input from a microphone (RCA) - OUT : Output to a speaker (RCA) ※...
  • Page 11 - The programs like ENCP, NDC Manager, NDC Viewer and etc. are installed after the whole process. ▶ NVS 4.1 Installation 3) Assigning an IP address to the CamPilot MR100. - Assign an IP address with ENCP(Easy Network Configuration Program) - Running Start>Program>NVS 4.1> ENCP 2.0 ▶...
  • Page 12 - After the setup, click “Save” button. - Refer to “ENCP 2.0” manual for details. 5) Accessing to CamPilot MR100 with a web browser - Open a web browser on PC and enter the IP address assigned to a CamPilot MR100 as following. http:// 192.168.1.2/ ▶...

  • Page 13: Using Web Browser

    INSTRUCTION MANUAL Using Web Browser ▲ OVERVIEW • User can monitor the video and audio data and manage CamPilot MR100 through a web browser over internet. • User can select a type among encoder mode and decoder mode through a web browser.
  • Page 14 INSTRUCTION MANUAL ▲ CONNECTION • To connect to a CamPilot MR100, type the IP address that is given to the CamPilot MR100 on the address window of a web browser as below. (Refer to “ENCP 2.0” program manual to set IP address of the CamPilot...
  • Page 15 : Type the ID and Password of the administrator and click “Monitoring” button Guest login : Click “Guest Login” to enter the monitoring page of guest account Client’s IP : Displays the IP address of the connected PC. ► Monitoring Page ► Server Setting Page CamPilot MR100 15 / 52...
  • Page 16 • Note for Monitoring Page - When first connecting to monitoring page, click “Yes” to download ActiveX if “security warning” window appears. (CASE ①) ① ① ② - Click the yellow information bar to download ActiveX control. CamPilot MR100 16 / 52...
  • Page 17 INSTRUCTION MANUAL - User can download and install ActiveX Setup manually if the information bar does not appear. (CASE ②) - Click “Run” button to install ActiveX file manually (NVSOCX.exe) ► ActiveX Setup window CamPilot MR100 17 / 52...
  • Page 18 - Select a Stream to monitor - If the stream button is inactivated, check the video setting of “server setting page”. • Snapshot - Capture a JPEG Image of current video stream (JPG file creation route : C:/root) CamPilot MR100 18 / 52...
  • Page 19 704X576 720X576 • Info. - Shows the information of the transferred data from the CamPilot MR100 on the upper of the image. - FPS / Camera(Channel) Name / Resolution - Event Status : Motion Detect(red) / Digital IN(blue) / Video signal (green)
  • Page 20 - Changing the bitrate is not available on a guest account. • Enable Audio - If the box is checked the CamPilot MR100 sends the audio data with the video data. • PTZ Control - User can control PTZ camera or receiver through RS485 •...

  • Page 21: Server Setting

    INSTRUCTION MANUAL ▲ SERVER SETTING - To apply the changed setting, reboot CamPilot MR100. (Click Reboot on the menu) • Status - This is the initial page of Server Setting. - This shows network status, model information, network traffic status, connection list and system log.
  • Page 22 - Default DNS: IP Address of Default DNS server • Connection List - User can check the number of connected clients and IP addresses. • Log - “Log” displays the logs of general events of CamPilot MR100. CamPilot MR100 22 / 52...
  • Page 23 INSTRUCTION MANUAL • Basic > Network (Wired) - User can set Network Information of CamPilot MR100: IP Address, Subnet Mask, Gateway, Default DNS ① Static IP - IP Address: Ask network administrator for an appropriate address - Subnet Mask / Gateway / Default DNS : Ask network administrator - After setting, click “OK”...
  • Page 24 - If DHCP server is on the local network and you intend to allocate IP address dynamically, use this method - Select Dynamic IP tab and click “OK” button, and reboot CamPilot MR100. - If you want to select Dynamic IP, set Dynamic DNS to access CamPilot MR100. CamPilot MR100 24 / 52...
  • Page 25 - MTU : Maximum transmission unit of data - IP address of DNS sever can be set to create automatically - If your xDSL does not use static IP type, you should use Dynamic DNS setting like DHCP CamPilot MR100 25 / 52...
  • Page 26 INSTRUCTION MANUAL • Basic > Video - User can select video streaming type (Encoder or Decoder mode) - CamPilot MR100 support only an Encoder mode ① Encoder Mode CamPilot MR100 26 / 52...
  • Page 27 - Enable : Send JPEG Image via HTTP Protocol (1fps fixed) - Resolution : Select a resolution (QQVGA~D1) - Quality : High / 1 / 2 / 3 / 4 / Low ▶ Jpeg Capture CamPilot MR100 27 / 52...
  • Page 28 INSTRUCTION MANUAL • Basic > Audio Server to PC Audio Option - Audio Type : Mono (Fixed) - Audio Codec : G.711 / G.726 - Sampling Rate : 8kHz / 32kHz - Volume : -34.5~12dB CamPilot MR100 28 / 52...

  • Page 29: Digital Input

    INSTRUCTION MANUAL • Basic > Event ① Digital Input CamPilot MR100 29 / 52...
  • Page 30 - Digital Output Enable: enables the CamPilot MR100to send the digital signal to the connected device - Digital Output Time: adjusts the time for the CamPilot MR100to send the signal (unit : sec) - Enable: enables the CamPilot MR100to send captured image to FTP server...
  • Page 31 INSTRUCTION MANUAL ② Motion Detection Preset : Same as “Digital Input” setting Digital Output : Same as “Digital Input” setting FTP : Same as “Digital Input” setting SMTP (e-mail) : Same as “Digital Input” setting CamPilot MR100 31 / 52...
  • Page 32 INSTRUCTION MANUAL ③ Periodic Timer Common - Periodic Timer Enable : enables the CamPilot MR100 to send the signal to the client PC periodically - Time Interval : means the period (sec.) Preset : Same as “Digital Input” setting form Digital Output : Same as “Digital Input”...
  • Page 33 • Basic > Date / Time ① Current Time Set Date / Time - Server Time : the time that the CamPilot MR100 keeps internally - New Date / Time: user can assign the specific time voluntarily. CamPilot MR100 33 / 52...

  • Page 34: Time Server

    - Time zone: user can select a time zone - Daylight Saving Time : Check this box in using daylight saving time - Time Server: user can assign a Time Server to apply the current time to CamPilot MR100 - After setting, click the “OK” button and reboot CamPilolt.
  • Page 35 INSTRUCTION MANUAL • Basic > OSD (On Screen Display) Text Color - Background Color : Select a color of background - Foreground Color : Select a color of text - Transparency : 0~10 CamPilot MR100 35 / 52...
  • Page 36 - Enable: Check the box to display the image - X Axis: Input a point on the coordinate - Y Axis: Input a point on the coordinate Date / Time / Channel Name OSD logo ► OSD on image CamPilot MR100 36 / 52...
  • Page 37 Direction Keys - Operate the OSD setting menu of CamPiot MR100. - Select a value on the OSD setting menu of CamPiot MR100. ※ For detail setting values, refer to page 13. (OSD MENU SETTINGS) CamPilot MR100 37 / 52...
  • Page 38 - Baud rate / Data bits / Parity / Stop bits : select the value properly by the receiver type RS232 - Baud rate / Data bits / Parity / Stop bits : select the value properly by the receiver type CamPilot MR100 38 / 52...
  • Page 39 Record Setting - Mode : Select a record type (OFF / Full Recording / Event Recording) - Select a video stream of CamPilot MR100 (1st / 2nd / 3rd Stream) - Select a overwrite setting of the local storage (ON/OFF) File list - Recorded file is produced every 10 MB.
  • Page 40 INSTRUCTION MANUAL • Expert > Port - Web Port: Default is 80 - FTP Port: Default is 21 CamPilot MR100 40 / 52...
  • Page 41 : Only connections from the local area are permitted - MEDIUM : Video and Audio connections from any place and setting from the local area permitted. - LOW : All connections from any place permitted CamPilot MR100 41 / 52...
  • Page 42 - The administrator can add up to 5 users and modify the properties. Guest Permission - This is to determine the guest permission for access to the CamPilot MR100 - At guest account, video and audio monitoring is permitted. Max Client Limit...
  • Page 43 - DDNS is the function that matches an IP address and a host name. - If a CamPilot MR100 has the dynamic IP address, the host name by DDNS (Dynamic Domain Name Service) must be used instead of the IP address for the credibility of the network connection.
  • Page 44 - For use of “ddns.nu” register at www.dyndns.com/ - Type the registered DDNS ID, DDNS Password, Host name and Interval for updating and click “OK” button and reboot the CamPilot MR100. ▶ Main page of “DynDNS” CamPilot MR100 44 / 52...
  • Page 45 - ProutDNS is a set of PHP scripts to create your own Dynamic DNS service. - Type the DDNS server, the registered DDNS ID, DDNS Password, Host name and Interval for updating and click “OK” button and reboot CamPilot MR100. ▶Main page of “ProutDNS”...
  • Page 46 INSTRUCTION MANUAL • Expert > UPnP UPnP - Enable : Check the box to use UPnP(Universal Plug and Play) of CamPilot MR100 - Friendly name : User can change the friendly name of CamPilot MR100 CamPilot MR100 46 / 52...
  • Page 47 - Detect Area: if the detection area is selected, it changes to green (User can check preview image assuming JPEG Capture enable on the video setting page.) - Sensitivity : 1~30 (Maximum sensitivity in case of the value “1”) CamPilot MR100 47 / 52...
  • Page 48 (After that, it is required to refresh the web browser. Please push F5 button.) - Language File : Add a language file Firmware Update - Uploads the newly firmware after clicking the browsing button and finding a new firmware. CamPilot MR100 48 / 52...
  • Page 49 - Changes the logo image on OSD. - The process is same as “Firmware Update” - User have to use file name by “osd_logo.bmp” (Maximum size : 120x38) Control Protocol Upload - Add a camera control protocol. CamPilot MR100 49 / 52...
  • Page 50 INSTRUCTION MANUAL • Expert > Report Report - User can check all of setting of CamPilot MR100. - User or installer can memo on the report page. - User or installer can print out this pages and use in various usages •...

  • Page 51: Common Specifications

    INSTRUCTION MANUAL SPECFICATION ▲ Common Specifications MODEL CamPilot MR100 GENERAL SPEC NTSC ARM9E 240MHz Flash Memory System 64MB Embedded Linux Compression Type H.264 / MJPEG / MPEG-4 Resolutions D1 ~ QQVGA Bitrate 32Kbps ~ 8Mbps Video 30/25 (NTSC/PAL) fps in all resolutions...

  • Page 52: Camera Specifications

    INSTRUCTION MANUAL ▲ Camera Specifications MODEL CamPilot MR100 GENERAL SPEC NTSC 1/3" Sony Super HAD Ⅱ CCD Type Pixels 410K 470K 520 TV Line [Color] Resolution 560 TV Line [TDN (BW)] Color : 0.14Lux [F1.2, 30IRE] Min. Illumination B/W(TDN) : 0.01Lux [F1.2, 30IRE]...

This manual is also suitable for:

Mr100-cp93h

Table of Contents