Summary of Contents for DSX Access System, Inc. algo 8028
- Page 1 Empowered by Innovation Algo 8028 SIP Doorphone Manual P/N 1093100ALGO August 19, 2015 Printed in U.S.A. For additional resources, visit our Technical Support site on the web at http://www.necdsx.com...
- Page 2 This manual has been developed by NEC Corporation of America. It is intended for the use of its customers and service personnel, and should be read in its entirety before attempting to install or program the system. Any comments or suggestions for improving this manual would be appreciated. Forward your remarks to: NEC Corporation of America General Channel Shelton, CT 06484...
-
Page 3: Table Of Contents
Contents Chapter 1: Algo 8028 SIP Doorphone..............5 Description................................6 Door Box, Algo 8028 SIP Doorphone.....................6 Programming............................... 11 Programming the Algo 8028 SIP Doorphone..................11 Operation................................17 Door Box, Algo 8028 SIP Doorphone....................17 Chapter 2: Program 1000..................19 Configuration...............................20 1114: Door Chimes..........................20 Timers..................................22... -
Page 5: Chapter 1: Algo 8028 Sip Doorphone
Chapter Algo 8028 SIP Doorphone... -
Page 6: Description
Description The Algo 8028 SIP Doorphone is a SIP-based Door Box used to monitor an entrance door and is an alternative to the traditional analog DSX Door Box (P/N 922450). The 8028 consists of a Door Station (Door Box), a Control Unit, and a Power Supply. - Page 7 Algo 8028 SIP Doorphone In a wet application, relay contacts are powered by the built-in 24 VDC/300mA auxiliary power supply or by a customer-provided auxiliary supply. In these applications, it is required that current flow through the contacts to the connected device for proper operation.
- Page 8 Algo 8028 SIP Doorphone 8028 SIP Doorphone Connections Basic Connections Using the diagram above and your 8028 SIP Doorphone Installation and User Guide as references, connect the doorphone as follows: 1. Using a suitable length of 24AWG twisted pair cable, connect the red and green terminals on the supplied modular jack to the CTRL terminals on the Door Station.
- Page 9 Algo 8028 SIP Doorphone Verify the 8028 Control Unit Front Panel LEDs After about 30 seconds, verify the Control Unit front panel LEDs. The LEDs will be different after you program the doorphone and the DSX. Power: On steady then blinks off briefly every 2 seconds.
- Page 10 Algo 8028 SIP Doorphone | 10 • Paging • Door Box chimes 1-3 can broadcast over the External Paging speakers. An extension user can press and dial to answer the chimes and use their soft keys to control the associated relay.
-
Page 11: Programming
Doorphone Algo 8028 Startup Programming 1. Open the Algo 8028 SIP Doorphone Control Panel in a web browser. 1. In the browser address line, enter the IP Address of the 8028 Control Unit you obtained during initial setup. See Get the 8028 Control Unit IP Address on page 9 for more. You'll see the Control Panel opening screen: 2. - Page 12 Algo 8028 SIP Doorphone | 12 3. Enter the following in the SIP screen and click when you are done: Save a) SIP Domain: The IP address of the DSX. b) Extension: The IP extension number of the doorphone (e.g., 401).
- Page 13 Description Relay (RFC 2833) [Default] Inband SIP (SIP INFO) 4. Verify the Algo 8028 Control Unit LEDs Power: On steady then blinks off briefly every 2 seconds. Telephone: On steady then blinks off briefly every 2 seconds. Door Station: On steady.
- Page 14 Algo 8028 SIP Doorphone | 14 Option Description [Default] Normal Ring Group ringing. Low pitch chime pattern. Mid range pitch chime pattern. High pitch chime pattern. 2. 1605-06: Door Alert Timer [System: Timers: Features: Control (1605): Door Alerting] on page 22 Set the length of time the doorphone will remain active after a visitor at the door presses the doorphone Call button.
- Page 15 Enter a valid unique DTMF digit for Latch Closed Code (e.g., 4). 2. 2101-07: Open Code [Stations: Config: Setup: Type (2101): Open Code] on page 27 Enter the same DTMF digit you entered in the Algo 8028 for Latch Open Code (e.g., 5).
- Page 16 0-9, # and * DTMF digit. [Default] no entry. 3. 2101-08: Close Code [Stations: Config: Setup: Type (2101): Close Code] on page 28 Enter the same DTMF digit you entered in the Algo 8028 for Latch Closed Code (e.g., 4). Option Description 0-9, # and * DTMF digit.
-
Page 17: Operation
Algo 8028 SIP Doorphone | 17 Operation Door Box, Algo 8028 SIP Doorphone Calling to and from the Doorphone To place a call from the Doorphone: 1. Press the Doorphone call button. 2. When someone inside the building answers your call, speak toward the Doorphone. -
Page 19: Chapter 2: Program 1000
Chapter Program 1000... -
Page 20: Configuration
To make it easier for users to determine which Door Box is ringing, program chime 1 to ring one, two, or three times. Features Related to this Program Telephone Features • Door Box • Door Box, Algo 8028 SIP Doorphone on page 6 IntraMail Features • None Program Options Single Single chime 1 sound... - Page 21 Program 1000 | 21 Features Related to this Program Telephone Features • Door Box • Door Box, Algo 8028 SIP Doorphone on page 6 IntraMail Features • None Program Options Single Single chime 3 sound Double Double chime 3 sound...
-
Page 22: Timers
Door Alert Time to connect to the Door Box. Features Related to this Program Telephone Features • Door Box • Door Box, Algo 8028 SIP Doorphone on page 6 IntraMail Features • None Program Options 0-9999 Door Box Alert Time (seconds). [Default] = 30. -
Page 23: Voip Profile
SIP Info: DTMF is relayed out-of-band using the SIP protocol (SIP INFO packets) and is independent of RTP • or the audio stream. Features Related to this Program Telephone Features • Door Box, Algo 8028 SIP Doorphone on page 6 • VoIP Extensions IntraMail Features • None. -
Page 25: Chapter 3: Program 2000
Chapter Program 2000... -
Page 26: Configuration
Use this option to assign circuit type to station devices. All circuit types should auto-ID when the station device is plugged in. Features Related to this Program Telephone Features • Direct Station Selection (DSS) Console • Door Box, Algo 8028 SIP Doorphone on page 6 • Station Key Telephones IntraMail Features • None Program Options... - Page 27 Open 2. If the connected device is a SIP doorphone (like the Algo 8028), use this option to enable DTMF relay control. If enabled, for example, when a keyset user answers the doorphone call and presses their soft key, DSX...
-
Page 28: 2106: Voip
Available in software versions 3.43 and higher. If the extension is a doorphone with DTMF relay control (such as the Algo 8028), use this option to assign the DTMF digit that will deactivate the doorphone relay. When the keyset user talking to the doorphone presses the soft key, the system will send the digit specified in this option to the doorphone. - Page 29 Program 2000 | 29 Features Related to this Program Telephone Features • Department Groups • Extension Hunting • Group Ring IntraMail Features • None. Program Options 1-30 Department Group 1-30. [Default] None.
-
Page 30: Department Groups
Program 2000 | 30 Department Groups 2301: Group Identification 2301-03: Department Group Type [Stations: > Department Groups: > Setup: > Identification (2301): > Group Type] Available in software versions 3.01 and higher. Use this option to assign the Department Group type (e.g., Ring Group or UCD Group). Features Related to this Program Telephone Features •... - Page 31 NEC Corporation of America General Channel 4 Forest Parkway Shelton, CT 06484 www.necdsx.com Printed in U.S.A. (1093100ALGO)
Need help?
Do you have a question about the algo 8028 and is the answer not in the manual?
Questions and answers