Page 4
You then have to decide between the “Keeloq duplication modes” explained in section 2.2.1.1. to complete recording. sr-4v: red: 433, 92 MHz / green: variable 7 – 4 if the code is erreka, Bft or aPriMatic, the duplicate remote sr-48: red: 433, 92 MHz / Blue: 868 MHz led will go back to red while waiting for a third screen.
Page 5
7 – 1 the short range remote goes green. if the code received is correct, •automatic duplication Mode the green led starts flashing. then you have to decide between the auto Press the first button of the duplicate remote when the “automatic/clone/ non-evolutionary clone duplication modes”...
Page 6
4.4DIAGRAM OF THE STEpS NEEDED WHEN COpYING 4.4.1 SR-4V 4.4.2 SR-48 4.4.3 SR-4Q...
When you have finished this installation you can execute the ‘clienteroll- fixProx.jar’ programme. if the application asks which programme you want 5. pC OpERATION to use to open it (with java installed) use the jarfix.exe programme (in the clienterollfixWindows folder) to simply connect the .jar extension to java. the sr remote can be connected to a Pc using a special 6-pin cable on one end and a usB connection at the other.
g. delete the default driver h.“rmmod ftdi_sio” i. install the new driver j. “insmod ftdi_sio.o” 2. install the most up to date ftdi_sio linux version for your operating system a. /sbin/modprobe -v ftdi_sio if there are communication problems, try some of the following solutions: When connecting the usB, check whether it has been properly set up with the following instructions: lsusb - >...
Page 9
the application is contacting the remote to initiate the copy process, press the ‘start’ button. the remote’s red led will once you are connected, the ‘sr remote’ option and all its options can be start to flash and will display the following message. used.
Page 10
desired serial number. once the remote has captured the code from the original, the application will display a message concerning the information received. for rolling if you wish to delete them, press the del key. code remotes, the application will display the following screen showing once the serial number has been modified, press the enter key to confirm.
Page 11
When you select the frequency, the remote starts to save the information 5.2.5 fiXed code and displays the following message. a similar process is used to copy fixed codes. once the remote has cap- tured the fixed code, the application will display the following window: When the copy is completed, the application will display “correct coPY”...
Page 12
if the code read and the saved code coincide, the application will display the following message: ‘verification oK’. if this is not the case it will produce an error message. the information saved on the remote will appear on the screen. the code type is displayed first.
Page 13
When you press ‘start reading’ you will be asked to enter the original remote’s code type (binary or ternary*), frequency (433 or other) and When you press ‘Yes’, a new window opens where you can enter the key switch positions. to enter the switch positions, you first have to data in order to find the code in future searches.
Page 14
then, if there are more buttons for recording information than the Press ‘next’ to see the following screen, where you must select the original remote, press ‘next’ and the application will ask you to press the button(s) to record the code read. corresponding button.
Page 15
following remote has been generated: XXXXX’ 5.2.8 generate a rolling code reMote if you don’t know the information to enter to generate a remote, you can this option allows you to generate a series of rolling codes that are recog- load a previously saved code and modify the desired data, normally the nised by the application.
Page 16
5.2.9 generating fiXed reMotes as with rolling codes, this option allows you to generate fixed code remo- tes from among those reprogrammed in the application or to load a code that you stored earlier. When you select this option, the following window opens. When the copy has finished, the application displays a reminder of the frequency to which this remote should be set.
Page 17
5.2.10 faac screens You can see how they tried to copy a faac code on button 1, but not on the other this option is a specific function for copying faac slH remotes. faac buttons. remotes can be master and slave remotes. to copy a faac remote, you need to transfer the seed code from the master remote to the duplicate then press the ‘create screens file’...
Page 18
5.2.12 original analYsis this option allows us to analyse the original remote without having to perform the entire ‘guided duplication’ process. When you press this option, the following screen opens: as when making a guided duplicate, when the remote analysed is a fixed code remote it asks you to press ‘enter’...
Page 19
When you close the window, it will give the option to copy or not to copy 3. after 10 seconds, the receiver will exit programming mode and will emit 2 short the read code. if you wish to copy it, the programme jumps to the guided beeps.
Page 20
When the led on the receiver lights up, release the button. REGISTERING NICE REMOTES 2. Press the button on the remote you wish to register. nice receivers enable you to register remotely and directly on the receiver. the receiver will emit a short beep to indicate that the remote has been registe- the Bio version and regenerative versions of the verY and flo models must red.
Page 21
REGISTERING EVOLuTIONARY CELINSA REMOTES in evolutionary mode, celinsa receivers can be registered remotely or REGISTERING EVOLuTIONARY GO REMOTES directly on the receiver. the go remote is activated directly on the receiver the first time you press Remote registration it. However this option is disabled on some installations and you have to 1.
Page 22
2695-733 sâo joao da talha www.jmafrance.fr service.commercial@jmafrance.fr www.jmaportugal.com comercial@jmaportugal.com JMA INDIA jMa KeYs india Pvt. ltd JMA uK tel +91 124 428 5450 sKs ltd fax +91 124 428 5451 tel +44 144 229 1400 H-239 & H-240, sushant shopping arcade...
Need help?
Do you have a question about the SR-4V and is the answer not in the manual?
Questions and answers