Table of Contents
Advertisement
Quad Receiver
SPECIFICATIONS
Working Environment
Water resistance .................... Designed to work in an indoor or outdoor
Power Source
Input Voltage ................................
Power Requirements
12 V DC .................................
NOTE:
When upgrading or replacing a legacy "ImproX UHF Receiver", make sure
to reconnect using a 12V DC supply.
INSTALLATION INFORMATION
CAUTION:
These two models of the Impro Quad Receiver only support
connection to the Impro IXP220 Controller, IXP20 Controller, iTRT
(Intelligent Twin Reader Terminal), MfT (Multi-function Terminal), TA
(Time Attendance Terminal), and the Impro UniScan and FlexiScan
Controllers. DO NOT attempt to connect this Receiver to an Impro
(DT) Door Terminal.
433.92 MHz 4-Channel RF Receiver
INSTALLATION MANUAL
MODEL NUMBERS: HRR900-0-1-GB-XX
environment similar to IP44, the Impro Quad
Receiver is water resistant
11V to 15 V DC (Polarity sensitive)
Current (mA)
60
HRR901-0-1-GB-XX
Power (W)
0.7
Advertisement
Table of Contents
Summary of Contents for impro HRR901
-
Page 1: Installation Manual
Impro IXP220 Controller, IXP20 Controller, iTRT (Intelligent Twin Reader Terminal), MfT (Multi-function Terminal), TA (Time Attendance Terminal), and the Impro UniScan and FlexiScan Controllers. DO NOT attempt to connect this Receiver to an Impro (DT) Door Terminal. - Page 2 Top Cover (press-down firmly to clip into the base). • A black gland plate for power, data and RF (in the case of the HRR901) lines into the unit (this needs to be drilled to accommodate the wiring during installation). •...
-
Page 3: Line-Of-Sight
Impro Quad Receiver by either blocking, absorbing or interfering with the transmitted signal from the Quad Transmitter. Due to the radiation pattern of the integral antenna, it is preferable to install the Impro Quad Receiver in a high position, with its integrated antenna pointing down. If this is not possible, then consider using the HRR901-0-1-GB-XX with an external antenna that meets the requirements of the installation. -
Page 4: Transmit-Receive (Reciprocity) Trouble Shooting
The Impro Quad Receiver has a built-in LED RSSI (Received Signal Strength Indicator) bar graph. Before permanently mounting the Quad Receiver (or the external antenna for HRR901) to a surface, it is recommended that the RSSI is checked with the receiving antenna temporarily held in its proposed mounting position, and the Impro Quad Transmitter at the expected point of entry or exit. - Page 5 Four Channel Operation When using the Impro Quad Receiver and a single Impro (iTRT) Intelligent Twin Reader Terminal (XRT910-0-0-GB-XX, XRT920-0-0-GB-XX, IPS920-0-0-GB-XX or IPS921-0-0-GB-XX), only two Push-buttons on the Impro Quad Transmitter (TRK900-1- 1-GB) are available for use. To use all four of the Quad Transmitter’s Push-buttons, connect two Impro (iTRT) Intelligent Twin Reader Terminals (XRT910-0-0-GB-XX, XRT920-0-0-GB-XX, IPS920- 0-0-GB-XX or IPS921-0-0-GB-XX), to the Quad Receiver, see Figure 3.
- Page 6 Make a mark on the Gland Plate corresponding exit points that will have the wires run NEXT to, and NOT OVER the Impro Quad Receiver PCB (if using the built-in antenna, this area must be kept cleared of any objects).
- Page 7 Connecting the Impro Quad Receiver Figure 4 to 10 show typical electrical connection diagrams for the Receiver. Figure 4: Impro Quad Receiver Connected to the IXP220 Controller HRR300-0-0-GB-01 April 2013 Page 7...
- Page 8 Figure 5: Impro Quad Receiver Connected to the IXP20 Controller HRR300-0-0-GB-01 April 2013 Page 8...
- Page 9 Figure 6: Impro Quad Receiver Connected to the Impro iTRT HRR300-0-0-GB-01 April 2013 Page 9...
- Page 10 Figure 7: Impro Quad Receiver Connected to two Impro PT/TA Terminals HRR300-0-0-GB-01 April 2013 Page 10...
- Page 11 Figure 8: Impro Quad Receiver Connected to the Impro MfT HRR300-0-0-GB-01 April 2013 Page 11...
- Page 12 Figure 9: Impro Quad Receiver Connected to the Impro FlexiScan Controller HRR300-0-0-GB-01 April 2013 Page 12...
- Page 13 Figure 10: Impro Quad Receiver Connected to the Impro UniScan Controller HRR300-0-0-GB-01 April 2013 Page 13...
-
Page 14: Guarantee Or Warranty
GUARANTEE OR WARRANTY This product conforms to our Guarantee or Warranty details placed on our Web Site, to read further please go to www.impro.net. User Notes HRR300-0-0-GB-01 April 2013 Page 14... - Page 15 User Notes HRR300-0-0-GB-01 April 2013 Page 15...
- Page 16 This manual is applicable to both variants of the Impro Quad Receiver, HRR900-0-1-GB-XX and HRR901-0-1-GB-XX. (The last two digits of the Impro stock code indicate the issue status of the product). April Impro QR\English Manuals\LATEST ISSUE\Quad HRR300-0-1-GB-01 Issue 2 2013 Rec-insm-en-02.docx...