Page 1 Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING Two Wheel Drive Four Wheel Drive Anti-Lock Brake System Accessory AI-SHIFT Artificial Intelligence shifting Automatic Locking Retractor A-TRAC Active Traction Control AUTO LSD Automatic Limited Slip Differential Calibration Child Restraint System Electronic Control Unit Event Data Recorder Emergency Locking Retractor Flexible Fuel Vehicle...
Page 2 Abbreviation list ABBREVIATIONS MEANING Resume RSCA Roll Sensing of Curtain shield Airbags Supplemental Restraint System Tire Identification Number TPMS Tire Pressure Warning System TRAC Traction Control Treadwear indicators Trailer Weight Rating Vehicle Identification Number Vehicle Stability Control...
Page 3: For Your Information
Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 4 ● Anti-lock brake system ● SRS airbag system ● Seat belt pretensioner system Be sure to check with your Toyota dealer for precautionary measures or spe- cial instructions regarding installation of a mobile two-way radio system. Scrapping your Toyota The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals.
Page 5 The computers do not record conversations, sound or pictures. ● Data usage Toyota may use the data recorded in these computers to diagnose malfunc- tions, conduct research and development, and improve quality. Toyota will not disclose the recorded data to a third party except: •...
Page 6 EDR. ● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehicle) is obtained •...
Page 7 CAUTION ■ General precautions while driving Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
Page 8 This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
Page 10 TABLE OF CONTENTS Adjusting and operating features such as door locks, Before driving mirrors, and steering column. When driving Driving, stopping, and safe-driving information. Interior and Air conditioning and audio systems, as well as other in- exterior features terior features for a comfortable driving experience. Maintenance Cleaning and protecting your vehicle, performing do-it- and care...
Page 11 Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made by your Toyota dealer using the key number plate. (→P. 646)
Page 12 1-1. Key information NOTICE ■ To prevent key damage (vehicles with engine immobilizer system) ● Do not subject the keys to strong shocks, expose them to high tempera- tures by placing them in direct sunlight, or get them wet. ● Do not expose the keys to electromagnetic materials or attach any mate- rial that blocks electromagnetic waves to the key surface.
Page 13 1-2. Opening, closing and locking the doors ∗ Wireless remote control The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle. Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors.
Page 14 1-2. Opening, closing and locking the doors ■ Wireless remote control battery depletion The standard battery life is 1 to 2 years. (The battery becomes depleted even if the wireless remote control is not used.) If the wireless remote control function does not operate, the battery may be depleted.
Page 15 1-2. Opening, closing and locking the doors ■ Customization ● That can be configured at Toyota dealer (vehicles without multi-informa- tion display) Settings (e.g. wireless remote control) can be changed. (Customizable features →P. 696) ● It is possible to change the settings (vehicles with multi-information dis- play) (Feature customization →P.
Page 16 1-2. Opening, closing and locking the doors Side doors The vehicle can be locked and unlocked using the wireless remote control, key or door lock switch. ■ Wireless remote control (if equipped) →P. 46 ■ Vehicles without power door lock system Locks the door Unlocks the door Vehicles with power door lock system...
Page 17 1-2. Opening, closing and locking the doors ■ Door lock switch (if equipped) Driver’s door lock switch Locks all doors Unlocks all doors Passenger’s door lock switch Locks all doors Unlocks all doors ■ Inside lock button Locks the door Unlocks the door Pulling the door handle can open the front door even if the...
Page 18 1-2. Opening, closing and locking the doors Locking the front doors from the outside without a key Move the inside door lock button to the lock position. Close the door. Vehicles with power door lock system The door cannot be locked if a front door is open and the key is in the engine switch.
Page 19 10 seconds after turn- door unlocking function ing the engine switch to the ACC or LOCK position. ■ Setting and canceling the functions Vehicles with multi-information display →P. 203 Vehicles without multi-information display To switch between setting and canceling, contact your Toyota dealer.
Page 20 A buzzer sounds if the driver’s door is opened, while the engine switch is in the ACC or LOCK position to remind you to remove the key. ■ Customization that can be configured at Toyota dealer Settings (e.g. door lock) can be changed. (Customizable features →P. 696) CAUTION ■...
Page 21 1-2. Opening, closing and locking the doors Tailgate The tailgate can be opened using the tailgate handle. The tailgate can be locked/unlocked using a key. ■ Tailgate handle Pull the handle Open the tailgate slowly The support cables will hold the tailgate horizontal.
Page 22 1-2. Opening, closing and locking the doors Removing the tailgate ■ Before removing the tailgate (vehicles with rear view monitor system) These connector covers are used when removing the tailgate, to prevent the back-up camera wire harness connectors from being contaminated.
Page 23 1-2. Opening, closing and locking the doors Open the tailgate. Pull out the plastic wire protector located in the vehicle bed by pressing the tabs and pulling the protector. Plastic wire protector Pull out the wire harness from the vehicle bed. Attach connector cover...
Page 24 1-2. Opening, closing and locking the doors ■ Removing the tailgate Open the tailgate to the angle where you can release the brackets on the support cables from the lugs on both sides. Lift the support cable bracket up and slide it off. To unhook the support cable bracket, keep pulling up the clip on the bracket and unhook the...
Page 25 1-2. Opening, closing and locking the doors Slide the tailgate a little to the right to unhook the left side. To attach the tailgate, follow the removal procedure in reverse order. Rear step bumper Type A For rear end protection and eas- ier step-up loading.
Page 26 1-2. Opening, closing and locking the doors CAUTION ■ Before removing the tailgate (vehicles with rear view monitor system) Disconnect the wire harness between the back-up camera and the vehicle. Failure to do so may result in serious personal injury or damage to the vehi- cle components.
Page 27 1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Manual seats (Separated type seats) Passenger’s seat Driver’s seat Seat position adjustment lever Seatback angle adjustment lever Double Cab and CrewMax models Driver’s seat vertical height adjustment lever Driver’s seat cushion (front) angle adjustment knob Driver’s seat lumbar support adjustment switch (if equipped)
Page 28 1-3. Adjustable components (seats, mirrors, steering wheel) Manual seat (Bench type seat) Seat position adjustment levers Seatback angle adjustment levers Center seat seatback angle adjustment lever Double Cab and CrewMax models Driver’s seat vertical height adjustment lever Driver’s seat cushion (front) angle adjustment knob...
Page 29 1-3. Adjustable components (seats, mirrors, steering wheel) Power seat Passenger’s seat Driver’s seat Seat position adjustment switch Seatback angle adjustment switch Driver’s seat cushion (front) angle adjustment switch Driver’s seat vertical height adjustment switch Driver’s seat leg support adjustment switch (if equipped) Seat lumbar support adjustment switch (if equipped)
Page 30 1-3. Adjustable components (seats, mirrors, steering wheel) Folding passenger’s seat (if equipped on Regular Cab models) ■ Before folding passenger’s seat Push the seat belt hanger down as far as it will go when it is in the raised position. Pass the seat belts through the seat belt hanger.
Page 31 1-3. Adjustable components (seats, mirrors, steering wheel) Pull the seatback folding lever and fold the seatback down. CAUTION ■ Seat adjustment ● Be careful that the seat does not hit passengers or luggage. ● Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt.
Page 32 1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats (Double Cab and CrewMax models) CrewMax models Seat position adjustment lever Seatback angle adjustment lever Double Cab models The rear seats do not have a seat adjustment function.
Page 33 1-3. Adjustable components (seats, mirrors, steering wheel) Raising the bottom cushion (Double Cab models) ■ Before raising the bottom cushion Stow the seat belt buckles. This prevents the seat belt buck- les from falling out when you fold the seatback. Pass the seat belts through the seat belt hangers.
Page 34 1-3. Adjustable components (seats, mirrors, steering wheel) Folding down rear seats (CrewMax models) ■ Before folding down rear seats Stow the rear seat belt buckles. This prevents the seat belt buck- les from falling out when you fold the seatback. Pass the seat belts through the seat belt hangers.
Page 35 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When adjusting a rear seat (CrewMax models) ● Be careful that the seat does not hit passengers or luggage. ● Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt.
Page 36 1-3. Adjustable components (seats, mirrors, steering wheel) NOTICE ■ When folding the seats ● The seat belts and buckles must be stowed. ● CrewMax models: Do not fold the rear seat seatback forward with the lug- gage cover hooks attached.
Page 37 1-3. Adjustable components (seats, mirrors, steering wheel) ∗ Driving position memory (driver’s seat) Your preferred driving position (the position of the driver’s seat, steering wheel and outside rear view mirrors) can be entered into the computer’s memory and recalled with the touch of a button. Two different driving positions can be entered into memory.
Page 38 1-3. Adjustable components (seats, mirrors, steering wheel) Linking driving position memory with door unlock operation Memorized driving positions can be recalled when you unlock the driver’s door using the wireless remote control and open the driver’s door. ■ Setting the linked door unlock operation Set the driving positions into the memory system using the “1”...
Page 39 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Retained accessory power Each memorized position (except for the tilt and telescopic steering column) can be activated within 30 seconds after the driver’s door is opened, even if the key is not in the engine switch. ■...
Page 40 1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. Front separated type seats Vertical adjustment Pull the head restraints up. Down Push the head restraint down while pushing the lock release Lock release button button.
Page 41 1-3. Adjustable components (seats, mirrors, steering wheel) Rear seat (CrewMax models) Vertical adjustment Pull the head restraints up. Down Push the head restraint down while pushing the lock release Lock release button button. ■ Removing the front head restraints Pull the head restraint up while pushing the lock release button.
Page 42 1-3. Adjustable components (seats, mirrors, steering wheel) CrewMax models Pull the head restraint up while pushing the lock release button. ■ Installing the front head restraints Align the head restraint with the installa- tion holes and push it down to the lock position.
Page 43 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the head restraints Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears. ■ Adjusting the front center seat (bench type seat) and rear center seat head restraints (Double Cab and CrewMax models) Always raise the head restraint one level from the lowermost position when...
Page 44 1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the...
Page 45 1-3. Adjustable components (seats, mirrors, steering wheel) Releasing the belt Press the release button. Release button ■ Using front seat belt (Regular Cab models) Raise the front seat belt hanger until it locks.
Page 46 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the belt Front seats (Double Cab and CrewMax models) Down Push the lock release button and slide the height adjuster down. Move the height adjuster up as needed until you hear a click.
Page 47 1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats (CrewMax models) Down Push the lock release button and slide the height adjuster down. Move the height adjuster up as needed until you hear a click. Seat belt pretensioners (front seats) The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt...
Page 48 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
Page 49 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. ● Toyota recommends that children be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system.
Page 50 ● If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer. ■ Seat belt damage and wear ●...
Page 51 Seat belt damage and wear ● Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. ● Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage.
Page 52 1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel (manually adjustable type) The steering wheel can be adjusted to a comfortable position. ■ To change the angle Hold the steering wheel and press the lever down. Adjust to the ideal position by moving the steering wheel vertically.
Page 53 1-3. Adjustable components (seats, mirrors, steering wheel) Adjust to the ideal position by moving the steering wheel horizontally. After adjustment, pull the lever up to secure the steering wheel. CAUTION ■ Caution while driving Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and an accident, resulting in death or serious injury.
Page 54 1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel (power-adjustable type) The steering wheel can be adjusted to a comfortable position. Down Toward the driver Away from the driver Auto tilt away When the key is removed from the engine switch, the steering wheel returns to its stowed posi- tion by moving up and away to enable easier driver entry and...
Page 55 1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions. Manual anti-glare inside rear view mirror Normal position Anti-glare position...
Page 56 1-3. Adjustable components (seats, mirrors, steering wheel) Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and automatically reduces the reflected light. Turns automatic mode ON/ The indicator comes on when automatic mode is turned on.
Page 57 1-3. Adjustable components (seats, mirrors, steering wheel) ■ To prevent sensor error (vehicles with auto anti-glare inside rear view mirror) To ensure that the sensors operate prop- erly, do not touch or cover them. ■ If a sun visor interferes with the mirror Hold and rotate the mirror to adjust the support.
Page 58 1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted. Power-adjustable type (Type A) Select a mirror to adjust. (L: left or R: right) Adjust the mirror up, down, in or out using the switch.
Page 59 1-3. Adjustable components (seats, mirrors, steering wheel) Power-adjustable type (Type B) Upper part mirror: Select a mirror to adjust. (L: left or R: right) Adjust the mirror up, down, in or out using the switch. Lower part mirror: Adjust the mirror up and down, in or out by pushing the mirror surface.
Page 60 1-3. Adjustable components (seats, mirrors, steering wheel) Folding back the mirrors From outside Push the mirrors towards the back of the vehicle to fold them. From inside (if equipped) Press the switch. Pressing again will unfold the mir- rors.
Page 61 1-3. Adjustable components (seats, mirrors, steering wheel) Extending the mirrors (if equipped) The mirrors can be manually slid outward improve visibility around wide trailers. ■ Recommended mirror angle when towing a trailer (vehicles with extending mirrors) Power adjust the upper part of the mir- ror until an appropriate view is obtained.
Page 62 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Automatic adjustment of the mirror angle (vehicles with driving posi- tion memory) A desired mirror face angle can be entered to memory and recalled automat- ically by the driving position memory. (→P. 70) ■...
Page 63 1-4. Opening and closing the windows and moon roof ∗ Power windows The power windows can be opened and closed using the following switches. Driver’s power window switches (Type A) Closing Opening One-touch opening (driver’s window only) : Pressing the switch in the opposite direction will stop win- dow travel partway.
Page 64 1-4. Opening and closing the windows and moon roof Driver’s power window switches (Type B) Closing One-touch closing Opening One-touch opening : Pressing the switch in the opposite direction will stop win- dow travel partway. Front passenger power’s window switch (Type A) Closing Opening...
Page 65 1-4. Opening and closing the windows and moon roof Front passenger’s power window switch (Type B) Closing One-touch closing Opening One-touch opening : Pressing the switch in the opposite direction will stop win- dow travel partway. Rear passenger’s power window switch (Double Cab and Crew- Max models) Closing Opening...
Page 66 If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
Page 67 1-4. Opening and closing the windows and moon roof CAUTION ■ Closing the windows Observe the following precautions. Failing to do so may result in death or serious injury. ● Check to make sure that all passengers do not have any part of their body in a position where it could be caught when a window is being operated.
Page 68 1-4. Opening and closing the windows and moon roof ∗ Back window The back window can be opened and closed using the lock release lever. OPEN/CLOSE Push the lock release lever and slide the back window. ■ Closing the back window Make sure that the back window is securely closed after closing it.
Page 69 1-4. Opening and closing the windows and moon roof ∗ Power back window The back window can be opened and closed using the switch. Double Cab models Opening Closing ∗ : If equipped...
Page 70 1-4. Opening and closing the windows and moon roof CrewMax models Opening Closing ■ The power back window can be operated when The engine switch is in the ON position. ■ Operating the power back windows after turning the engine switch off The power back windows can be operated for approximately 43 seconds even after the engine switch is turned to the ACC position or turned off.
Page 71 1-4. Opening and closing the windows and moon roof CAUTION ■ Closing the back window Observe the following precautions. Failing to do so may result in death or serious injury. ● Check to make sure that all passengers do not have any part of their body in a position where it could be caught when a window is being operated.
Page 72 1-4. Opening and closing the windows and moon roof ∗ Moon roof Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing Open Close To stop partway, press the switch lightly. ∗...
Page 73 1-4. Opening and closing the windows and moon roof ■ Tilt up and down Tilt up Tilt down To stop partway, press the switch lightly. ■ The moon roof can be operated when The engine switch is in the ON position. ■...
Page 74 1-4. Opening and closing the windows and moon roof ■ If the moon roof cannot be closed automatically Keep the switch depressed. ■ Sunshade The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened. ■...
Page 75 If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer. ■ Customization that can be configured at Toyota dealer Settings (e.g.
Page 76 1-4. Opening and closing the windows and moon roof CAUTION ■ Opening the moon roof Observe the following precautions. Failing to do so may cause death or serious injury. ● Do not allow any passengers to put their hands or heads outside the vehi- cle while it is moving.
Page 77 1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle Turn the engine switch off and ensure that all the doors and win- dows are closed. ■ Opening the fuel tank cap Open the fuel filler door.
Page 78 1-5. Refueling Hang the fuel tank cap on the back of the fuel filler door. Closing the fuel tank cap When installing the fuel tank cap, turn it until you hear a click. The cap will turn slightly to the opposite direction when released.
Page 79 1-5. Refueling ■ Identifying flex-fuel vehicles Flex-fuel vehicles can be identified by the fuel tank cap, which marked “FLEXFUEL E85/GASOLINE”. ■ Fuel tank capacity Approximately 26.4 gal. (100 L, 22.0 Imp.gal.) ■ E85 Fueling Stations (Flex-fuel vehicles) E85 fueling stations and fuel pumps can be identified by the indication “E85 85% Ethanol”.
Page 80 This may cause static electricity to build up, resulting in a possible ignition hazard. ■ When replacing the fuel cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 81 1-5. Refueling NOTICE ■ Refueling Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle’s painted surface. ■ To prevent damage to the fuel filler door Do not apply excessive force.
Page 82 1-6. Theft deterrent system ∗ Engine immobilizer system The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. The indicator light flashes after the key has been removed from the engine switch to indi-...
Page 83 1-6. Theft deterrent system ■ Certifications for the engine immobilizer system For vehicles sold in U.S.A. FCC ID: MOZRI-21BTY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 84 1-6. Theft deterrent system ∗ Alarm The system sounds the alarm and flashes lights when forcible entry is detected. ■ Triggering of the alarm The alarm is triggered in the following situations when the alarm is set. ● A locked door is unlocked or opened in any way other than using the wireless remote control door lock function or key.
Page 85 1-6. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type alarm system. ■ Items to check before locking the vehicle To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following. ● Nobody is in the vehicle. ●...
Page 86 1-6. Theft deterrent system ■ Alarm-operated door lock ● When the alarm is operating, the doors are locked automatically to pre- vent intruders. ● Do not leave the key inside the vehicle when the alarm is operating, and make sure the key is not inside the vehicle when recharging or replacing the battery.
Page 87 1-7. Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. (→P. 60) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed to the extent required.
Page 88 1-7. Safety information CAUTION ■ While driving ● Do not adjust the position of the driver’s seat while driving. Doing so could cause the driver to lose control of the vehicle. ● Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
Page 89 1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbags Driver airbag/front passenger airbag Can help protect the head and chest of the driver and right front...
Page 90 1-7. Safety information Airbag system components Regular Cab models Double Cab and CrewMax models...
Page 91 1-7. Safety information Side airbags Front passenger’s seat belt buckle switch AIR BAG ON and AIR BAG OFF indicator lights Occupant detection system (ECU and sensors) Curtain shield airbags warning light Front passenger airbag RSCA OFF indicator light Knee airbags RSCA OFF switch Side and curtain shield air- (4WD models only)
Page 92 1-7. Safety information ■ SRS warning light This warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensor assemblies, curtain shield air- bag sensor assemblies, driver’s seat position sensor, driver’s seat belt buckle switch, front passenger occupant classification system, AIR BAG ON and AIR BAG OFF indicator lights, front passenger’s seat belt buckle switch, front seat belt pretensioner assemblies, RSCA OFF indicator light, inflators, interconnecting wiring and power sources.
Page 93 1-7. Safety information ■ Operating conditions (side airbags and curtain shield airbags) The SRS side airbags and SRS curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to the impact force produced by an approximately 3307 lb. [1500 kg] vehicle colliding with the vehicle cabin from a direction perpendicu- lar to the vehicle orientation at an approximate speed of 12-18 mph [20-30 km/h]).
Page 94 1-7. Safety information ■ Types of collisions that may not deploy the SRS airbag (front airbags) The SRS front airbags are generally not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low- speed frontal collision.
Page 95 ● Pitching end over end ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ● The front of the vehicle is damaged or...
Page 96 1-7. Safety information ● The surface of the seats with the side airbag is scratched, cracked or other- wise damaged. ● The portion of the front pillars, rear pil- lars or roof side rail garnishes (padding) containing the curtain shield airbags inside is scratched, cracked or other- wise damaged.
Page 97 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are...
Page 98 1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not sit on the edge of the seat or lean against the dashboard. ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.
Page 99 1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not attach anything to or lean any- thing against areas such as the dash- board, steering wheel pad or lower portion of the instrument panel. These items can become projectiles when SRS driver, front passenger and knee airbags deploy.
Page 100 If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer. ■ Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer.
Page 101 1-7. Safety information Deactivating the curtain shield airbags in a vehicle rollover (4WD models only) ON/OFF (hold for a few sec- onds) The RSCA OFF indicator turns on. (only when the engine switch is in the ON position.) The roll sensing function for the curtain shield airbags and seat belt pretensioners will turn back on automatically each time the...
Page 102 1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the right front passenger seat and activates or deactivates the devices for the front passenger.
Page 103 1-7. Safety information Conditions and operation of the front passenger occupant classification system ■ Adult* AIR BAG ON and AIR BAG OFF indica- AIR BAG ON tor lights Indicator/ SRS warning light warning light Front passenger’s seat belt reminder Flashing* light Front passenger airbag Front passenger knee airbag...
Page 104 1-7. Safety information ■ Unoccupied AIR BAG ON and AIR BAG OFF indica- Not illumi- tor lights nated Indicator/ SRS warning light warning light Front passenger’s seat belt reminder light Front passenger airbag Deactivated Front passenger knee airbag Side airbag on the front passenger seat Devices Activated Curtain shield airbag in the front passen-...
Page 105 1-7. Safety information : When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/her as an adult depending on his/her physique or posture. : Never install a rear-facing child restraint system on the front pas- senger seat.
Page 106 Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. ● Double Cab and CrewMax models: Child restraint systems installed on the rear seat should not contact the front seatbacks.
Page 107 1-7. Safety information Child restraint systems A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.
Page 108 1-7. Safety information Forward facing ⎯ Convertible seat Booster seat ■ Selecting an appropriate child restraint system ● Use a child restraint system appropriate for the child until the child becomes large enough to properly wear the vehicle’s seat belt. ●...
Page 109 In an accident, the child can be crushed against the windshield, or between you and the vehicle’s interior. ● Regular Cab models: Toyota strongly urges use of a proper child restraint system which conforms to the size of the child. ●...
Page 110 1-7. Safety information CAUTION ■ Child restraint precautions ● Regular Cab models (Bench type seat): Do not install a child restraint sys- tem on the center seat if it interferes with driving operations such as changing the shift lever position. In this case, install the child restraint sys- tem on the right passenger seat.
Page 111 1-7. Safety information Installing child restraints Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.
Page 112 1-7. Safety information Anchor bracket (for top tether strap) Regular Cab models Anchor brackets are pro- vided passenger seats. Separated type seat Bench type seat Double Cab models Anchor brackets are pro- vided for all rear passenger seats. CrewMax models Anchor brackets are pro- vided for all rear passenger seats.
Page 113 1-7. Safety information Installation with LATCH system (Double Cab models) Type A Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. If the child restraint has a top tether strap, the top tether strap should be latched...
Page 114 1-7. Safety information Type B Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto tether strap anchor. (→P.
Page 115 1-7. Safety information Installation with LATCH system (CrewMax models) If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. (→P. 161) Fold down the seatback and back to the 1st lock position (most upright position) until it locks into place.
Page 116 1-7. Safety information Type A Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the LATCH anchors tighten the lower straps. For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.
Page 117 1-7. Safety information Type B Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the LATCH anchors. For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system. Canada only...
Page 118 1-7. Safety information Installing child restraints using a seat belt (child restraint lock function belt) Rear-facing (Regular Cab models) ⎯ Infant seat/convertible ■ seat Never install a rear-facing child restraint. Your vehicle is not designed to carry an infant. Rear-facing (Double Cab and CrewMax models) ⎯ Infant seat/ ■...
Page 119 1-7. Safety information While pushing the child seat down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
Page 120 1-7. Safety information Fully extend the shoulder belt and then allow it to retract slightly in order to activate the ALR lock mode. Lock mode allows the seat belt to retract only. While pushing the child seat into the seat, allow the shoulder belt to retract until the child seat is securely in place.
Page 121 1-7. Safety information Sit the child in the booster seat. Fit the seat belt to the booster seat according to the manufac- turer’s instructions and insert the plate into the buckle. Make sure that the belt is not twisted. Check that the shoulder belt is correctly positioned over...
Page 122 1-7. Safety information Child restraint systems with a top tether strap (Regular Cab models) Remove the head restraint. Installing position: Right side passenger seat Center passenger seat (Bench type seat) Remove the anchor bracket cover. Installing position: Right side passenger seat Center passenger seat (Bench type seat) Store the removed cover in a safe...
Page 123 1-7. Safety information Center passenger seat (bench type seat) Latch the hook onto the anchor bracket and tighten the top tether strap. Make sure the top tether strap is securely latched. Replace the head restraint. Installing position: Right side passenger seat Center passenger seat (Bench type seat)
Page 124 1-7. Safety information Child restraint systems with a top tether strap (Double Cab models) ■ Right rear seat or center rear seat Raise the head restraints of right and center seats. Pull up the straps of right and center seats.
Page 125 1-7. Safety information Right rear seat Route tether strap through the routing device as shown in the illustration. Make sure the top tether strap is not twisted. Routing device Center rear seat Route tether strap through the routing device as shown in the illustration.
Page 126 1-7. Safety information Center rear seat Latch the hook onto the inner anchor strap ring and tighten the top tether strap. Make sure the top tether strap is securely latched. Inner anchor strap ring Lower the head restraints of right and center seats.
Page 127 1-7. Safety information Pull up the straps of center and left seats. Route tether strap through the routing device as shown in the illustration. Make sure the top tether strap is not twisted. Routing device Latch the hook onto the inner anchor strap ring and tighten the top tether strap.
Page 128 1-7. Safety information Child restraint systems with a top tether strap (CrewMax models) Remove the head restraint. Installing position: Outside passenger seat Center passenger seat Outside passenger seat Swing the seatback forward slightly. (→P. 65) Open anchor bracket cover. Latch the hook onto the anchor bracket.
Page 129 1-7. Safety information Center passenger seat Swing the seatback forward slightly. (→P. 65) Open anchor bracket cover. Latch the hook onto the anchor bracket. Return the seatback to its orig- inal position. Make sure seatback securely locked by pushing for- ward and rearward on the top of the seatback.
Page 130 1-7. Safety information CAUTION ■ When installing a booster seat Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode. (→P. 81) ALR mode causes the belt to tighten only which could cause injury or dis- comfort to the child.
Page 131 1-7. Safety information CAUTION ■ When installing a child restraint system ● Regular Cab models (bench type seat): In order to firmly secure the child restraint system, align the seatback angle and seat position of the right pas- senger seat to match the center pas- senger seat.
Page 132 1-7. Safety information CAUTION ■ When installing a child restraint system ● After securing a child restraint system, never adjust the seat. ● Follow all installation instructions provided by the child restraint system manufacturer. ● After securing the child restraint system, never slide or recline the seat. ■...
Page 133 1-7. Safety information...
Page 134 2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. ■ Starting the engine (→P. 178) ■ Driving With the brake pedal depressed, shift the shift lever to D. (→P. 181) Release the parking brake. (→P.
Page 135 Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down.
Page 136 2-1. Driving procedures ■ Operating your vehicle in a foreign country Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (→P. 671) ■ When turning off the engine In cold climates, or following repeated short trips, emission system operating sounds may continue for a short time after the engine is turned off.
Page 137 If the smell of exhaust is noticed inside the vehicle, open the windows and check that the back window is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately. ●...
Page 138 2-1. Driving procedures CAUTION ■ When driving the vehicle ● Do not adjust the position of the steering wheel, the seat, or the inside or outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents that may result in death or serious injury.
Page 139 2-1. Driving procedures CAUTION ■ When the vehicle is stopped ● Do not race the engine. If the vehicle is in any gear other than P or N, the vehicle may accelerate suddenly and unexpectedly, and may cause an accident. ●...
Page 140 ● Toyota does not recommend occupying the rear cargo area when it is fitted with a slide-in camper, camper shell or other type cover while the engine is running. This caution applies to both driving and stopped or parked situa- tions with the engine running.
Page 141 2-1. Driving procedures CAUTION ■ When taking a nap in the vehicle Always turn the engine off. Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.
Page 142 If you hear a squealing or scraping noise while driving (brake pad wear limit indicators) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. The rotor damage can result if the pads are not replaced when needed.
Page 143 Short in electrical components ● Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. ● Brake function ●...
Page 144 2-1. Driving procedures Engine (ignition) switch ■ Engine switch LOCK The steering wheel is locked and the key can be removed. (The key can be removed only when the shift lever is in P.) Some electrical components such as the audio system can be used.
Page 145 2-1. Driving procedures ■ Turning the key from ACC to LOCK Shift the shift lever to P. (→P. 181) Push in the key and turn to the LOCK position. ■ Steering lock release When starting the engine, the engine switch may seem stuck in the LOCK posi- tion.
Page 146 2-1. Driving procedures NOTICE ■ To prevent battery discharge Do not leave the engine switch in the ACC or ON position for long periods if the engine is not running. ■ When starting the engine ● Do not crank for more than 30 seconds at a time. This may overheat the starter and wiring systems.
Page 147 2-1. Driving procedures Automatic transmission Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever Floor shift type While the engine switch is on, depress the brake pedal and move the shift lever. Column-shift type While the engine switch is on, depress the brake pedal and move the shift lever.
Page 148 2-1. Driving procedures ■ Shift position uses Shift position Function Parking the vehicle or starting the engine Reversing Neutral Normal driving S mode driving : To improve fuel consumption and reduce noises, set the shift lever in D for normal driving. : Selecting shift ranges S mode restricts the upper limit of the possible gear ranges, control engine braking forces, and prevents unneces- sary upshifting.
Page 149 2-1. Driving procedures Column-shift type Upshifting Downshifting The initial shift range in S mode is automatically set to 5 or 4 (6-speed models) or 4 (5-speed models) according to vehicle speed. However, the initial shift range may be set to 3 or 2 (6-speed models) or 3 (5- speed models) if the AI-SHIFT has operated while the shift lever was →...
Page 150 2-1. Driving procedures TOW/HAUL switch (6-speed models with towing package) Use TOW/HAUL mode when pulling a trailer or hauling a heavy load. Floor shift type Press the TOW/HAUL switch. The indicator will come on. Press the switch once more to cancel the mode.
Page 151 If the S indicator does not come on even after shifting the shift lever to This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer, immediately. (In this situation, the vehicle will operate as if the shift lever is in D.) ■...
Page 152 2-1. Driving procedures Turn signal lever Left turn Right turn Move and hold the lever partway to signal a lane change. The left hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change.
Page 153 2-1. Driving procedures Parking brake Sets parking brake*. (Depressing the pedal again releases the parking brake.) U.S.A. Canada At this time, the indicator will come on. *: Fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot.
Page 154 2-1. Driving procedures Horn To sound the horn, press on or close to the mark. ■ After adjusting the steering wheel (manually adjustable type) Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P.
Page 155 2-2. Instrument cluster Gauges and meters Vehicles with multi-information display The following gauges, meters and displays illuminate when the engine switch is in the ON position. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank.
Page 156 2-2. Instrument cluster Multi-information display →P. 200 Automatic transmission fluid temperature gauge Displays the automatic transmission fluid temperature.
Page 157 2-2. Instrument cluster Vehicles without multi-information display (type A) Vehicles without multi-information display (type B) The following gauges, meters and displays illuminate when the engine switch is in the ON position. Tachometer (if equipped) Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed.
Page 158 2-2. Instrument cluster Fuel gauge Displays the quantity of fuel remaining in the tank. Voltmeter (if equipped) Displays the charge state. Engine oil pressure gauge (if equipped) Displays the engine oil pressure. Engine coolant temperature gauge Displays the engine coolant temperature. Odometer/trip meter switching and trip meter resetting button Switches between odometer and trip meter displays.
Page 159 2-2. Instrument cluster Odometer and trip meter display button Pressing this button switches between odometer and trip meter dis- plays. Vehicles with multi-information display Odometer Trip meter A Trip meter B :Pushing and holding the button will reset the trip meter. Vehicles without multi-information display Odometer Trip meter A...
Page 160 While driving ● When the voltmeter indicates more than 19 V or less than 9 V, the battery may be malfunctioning. Have your vehicle checked at your Toyota dealer. ● When the engine oil pressure gauge does not work properly, immediately stop the engine and contact your Toyota dealer.
Page 161 2-2. Instrument cluster Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. ■ Instrument cluster Vehicles with multi-information display Vehicles without multi-information display (type A)
Page 162 2-2. Instrument cluster Vehicles without multi-information display (type B) ■ Center panel...
Page 163 2-2. Instrument cluster ■ Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator Tail light indicator (→P. 186) (→P. 210) (Canada) Headlight high beam AUTO LSD indicator indicator (→P. 212) (→P. 246, 251) Security indicator RSCA OFF indicator (→P.
Page 164 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.
Page 165 Have the vehicle inspected by your Toyota dealer immediately if this occurs.
Page 166 2-2. Instrument cluster ∗ Multi-information display The multi-information display presents the driver with a variety of driving-related data. ● Trip information Displays driving range, fuel consumption and other cruis- ing-related information. ● Warning messages (→P. 619) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.
Page 167 2-2. Instrument cluster Zoom display of odometer and trip meters Displays the odometer and one of the trip meters simultaneously. Average Fuel Economy Displays the average fuel consumption since the function was reset. • The function can be reset by pushing the SELECT RESET button for more than 2 seconds.
Page 168 2-2. Instrument cluster Trip Timer Displays the driving time. To calculate the driving time, press the SELECT RESET button, and to stop the calculation, press it again. To reset the calculation, press the SELECT RESET button for more than 2 seconds. Average Speed Displays the average vehicle speed since the engine was started or the function was reset.
Page 169 2-2. Instrument cluster Feature customization The vehicle can be customized while the vehicle is stopped. Press the SETUP button to select the item you want to cus- tomize unit. UNITS KEYLESS ENTRY FEEDBACK KEYLESS ENTRY RELOCK TIMER KEYLESS ENTRY ALL DOORS UNLOCK DOOR AUTO LOCKING DOOR AUTO UNLOCKING HEADLAMPS AUTO OFF TIMER...
Page 170 2-2. Instrument cluster Press the SELECT RESET button to customize the items. Items Screen text Select in this order To select US (ENGLISH) UNITS US (ENGLISH) METRIC or METRIC (→P. 205) Door lock/ LAMPS + TONE LAMPS KEYLESS ENTRY unlock warning FEEDBACK function TONE...
Page 171 Outside temperature display °F °C on the accessory meter ■ Feature customization error • If SYSTEM ERROR message is indicated, turn the engine switch off and then on again. • If SYSTEM ERROR message is indicated again, contact your Toyota dealer.
Page 172 2-2. Instrument cluster CAUTION ■ Caution while driving Do not adjust the display. Doing so may cause the driver to mishandle the vehicle and an accident, resulting in death or serious injury. NOTICE ■ The multi-information display at low temperatures Allow the interior of the vehicle to warm up before using the liquid crystal information display.
Page 173 2-2. Instrument cluster Accessory meter Outside temperature display (if equipped) Displays the outside air temperature. (→P. 491) Outside temperature and trip information display (if equipped) Displays the outside temperature and trip information. (→P. 208, 491) Clock (→P. 490) H (Hour) button (→P.
Page 174 2-2. Instrument cluster Outside temperature and trip information display (if equipped) Every time the INFO button is pushed, the display toggles through these information. ● OUTSIDE (outside temperature display) Displays the outside air temperature. ● AVG (average fuel consumption after refueling) Displays the average fuel consumption since the vehi- cle was last refueled.
Page 175 2-2. Instrument cluster ● Display off ■ The accessory meter can be operated when The engine switch must be in the ON position. ■ To select the unit A (English/U.S. customary system) or unit B (metric unit) (vehicles without multi-information display) Press the SETUP button to change the units.
Page 176 2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. Type A Vehicles with day- time running light system: The daytime running lights turn side marker, U.S.A Canada parking, tail, license plate, daytime run- ning lights equipped) and instru-...
Page 177 2-3. Operating the lights and wipers Type B Vehicles with day- time running light system: The daytime running lights turn side marker, U.S.A. Canada parking, tail, license plate, daytime run- ning lights equipped) and instru- ment panel lights turn The headlights and all lights listed above (except daytime run- ning lights) turn on.
Page 178 2-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams.
Page 179 2-3. Operating the lights and wipers ■ Guide to dial settings Loading condition Control switch position Towing Regular Cab Double Cab CrewMax Hitch Payload (Towing Standard Long Standard Long Short package) None None Maximum None load Maximum None load ■ Daytime running light system (if equipped) ●...
Page 180 ■ Customization ● That can be configured at Toyota dealer. (vehicles without multi-informa- tion display) Settings (automatic light off system) can be changed. (Customizable features →P. 696) ● It is possible to change the settings. (vehicles with multi-information dis- play) (Feature customization →P.
Page 181 2-3. Operating the lights and wipers ∗ Fog light switch The fog lights improve visibility in difficult driving conditions, such as in rain or fog. Type A ∗ : If equipped...
Page 182 2-3. Operating the lights and wipers Type B ■ The fog lights can be turned on only when The headlights are on low beam.
Page 183 2-3. Operating the lights and wipers Windshield wipers and washer ■ Without intermittent type Type A speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation Washer operation...
Page 184 2-3. Operating the lights and wipers Type B speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation Washer operation...
Page 185 2-3. Operating the lights and wipers ■ Intermittent wiper with interval adjuster Wiper intervals can be adjusted for intermittent operation (when is selected). Type A Intermittent wind- shield wiper opera- tion speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation...
Page 186 2-3. Operating the lights and wipers Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts. Type B Intermittent wind- shield wiper opera- tion speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation...
Page 187 2-3. Operating the lights and wipers Increases the intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts. ■ The windshield wiper and washer can be operated when The engine switch must be in the ON position.
Page 188 Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually. ■ When a windshield washer nozzle becomes blocked Contact your Toyota dealer. Do not try to clear it with a pin or other object. This may damage the nozzle.
Page 189 2-4. Using other driving systems ∗ Cruise control Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicator Cruise control switch ■ Setting the vehicle speed Press the ON-OFF button to activate the cruise control. Cruise control indicator will come on.
Page 190 2-4. Using other driving systems ■ Adjusting the set speed To change the set speed, operate the lever until the desired set speed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction.
Page 191 If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.
Page 192 2-4. Using other driving systems CAUTION ■ To avoid operating the cruise control by mistake Switch the cruise control off using the ON-OFF button when not in use. ■ Situations unsuitable for cruise control Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury.
Page 193 2-4. Using other driving systems ∗ Intuitive parking assist The intuitive parking assist is designed to inform you of the approxi- mate distance between your vehicle and an obstruction by indicator and buzzer when parking the vehicle. This system uses sensors to detect obstructions.
Page 194 2-4. Using other driving systems The distance and buzzer ■ When a sensor detects an obstacle The buzzer sounds. Back sensors Distance Indicator Zone shown as and buzzer in in. (mm) Approximately 70.9 — 45.3 Intermittent (1800 — 1150) Approximately Fast 45.3 —...
Page 195 2-4. Using other driving systems Front corner sensors Distance Indicator Zone shown as and buzzer in in. (mm) Approximately 23.6 — 15.7 Intermittent (600 — 400) Approximately Fast 15.7 — 9.8 intermittent (400 — 250) Approximately Near 9.8 (250) or Continuous less ■...
Page 196 2-4. Using other driving systems Sensors that operate and detection range The following diagrams show the sensor detection range. Note that sensors may not be able to detect obstacles that are extremely close to the vehicle. ■ Detection range of the sensors Back sensors Rear corner sensors Front corner sensors...
Page 197 Objects lower than the sensors or thin stakes etc. may be detected ini- tially, but as they draw closer, they may cease to be detected. • A towing hitch is mounted to the vehicle. • A non-genuine Toyota suspension (lowered suspension etc.) is installed. • When attaching a two-way radio antenna.
Page 198 This ISM device complies with Canadian ICES-001. ■ If the indicator is continuously on Have the vehicle inspected by your Toyota dealer. ■ If the indicator remains blinking but do not sound the buzzer Clean the sensors with soft cloth.
Page 199 2-4. Using other driving systems NOTICE ■ Notes when washing the vehicle Do not apply intensive bursts of water or steam to the sensor area. Doing so may result in the sensor malfunctioning.
Page 200 2-4. Using other driving systems ∗ Rear view monitor system The rear view monitor system assists the driver by displaying an image of the area behind the vehicle. The image is displayed in reverse on the screen. This reversed image is a similar image to the one on the inside rear view mirror.
Page 201 2-4. Using other driving systems ■ The rear view monitor system can be operated when The shift lever is in R and the engine switch is ON. ■ Display mode The rear view monitor display mode can be adjusted when the engine switch is in the ON position and the shift lever is in R.
Page 202 2-4. Using other driving systems ■ Displayed area The area covered by the camera is lim- ited. Objects that are close to either corner of the bumper or under the bumper cannot be seen on the screen. The area displayed on the screen may vary according to vehicle orientation or road conditions.
Page 203 2-4. Using other driving systems ■ Driving precautions When the grade behind the vehicle slopes up sharply, objects appear to be farther away than they actually are. When the grade behind the vehicle slopes down sharply, objects appear to be closer than they actually are.
Page 204 2-4. Using other driving systems The distance that appears on the screen between three-dimensional objects (such as vehicles) and flat surfaces (such as the road) and the actual distance differ as follows. In reality, C = A < B (C and A are equally far away;...
Page 205 2-4. Using other driving systems ■ Rear view monitor system camera The rear view monitor system camera is located on the tailgate as shown in the illustration. In the following cases, it may become dif- ficult to see the images on the screen, even when the system is functioning cor- rectly.
Page 206 Conditions which may affect the rear view monitor system ● If the back of the vehicle has been hit, the camera’s position and mounting angle may have changed. Have the vehicle inspected by your Toyota dealer. ● Rapid temperature changes, such as when hot water is poured on the vehicle in cold weather, may cause the system to function abnormally.
Page 207 When washing the vehicle, do not apply intensive bursts of water to the camera or camera area. Doing so may result in the camera malfunction- ing. ● When replacing the tires, please consult your Toyota dealer. If you replace the tires, the area displayed on the screen may change.
Page 208 2-4. Using other driving systems ∗ Four-wheel drive system Use the front-wheel drive control switch to select the following transfer modes. : Vehicles with multi-information display : Vehicles without multi-information display 2WD (high speed position, two-wheel drive) Normal driving. 4H (high speed position, four-wheel drive) Greater traction than two-wheel drive.
Page 209 2-4. Using other driving systems Shifting between 4H and 4L ■ Shifting from 4H to 4L Stop the vehicle completely. Shift the shift lever to N. Push and turn the front-wheel drive control switch fully clock- wise. Maintain this condition until the 4LO indicator comes on. ■...
Page 210 In this case, you may not be able to shift between 4H and 4L. Have the vehicle inspected by your Toyota dealer immediately. ■...
Page 211 2-4. Using other driving systems CAUTION ■ Caution while driving Never operate the front-wheel drive control switch if the wheels are slipping. Stop the slipping or spinning before shifting. ■ When the vehicle is parked If the shift lever is moved before the 4LO indicator turns on/off, the transfer mode may not be shifted completely.
Page 212 2-4. Using other driving systems AUTO LSD system The AUTO LSD system aids traction by using the traction control system to control engine performance and braking when one of the rear wheels begins to spin. The system should be used only when one of the rear wheels spin- ning occurs in a ditch or rough surface.
Page 213 2-4. Using other driving systems When the AUTO LSD system is operating Vehicles with multi-information display If the rear wheels spin, the slip indicator flashes to indicate that the AUTO LSD system has con- trolled the spinning of the rear wheels.
Page 214 2-4. Using other driving systems CAUTION ■ To avoid an accident ● Do not use the AUTO LSD system in conditions other than the above. A much greater steering effort and more careful cornering control will be required. ● Do not drive with the AUTO LSD system continuously turned on.
Page 215 2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■...
Page 216 2-4. Using other driving systems When VSC/Trailer Sway Control/TRAC/A-TRAC are operating Vehicles with multi-information display If the vehicle is in danger of slip- ping, or if the rear wheels (2WD models and 2WD mode on 4WD models) or all wheels (4WD mode on 4WD models) spin, the slip indicator flashes to indicate that VSC/Trailer Sway Control/...
Page 217 2-4. Using other driving systems To disable VSC, Trailer Sway Control and/or TRAC (2WD models and 2WD mode on 4WD models) If the vehicle gets stuck in fresh snow or mud, VSC, Trailer Sway Control and TRAC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it.
Page 218 2-4. Using other driving systems ■ VSC OFF mode Stop the vehicle completely, and press the VSC OFF switch for more than 3 seconds, when the system is in the AUTO LSD mode. The VSC OFF and TRAC OFF indicators will come on. The system is all off mode.
Page 219 2-4. Using other driving systems ■ VSC OFF mode Stop the vehicle completely, and press the VSC OFF switch for more than 3 seconds. The VSC OFF and TRAC OFF indicators will come on. The system is all off mode. Push the switch again to turn the system back on.
Page 220 ■ When the TRAC OFF indicator light comes on even if the VSC OFF switch has not been pressed TRAC system cannot be operated. Contact your Toyota dealer. ■ Automatic reactivation of TRAC, A-TRAC, VSC and Trailer Sway Con- trol Turning the engine switch off after turning off the TRAC, A-TRAC, VSC and Trailer Sway Control systems will automatically re-enable them.
Page 221 In addition, make sure that the tires are inflated to the appro- priate tire pressure level. The ABS, VSC and Trailer Sway Control will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.
Page 222 2-4. Using other driving systems CAUTION ■ Handling of tires and suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction. ■ Trailer Sway Control precaution The Trailer Sway Control system is not able to reduce trailer sway in all situ- ations.
Page 223 2-5. Driving information Off-road precautions This vehicle has higher ground clearance and narrower tread in rela- tion to the height of its center of gravity to make it capable of per- forming in a wide variety of off-road applications. Off-road vehicle feature ●...
Page 224 2-5. Driving information CAUTION ■ Off-road vehicle precautions Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ● In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Page 225 2-5. Driving information Off-road driving When driving your vehicle off-road, please observe the following pre- cautions to ensure your driving enjoyment and to help prevent the closure of areas to off-road vehicles. ● Drive your vehicle only in areas where off-road vehicles are permit- ted to travel.
Page 226 2-5. Driving information CAUTION ■ Off-road driving precautions Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ● Drive carefully when off the road. Do not take unnecessary risks by driving in dangerous places.
Page 227 2-5. Driving information NOTICE ■ To prevent the water damage ● Take all necessary safety measures to ensure that water damage to the engine or other components does not occur. ● Water entering the engine air intake will cause severe engine damage. ●...
Page 228 2-5. Driving information Cargo and luggage Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the rear deck whenever possible. ● Be sure all items are secured in place. ●...
Page 229 2-5. Driving information (6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Example on your vehicle Cargo capacity Total load capacity...
Page 230 2-5. Driving information CAUTION ■ Things that must not be carried in the luggage compartment The following things may cause a fire if loaded in the luggage compart- ment. ● Receptacles containing gasoline ● Aerosol cans ■ Storage precautions ● Do not stack anything behind the front seats higher than the seat- backs.
Page 231 2-5. Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, TWR (Trailer Weight Rating) and cargo capacity. ■ Total load capacity: (→P. 662) Total load capacity means the combined weight of occupants, cargo and luggage. ■...
Page 232 2-5. Driving information CAUTION ■ Overloading the vehicle Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.
Page 233 2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are appropriate to the prevailing outside tem- peratures.
Page 234 2-5. Driving information ■ When driving the vehicle Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. ■ When parking the vehicle Park the vehicle and move the shift lever to P without setting the parking brake.
Page 235 2-5. Driving information Regulations on the use of snow chains ● Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains. ● Install the chains on the rear tires. ●...
Page 236 NOTICE ■ Repairing or replacing snow tires Request repairs of and obtain replacement snow tires from Toyota deal- ers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the operation of the tire pressure warning valves and transmitters.
Page 237 To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating condi- tions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional...
Page 238 2-5. Driving information Towing related terms ■ GCWR (Gross Combination Weight Rating) The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the cargo in the trailer).
Page 239 2-5. Driving information ■ GAWR (Gross Axle Weight Rating) The maximum allowable gross Front GAWR axle weight. The gross axle weight is the load placed on each axle (front and rear). Rear GAWR ■ TWR (Trailer Weight Rating) The maximum allowable gross (With brakes) trailer weight.
Page 240 2-5. Driving information ■ Unbraked TWR (Unbraked Trailer Weight Rating) The trailer weight rating for tow- (Without brakes) ing a trailer without a trailer ser- vice brake system. ■ Tongue Weight The load placed on the trailer hitch ball. (→P. 281) ■...
Page 241 2-5. Driving information Weight limits ● The gross trailer weight must never exceed the TWR described in the table. (→P. 276, 665) ● The gross combination weight must never exceed the GCWR described in the table. (→P. 276) ● The gross vehicle weight must never exceed the GVWR indi- cated Certification...
Page 242 2-5. Driving information GCWR, TWR, Unbraked TWR, Fifth wheel and Gooseneck towing TWR Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. ■ GCWR and TWR Regular Cab models Driving Model code...
Page 243 2-5. Driving information Driving Model code Engine GCWR system type 14000 lb. 8200 lb. (6350 kg) (3715 kg) 15500 lb. 9700 lb. USK55L-TRTDGA Standard (7030 kg) (4395 kg) 5.7L V8 15000 lb. 9200 lb. (3UR-FBE) *3,4 *3,4 (6800 kg) (4170 kg) engine 14000 lb.
Page 244 2-5. Driving information Driving Model code Engine GCWR system type 14000 lb. 8100 lb. (6350 kg) (3670 kg) USK51L-CRTSKA 16000 lb. 10100 lb. (7255 kg) (4580 kg) Standard 14000 lb. 8100 lb. (6350 kg) (3670 kg) USK51L-CRTLKA 15900 lb. 10000 lb. (7210 kg) (4535 kg) 16000 lb.
Page 245 2-5. Driving information CrewMax models Driving Model code Engine GCWR system type 12500 lb. 6600 lb. (5670 kg) (2990 kg) UPK51L-PSTSKA 14000 lb. 8100 lb. 4.6L V8 (6350 kg) (3670 kg) (1UR-FE) 12500 lb. 6200 lb. engine (5670 kg) (2810 kg) UPK56L-PSTSKA 14000 lb.
Page 246 2-5. Driving information Driving Model code Engine GCWR system type 14000 lb. 7700 lb. (6350 kg) (3490 kg) USK56L-PSTSGA 15300 lb. 9000 lb. 5.7L V8 (6940 kg) (4080 kg) (3UR-FBE) Short 14000 lb. 7700 lb. engine (6350 kg) (3490 kg) USK56L-PSTLGA 15300 lb.
Page 247 2-5. Driving information Trailer Tongue Weight and Trailer Kingpin Weight ● A recommended tongue weight or kingpin weight varies in accor- dance with the types of trailers or towing as described below. ● To ensure the recommended values shown below, the trailer must be loaded by referring to the following instructions.
Page 248 2-5. Driving information 2. Fifth wheel Towing or Gooseneck Towing The gross trailer weight should be distributed so that the kingpin weight is 19% to 21%. (Kingpin weight/Gross trailer weight x 100 = 19% to 21%) Gross trailer weight Kingpin weight The gross trailer weight and kingpin weight can be measured with platform scales found at a highway weighing station, build- ing supply company, trucking company, junk yard, etc.
Page 249 Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight require- ment of your vehicle.
Page 250 2-5. Driving information Selecting trailer ball Use the correct trailer ball for your application. Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers stamped with the required trailer ball size.
Page 251 2-5. Driving information Positions for towing hitch receiver Hitch receiver pin hole posi- tion: 46.4 in. (1179 mm) Connecting trailer lights Use the wire harness stored in the rear end under the vehicle body. 4 pin connector 4 pin, 7 pin connectors...
Page 252 ● Speed limits for towing a trailer vary by state or province. Do not exceed the posted towing speed limit. ● Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest.
Page 253 2-5. Driving information ● Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle-trailer combination. ● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left.
Page 254 2-5. Driving information ● To maintain engine braking efficiency and charging system perfor- mance when using engine braking, do not use the transmission in Transmission shift range position must be in 4 in the S mode. ● Instability happens more frequently when descending steep or long downhill grades.
Page 255 2-5. Driving information ● When restarting after parking on a slope: With the transmission in P, start the engine. Be sure to keep the brake pedal pressed. Shift into D or R (if reversing). Release the parking brake and brake pedal, and slowly pull or back away from the wheel blocks.
Page 256 Break-in schedule If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km).
Page 257 2-5. Driving information ● After the trailer swaying has stopped: • Stop in a safe place. Get all occupants out of the vehicle. • Check the tires of the vehicle and the trailer. • Check the load in the trailer. Make sure the load has not shifted.
Page 258 2-5. Driving information CAUTION ■ To avoid accident or injury ● Do not make jerky, abrupt or sharp turns. ● Do not apply the brakes suddenly as you may skid, resulting in jackknifing and loss of vehicle control. This is especially true on wet or slippery sur- faces.
Page 259 NOTICE ■ When installing a trailer hitch Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage. ■ Do not directly splice trailer lights Do not directly splice trailer lights.
Page 260 2-5. Driving information Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground.
Page 261 2-5. Driving information...
Page 262 3-1. Using the air conditioning system and defogger ∗ Automatic air conditioning system Airflow and outlets are automatically adjusted according to the tem- perature setting. Control panel Windshield defogger Air outlet selection dial Driver’s side temperature control dial Front passenger’s Air conditioning ON/OFF switch side temperature control dial...
Page 263 3-1. Using the air conditioning system and defogger Display Fan speed display Airflow display Front passenger’s side Driver’s side temperature temperature setting display setting display Using the automatic mode Press The air conditioning system will begin to operate. Air outlets and fan speed are automatically adjusted according to the temperature set- ting.
Page 264 3-1. Using the air conditioning system and defogger Adjusting the settings ■ Adjusting the temperature setting Turn the temperature control dial clockwise (warm) or counter- clockwise (cool). The air conditioning system switches between individual and simultaneous modes each time is pressed. ●...
Page 265 3-1. Using the air conditioning system and defogger ■ Changing the air outlets Turn the air outlet selection dial. The air outlets switch each time either side of air outlet selection dial is turned. Air flow as shown according to the mode selected. When the dial is set to , air flows to the upper body.
Page 266 3-1. Using the air conditioning system and defogger When the dial is set to , air flows to the feet. : Double Cab and CrewMax models only : CrewMax models only When the dial is set to , air flows to the feet and the wind- shield defogger operates.
Page 267 3-1. Using the air conditioning system and defogger Defogging the windshield Press The indicator comes on. The air conditioning system con- trol operates automatically. Recirculated air mode will auto- matically switch to outside air mode. Adjusting the position and opening and closing the air outlets Driver side outlets Direct air flow to the left or right, up or down.
Page 268 3-1. Using the air conditioning system and defogger Front passenger side outlets Direct air flow to the left or right, up or down. Turn the knob to open or close the vent. Rear outlets (CrewMax models only) Direct air flow to the left or right, up or down.
Page 269 There may be a problem in the air conditioning system if the indi- cator continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer. ■ Air conditioning odors ●...
Page 270 3-1. Using the air conditioning system and defogger • The start timing of the blower may be delayed for a short period of time immediately after the air conditioning system is started in automatic mode. CAUTION ■ To prevent the windshield from fogging up Do not use during cool air operation in extremely humid weather.
Page 271 3-1. Using the air conditioning system and defogger ∗ Manual air conditioning system Air conditioning ON/OFF switch Outside air or recirculated Driver’s side temperature air mode control dial Front passenger’s side temperature control dial Fan speed control dial Air outlet selection dial Adjusting the settings ■...
Page 272 3-1. Using the air conditioning system and defogger Front passenger’s side temperature control dial Turn the temperature control dial clockwise (warm) or counter- clockwise (cool). ● Individual mode When the front passenger’s side temperature control dial in a posi- tion other than the SYNC position, the temperature for the driver and front passenger seats can be adjusted separately.
Page 273 3-1. Using the air conditioning system and defogger Air flow as shown according to the mode selected. When the dial is set to , air flows to the upper body. : CrewMax models only When the dial is set to , air flows to the upper body and feet.
Page 274 3-1. Using the air conditioning system and defogger When the dial is set to , air flows to the feet and the wind- shield defogger operates. The air intake selector is automat- ically set to outside air mode. To return the recirculated air mode, press : Double Cab and CrewMax models only : CrewMax models only...
Page 275 3-1. Using the air conditioning system and defogger ■ If the ambient temperature drops while using the recirculated air mode The air intake mode automatically changes from recirculated air mode to outside air mode after a few minutes. To cancel this function: Press and hold for longer than 2 seconds.
Page 276 3-1. Using the air conditioning system and defogger Front passenger side outlets Direct air flow to the left or right, up or down. Turn the knob to open or close the vent. Rear outlets (CrewMax models only) Direct air flow to the left or right, up or down.
Page 277 There may be a problem in the air conditioning system if the indi- cator continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer. ■ Air conditioning odors ●...
Page 278 3-1. Using the air conditioning system and defogger CAUTION ■ To prevent the windshield from fogging up Do not set the air outlet selection dial to during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.
Page 279 3-1. Using the air conditioning system and defogger Outside rear view mirror defoggers and front windshield wiper de-icer (if equipped on Regular Cab and Double Cab models) Clear the outside rear view mirrors using the defogger. Vehicles with an automatic air conditioning system On/off Press the button to turn on the outside rear view mirror defog-...
Page 280 3-1. Using the air conditioning system and defogger Vehicles with a manual air conditioning system On/off Press the button to turn on the outside rear view mirror defog- gers. The indicator will come on. The defoggers will auto- matically turn off after about 15 minutes.
Page 281 3-1. Using the air conditioning system and defogger Back window, outside rear view mirror defoggers and front windshield wiper de-icer (if equipped on CrewMax models) Clear the back window using the defogger. Vehicles with an automatic air conditioning system On/off Press the button to turn on the back window defogger.
Page 282 3-1. Using the air conditioning system and defogger Vehicles with a manual air conditioning system On/off Press the button to turn on the back window defogger. The indicator will come on. The defoggers will automatically turn off after about 15 minutes. Pressing the button again also turns the defogger off.
Page 283 3-1. Using the air conditioning system and defogger CAUTION ■ Back window defogger The surface of the back window becomes hot. Do not touch it to prevent from burning yourself. ■ Outside rear view mirror defoggers (if equipped) The surfaces of the outside rear view mirrors become hot. Do not touch them to prevent from burning yourself.
Page 284 3-2. Using the audio system Audio system types With navigation system Owners of models equipped with a navigation system should refer to the “Navigation System Owner’s Manual”. Without navigation system Type A: CD player with changer controller and AM/FM radio Type B: CD player with changer and AM/FM radio...
Page 285 3-2. Using the audio system Type C: CD player with changer controller and AM/FM radio Title Page Using the radio P. 324 Using the CD player P. 332 Playing MP3 and WMA discs P. 341 Operating an iPod P. 349 Operating a USB memory P.
Page 286 3-2. Using the audio system Language settings (type B and C) The language used for all voice guidance, voice recognition and mes- sages may be changed. Press Press that corresponds to “MORE”. Press that corresponds to “LANG”. Press that corresponds to the desired language. For vehicles sold in the U.S.A.
Page 287 3-2. Using the audio system CAUTION ■ For vehicles sold in U.S.A. and Canada ● Part 15 of the FCC Rules FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device. ●...
Page 288 3-2. Using the audio system Using the radio Type A Power Volume Station selector Changing Seeking the the channel frequency Displaying radio text Adjusting the messages frequency (AM, FM mode) or channel AM⋅SAT/FM Scanning for (SAT mode) mode buttons receivable stations Type B and C Power Volume...
Page 289 3-2. Using the audio system ® Setting station presets (excluding XM Satellite Radio) Search for desired stations by turning ∧ pressing “∨” or “ ” on Press and hold a button (from or one of until you hear a beep. Type B and C: Each time is pressed, station pages are changed.
Page 290 3-2. Using the audio system ■ Displaying radio text messages (for type B and C, FM mode only) When a new radio text message is received, “MSG” is shown on the display. To display the message, press If the text continues past the end of the display, “ ”...
Page 291 3-2. Using the audio system ■ ® Setting XM Satellite Radio channel presets Select the desired channel. Press and hold a button (from or one of ) until you hear a beep. Type B and C: Each time is pressed, station pages are changed. There are a total of 6 pages.
Page 292 3-2. Using the audio system ■ Displaying text information Press Each time is pressed, the display changes in the following order: Type A Channel name → Title (song/program title) → Name (artist name/feature) → Channel number. Type B and C Title (song/program title) →...
Page 293 3-2. Using the audio system ■ When the battery is disconnected All preset stations are erased. (type A only) ■ Reception sensitivity ● Objects, especially metal objects, such as cargo, a camper, or a truck ® rack, may adversely affect the reception of XM Satellite Radio.
Page 294 ANTENNA securely. CHECK There is a short-circuit in the antenna or the sur- ANTENNA rounding antenna cable. See a Toyota certified dealer. ® You have not subscribed to XM Satellite Radio. The radio is being updated with the latest encryp- ®...
Page 295 3-2. Using the audio system The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel. ® Contact the XM Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877- 209-0079 (Canada) ■...
Page 296 3-2. Using the audio system Using the CD player Type A Power Volume Random playback Repeat play Reverse Fast-forward CD eject Selecting Playback Displaying text a track messages Searching playback Type B and C Power Volume CD eject Selector buttons CD load (type B only) Fast-forwarding...
Page 297 3-2. Using the audio system Loading CDs ■ Loading a CD (type A and C) Insert a CD. ■ Loading a CD (type B) Press When the indicator on the slot turns from amber to green, insert a CD. ■ Loading multiple CDs (type B only) Press and hold until you hear a beep.
Page 298 3-2. Using the audio system Ejecting CDs ■ Ejecting a CD (type A and C) Press and remove the CD. ■ Ejecting a CD (type B) To select the CD to be ejected, press that corre- sponds to “ ” or “ ”.
Page 299 3-2. Using the audio system Scanning tracks Press The first ten seconds of each track will be played. To cancel, press again. Press again when the desired track is reached. Selecting a CD (type B only) ■ Selecting a CD to play Press that corresponds to “...
Page 300 3-2. Using the audio system Random playback ■ Current CD Press that corresponds to “RDM”. Songs are played in random order. To cancel, press the button again. ■ All CDs (type B only) Press that corresponds to “RDM” twice. Tracks on all loaded CDs are played in random order. To cancel, press the button again.
Page 301 3-2. Using the audio system Switching the display Press Each time is pressed, the display changes in the following order: Type A Track no./Elapsed time → CD title → Track name. Type B and C Track title → Track name/Artist name → Track name/Elapsed time. ■...
Page 302 “WAIT” or “PLEASE WAIT”: Operation has stopped due to a high tempera- ture inside the player. Wait for a while and then press . Contact your Toyota dealer if the CD still cannot be played back. ■ Discs that can be used Discs with the marks shown below can be used.
Page 303 3-2. Using the audio system NOTICE ■ CDs and adapters that cannot be used Do not use the following types of CDs, 3 in. (8 cm) CD adapters or Dual Discs. Doing so may damage the CD player and/or the CD insert/eject function. ●...
Page 304 3-2. Using the audio system NOTICE ■ CD player precautions Failure to follow the precautions below may result in serious damage to the CDs or the player itself. ● Do not insert anything other than CDs into the CD slot. ●...
Page 305 3-2. Using the audio system Playing MP3 and WMA discs Type A Power Volume Reversing Fast-forwarding CD eject Selecting a folder Selecting a file Displaying text messages Random playback Searching playback Repeat play Playback Type B and C Power Volume Selector buttons CD eject CD load...
Page 306 3-2. Using the audio system Loading and ejecting MP3 and WMA discs →P. 333 Selecting MP3 and WMA discs (type B only) →P. 335 Selecting and scanning a folder ■ Selecting folders one at a time Press “∨” or “∧” on to select the desired folder.
Page 307 3-2. Using the audio system ■ Selecting the desired file by cueing the files in the folder Press When the desired file is reached, press once again. Fast-forwarding and reversing files Type A Press Type B and C ∧ Press and hold “∨” or “ ”...
Page 308 3-2. Using the audio system Repeat play ■ Repeating a file Press that corresponds to “RPT”. To cancel, press the button again. ■ Repeating all of the files in a folder Type A Press and hold until you hear a beep. To cancel, press the button again.
Page 309 “WAIT” or “PLEASE WAIT”:Operation has stopped due to a high tempera- ture inside the player. Wait for a while and then press . Contact your Toyota dealer if the CD still cannot be played. ■ Discs that can be used →P.
Page 310 3-2. Using the audio system ■ MP3 and WMA files MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression. ® WMA (Windows Media Audio) is a Microsoft audio compression format.
Page 311 3-2. Using the audio system ● Compatible media Media that can be used for MP3 and WMA playback are CD-Rs and CD- RWs. Playback in some instances may not be possible, depending on the status of the CD-R or CD-RW. Playback may not be possible or the audio may jump if the disc is scratched or marked with fingerprints.
Page 312 3-2. Using the audio system ● MP3 and WMA playback When a disc containing MP3 or WMA files is inserted, all files on the disc are first checked. Once the file check is finished, the first MP3 or WMA file is played.
Page 313 3-2. Using the audio system ∗ Operating an iPod Connecting an iPod enables you to enjoy music from the vehicle speakers. ■ Connecting an iPod Open the cover and connect an iPod using an iPod cable. Turn on the power of the iPod if it is not turned on.
Page 314 3-2. Using the audio system Selecting a play mode Press that corresponds to “BROWSE” to select iPod menu mode. Press that corresponds to the desired play mode. ■ Play mode list First Second Third Fourth Play mode selection selection selection selection Playlist Songs...
Page 315 3-2. Using the audio system ■ Selecting a list Turn to display the first selection list. Press to select the desired item. Pressing that corresponds to “MORE” changes to the second selection list. Repeat the same procedure to select the desired song name. To return to the previous selection list, press that corresponds to “...
Page 316 3-2. Using the audio system Selecting songs Turn or press “∨” or “∧” on to select the desired song. Playing and pausing songs Press Fast-forwarding and reversing songs ∧ Press and hold “∨” or “ ” on Shuffle playback ■ Playing songs from one playlist or album in random order Press that corresponds to “RDM”.
Page 317 3-2. Using the audio system Switching the display Press Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time ■ About iPod ● Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Page 318 3-2. Using the audio system ■ Compatible models Model Generation Software version iPod 5th generation Ver. 1.2.0 or higher iPod nano 1st generation Ver. 1.3.0 or higher 2nd generation Ver. 1.1.2 or higher 3rd generation Ver. 1.0.0 or higher iPod touch 1st generation Ver.
Page 319 3-2. Using the audio system ∗ Operating a USB memory Connecting a USB memory enables you to enjoy music from the vehicle speakers. ■ Connecting a USB memory Open the cover and connect a USB memory. Turn on the power of the USB memory if it is not turned on.
Page 320 3-2. Using the audio system Selecting and scanning a folder ■ Selecting a folder Press “∨” or “∧” on to select the desired folder. ■ Returning to the first file of the first folder Press and hold “∨” on until you hear a beep. ■...
Page 321 3-2. Using the audio system Playing and pausing files Press Fast-forwarding and reversing files ∧ Press and hold “∨” or “ ” on Random playback ■ Playing files from a folder in random order Press that corresponds to “RDM”. To cancel, press the button twice. ■...
Page 322 3-2. Using the audio system Switching the display Press Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time ■ USB memory functions Depending on the USB memory that is connected to the system, certain functions may not be available.
Page 323 3-2. Using the audio system ■ USB memory ● Compatible device USB memory that can be used for MP3 and WMA playback. Depending on the type of USB device, playback may not be possible. ● Compatible device formats The following device formats can be used: •...
Page 324 3-2. Using the audio system ● MP3 file compatibility • Compatible standards MP3 (MPEG1 AUDIO LAYERII, III, MPEG2 AUDIO LAYERII, III, MPEG2.5) • Compatible sampling frequencies MPEG1 AUDIO LAYERII, III: 32, 44.1, 48 (kHz) MPEG2 AUDIO LAYERII, III: 16, 22.05, 24 (kHz) MPEG2.5: 8, 11.025, 12 (kHz) •...
Page 325 3-2. Using the audio system ● Extensions If the file extensions .mp3 and .wma are used for files other than MP3 and WMA files, they will be mistakenly recognized and played as MP3 and WMA files. This may result in large amounts of interference and damage to the speakers.
Page 326 3-2. Using the audio system Optimal use of the audio system Type A Adjusting the sound quality and ASL Type B and C Menu button Selector buttons Selector knob...
Page 327 3-2. Using the audio system Using the audio control function ■ Changing sound quality modes Type A Pressing selects the mode to be changed in the following order: “BAS”→“TRE”→“FAD”→“BAL”→“ASL” Type B and C Press Press that corresponds to the desired mode. “BASS”, “MID”...
Page 328 3-2. Using the audio system Type B and C Turning adjusts the level. Mode Sound qual- Turn to the Turn to the Level displayed ity mode left right BASS Bass* -5 to 5 Mid-range* -5 to 5 High (type B only) TREB Treble* -5 to 5...
Page 329 3-2. Using the audio system Type B and C Press Press that corresponds to “MORE”. Press that corresponds to “ASL”. Press that corresponds to the desired mode. Type B: “ON” or “OFF” Type C: “LOW”, “MID”, “HIGH”, or “OFF” ASL automatically adjusts the volume and tone quality according to vehicle speed.
Page 330 3-2. Using the audio system ∗ Using the AUX port This port can be used to connect a portable audio device and listen to it through the vehicle’s speakers. Open the cover and connect the portable audio device. Type A Type B and C Press ∗...
Page 331 3-2. Using the audio system ■ Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle’s audio controls. All other adjustments must be made on the portable audio device itself. ■ When using a portable audio device connected to the power outlet Noise may occur during playback.
Page 332 3-2. Using the audio system ∗ Using the steering wheel audio switches Some audio features can be controlled using the switches on the steering wheel. Increases/decreases vol- Radio mode: Selects radio station CD mode: Selects track/file, folder and disc iPod mode: Selects a song memory mode: Selects a file and folder...
Page 333 3-2. Using the audio system Turning the power on Press when the audio system is turned off. The audio system can be turned off by holding the switch down until you hear a beep. Changing the audio source Press when the audio system is turned on. The audio source changes as follows each time the switch is pressed.
Page 334 3-2. Using the audio system Selecting a track/file or song ® Press to select the CD, iPod, USB memory, Bluetooth audio or RSE mode. Press “∨” or “∧” on to select the desired track/file or song. Selecting a folder or album ®...
Page 335 3-2. Using the audio system Antenna The antenna can be removed. ■ Removing the antenna Place the included wrench around the antenna. When not in use, the wrench is stored in glove box. Loosen the antenna with the wrench and remove it.
Page 336 3-2. Using the audio system ■ Installing the antenna Tighten the antenna by one hand until it will not turn any more. Using the wrench, tighten the antenna an additional 1/8th turn (20 to 45 degrees) to secure it in place. After tightening the antenna, remove the wrench.
Page 337 3-2. Using the audio system NOTICE ■ To avoid damaging the antenna Remove the antenna in the following situations. ● When using an automatic carwash. ● When the antenna will touch the ceiling of a garage, etc. ● When covering the vehicle with a car cover. ■...
Page 338 ® 3-3. Using the Bluetooth audio system ® ∗ Bluetooth audio system ® The Bluetooth audio system enables you to enjoy music played on a portable digital audio player (portable player) from the vehicle speakers via wireless communication. ® This audio system supports Bluetooth , a wireless data system capable of playing portable audio music without cables.
Page 339 ® 3-3. Using the Bluetooth audio system ■ When transferring ownership of the vehicle Be sure to initialize the system to prevent personal data from being improp- erly accessed. (→P. 448) ■ ® About Bluetooth Bluetooth is a registered trademark of Bluetooth SIG.
Page 340 ® 3-3. Using the Bluetooth audio system CAUTION ■ FCC WARNING Changes or modifications in construction not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio frequency exposure. This device is approved for Mobile Application only and, to comply with applicable FCC radio frequency exposure regula- tions, must be used with a distance of at least 7.9 in.
Page 341 ® 3-3. Using the Bluetooth audio system ® Using the Bluetooth audio system ■ Audio unit Display A message, name, number, etc. is displayed. Lower-case characters and special characters cannot be displayed. Displays information that is too long to be displayed at one time on the display (press and hold) Selects items such as menu...
Page 342 ® 3-3. Using the Bluetooth audio system Operating the system using voice commands By following the voice guidance instructions output from the speaker, ® voice commands enable the operation of the Bluetooth audio sys- tem without the need to check the display or operate ■...
Page 343 ® 3-3. Using the Bluetooth audio system ® Using the Bluetooth audio system for the first time ® Before using the Bluetooth audio system, it is necessary to register ® a Bluetooth enabled portable player in the system. Follow the proce- dure below to register (pair) a portable player: Press until “BT AUDIO”...
Page 344 ® 3-3. Using the Bluetooth audio system ® Menu list of the Bluetooth audio system ■ Normal operation First Second Third menu Operation detail menu menu “Pair Audio Player” Registering a portable player “Select Audio Selecting a portable player to Player”...
Page 345 ® 3-3. Using the Bluetooth audio system ■ When using a voice command For numbers, say a combination of single digits from zero to nine. Say the command correctly and clearly. ■ The system may not recognize your voice in the following situations: ●...
Page 346 ® 3-3. Using the Bluetooth audio system ® Operating a Bluetooth enabled portable player Power Volume Selecting an album Selector buttons Fast-forwarding Playback/pause and reversing/ Displaying text messages Selecting a track Selecting a track Playback Selecting an album Press “∨” or “∧” on Selecting tracks Turn or press “∨”...
Page 347 ® 3-3. Using the Bluetooth audio system Fast-forwarding and reversing tracks ∧ Press and hold “∨” or “ ” on Switching the display Press Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time Using the steering wheel audio switches →P.
Page 348 ® 3-3. Using the Bluetooth audio system ® Setting up a Bluetooth enabled portable player ® Registering a portable player in the Bluetooth audio system allows the system to function. The following functions can be used for reg- istered portable players: ■...
Page 349 ® 3-3. Using the Bluetooth audio system Selecting a portable player to be used Select “Select Audio Player” using a voice command or Select the portable player to be used by either of the following methods, and select “Confirm” by using a voice command or a.
Page 350 ® 3-3. Using the Bluetooth audio system Changing the registered name of a portable player Select “Change Name” using a voice command or Select the name of the portable player to be changed by either of the following methods, and select “Confirm” using a voice command or a.
Page 351 ® 3-3. Using the Bluetooth audio system Changing the passkey Select “Set Passkey” using a voice command or Press the talk switch, say a 4 to 8-digit number, and select “Confirm” using a voice command or When the entire number to be registered as a passkey has been input, press again.
Page 352 ® 3-3. Using the Bluetooth audio system ■ The number of portable players that can be registered Up to 2 portable players can be registered in the system.
Page 353 ® 3-3. Using the Bluetooth audio system ® Bluetooth audio system setup ■ System setup items and operation procedures ● Setting voice guidance volume 1. “Setup” → 2. “System Setup” → 3. “Guidance Volume” (→P. 447) ® ● Displaying the Bluetooth device address and name 1.
Page 354 3-4. Using the rear audio/video system ∗ Rear seat entertainment system The rear seat entertainment system is designed for the rear passen- gers to enjoy audio and DVD video separately from the front audio system. Front separated type seats Front audio system DVD player Display Rear seat entertainment system remote controller...
Page 355 3-4. Using the rear audio/video system Front bench type seat Front audio system DVD player Display Rear seat entertainment system remote controller Power outlet A/V input port...
Page 356 3-4. Using the rear audio/video system Opening and closing the display Press the lock release button to open the display. Pull the display down to an easily viewable angle (between 90° and 125°). To close the display, push the display up until a click is heard. The illumination of the screen is automatically turned off when the display is closed.
Page 357 3-4. Using the rear audio/video system Ejecting a disc Press and remove the disc. Turning the rear seat entertainment system power on/off ■ Operating from the front audio system Selecting either the front audio system or DVD player audio for the speakers Press that corresponds to “OFF”, to turn off the rear...
Page 358 3-4. Using the rear audio/video system Setting the rear seat entertainment system lock Front audio system Selecting either the front audio system or DVD player audio for the speakers Selecting “LOCK” “UNLOCK” for the rear seat entertainment system The rear seat entertainment sys- tem lock remains on, even when the engine switch is turned off.
Page 359 “REGION CODE ERROR”:Indicates that the DVD region code is not set properly. “DVD ERROR”: Indicates that there is a problem inside the player. Eject the disc. Set the disc again. If the malfunction still exists, take the vehicle to your Toyota dealer.
Page 360 ● The operational range is reduced. ■ When replacing the AA batteries Batteries can be purchased at your Toyota dealer, electric appliance shop, or camera stores. Replace only with the same or equivalent type recommended by a Toyota dealer. Dispose of used batteries according to local laws.
Page 361 3-4. Using the rear audio/video system ■ Headphones With some headphones generally available in the market, sound quality may be poor. Toyota recommends the use of Toyota genuine wireless head- phones. Please contact your Toyota dealer for further details. ■...
Page 362 3-4. Using the rear audio/video system NOTICE ■ For normal operation after replacing the batteries Observe the following precautions to prevent accidents. ● Always work with dry hands. Moisture may cause the battery to rust. ● Do not touch or move any other components inside the remote controller. ●...
Page 363 3-4. Using the rear audio/video system Using the DVD player (DVD video) ■ Remote controller Turning on the DVD mode Turning on/off the control icon screen Selecting a chapter Reversing a disc Turning on the menu screen Turning on the title selection screen Searching the title Changing the screen angle...
Page 364 3-4. Using the rear audio/video system ■ Unit Ejecting a disc Turning on the DVD mode Skipping to the desired chapter Playing/pausing a disc Turning on/off the control icon screen Selecting a control icon Inputting the selected con- trol icon...
Page 365 3-4. Using the rear audio/video system ■ Control icon screen (Page1) Turning off the control icon screen on the screen Displaying control icon screen page 2 Turning on/off title selection screen for the disc Turning on/off the menu screen for the disc Reversing a disc Stopping a disc Playing/pausing a disc...
Page 366 3-4. Using the rear audio/video system ■ Operating from the front audio system Press: Selecting a chapter Press and hold: Fast-for- warding/reversing a disc Stopping/playing a disc Selecting the DVD mode Starting a disc Displaying a elapsed time Playing/pausing a disc NOTICE ■...
Page 367 3-4. Using the rear audio/video system Turning on the title selection screen Press or select to turn on the title selection screen. For the operation of the title selection screen, see the separate manual for the DVD disc. Turning on the menu screen Press or select to turn on the menu screen.
Page 368 3-4. Using the rear audio/video system Changing the subtitle language Press or select display the subtitle language screen. Each time is pressed or is selected, another lan- guage stored on the disc is selected. Select to return to the pre- vious screen.
Page 369 3-4. Using the rear audio/video system Changing the angle Press or select display the screen to change the angle. Each time is pressed or is selected, the angle changes. Select to return to the pre- vious screen. ■ DVD player and DVD video discs This DVD player is compatible with NTSC color TV formats.
Page 370 3-4. Using the rear audio/video system ■ Marks shown on DVD video discs Indicates NTSC format of color TV. Indicates the number of audio tracks. Indicates the number of language subtitles. Indicates the number of angles. Indicates the screen to be selected. Wide screen: 16:9 Standard: 4:3 Indicates regions in which this video disc can...
Page 371 3-4. Using the rear audio/video system ● Multi-angle feature: Allows you to enjoy the same scene at different angles. ● Multi-language feature: Allows you to select the language of the subtitles and audio. ● Region codes: Region codes are provided on DVD players and DVD discs.
Page 372 3-4. Using the rear audio/video system Using the DVD player (video CD) ■ Remote controller Turning on the DVD mode Turning on/off the control icon screen Selecting a chapter Reversing a disc Searching the disc menu number Inputting the selected con- trol icon Turning off the screen Selecting a control icon...
Page 373 3-4. Using the rear audio/video system ■ Control icon screen (Page1) Selecting a disc menu num- Turning off the menu screen Displaying control icon screen page 2 Turning on the disc menu Returning to the previous page screen (with the disc menu displayed) Proceeding to the next page screen (with the disc menu...
Page 374 3-4. Using the rear audio/video system ■ Operating from the front audio system Press: Selecting a chapter Press and hold: Fast-for- warding/reversing a disc Stopping/playing a disc Selecting the DVD mode Starting a disc Displaying a elapsed time Playing/pausing a disc Selecting a disc menu number Select to display the disc menu number search screen.
Page 375 3-4. Using the rear audio/video system Using the DVD player (audio CD/CD text) ■ Control screen Press to dis- play the control screen. Repeat play Random playback Search playback ■ Operating from the front audio system Press: Selecting a track Press and hold: Fast-for- warding/reversing a disc Selecting the DVD mode...
Page 376 3-4. Using the rear audio/video system Search playback ■ Scanning tracks Select The first 10 seconds of each track will be played. Select again when the desired track is reached. ■ Canceling repeat play and random playback Select once again.
Page 377 3-4. Using the rear audio/video system Using the DVD player (MP3 discs) ■ Control screen Press to dis- play the control screen. Repeat play Random playback Search playback Displaying file information Selecting a folder ■ Operating from the front audio system Press: Selecting a file Press and hold: Fast-for- warding/reversing a file...
Page 378 3-4. Using the rear audio/video system Random playback ■ Playing files from a particular folder in random order Select ■ Playing all of the files on a disc in random order Select , and press and hold Selecting and scanning folders ■...
Page 379 3-4. Using the rear audio/video system ■ Canceling repeat play and random playback Select once again.
Page 380 3-4. Using the rear audio/video system Using the video mode Press to select the video mode. Before switching to the video mode, connect audio source to the A/V input port. Using the A/V input port Front separated type seats Open the cover. The A/V input port is composed of 3 input ports.
Page 381 3-4. Using the rear audio/video system ■ A/V input port The rear seat entertainment system plays videos and sound when audio- visual equipment is connected to the A/V input port. For details, refer to the manufacturer’s instructions. ■ Power outlet The power outlet can be used to connect the audio-visual device.
Page 382 3-4. Using the rear audio/video system Changing the Setup Menu settings Press or select display initial setting screen. The following settings can be customized here. ● Audio language ● Subtitle language ● DVD language ● Angle mark ● Parental lock Changing the audio language Select Select the language you want to...
Page 383 3-4. Using the rear audio/video system Select if you cannot find the language you would like to hear. Enter the appropriate 4-digit lan- guage code. (→P. 423) Select a number, and press to input it. If a code that is not in the list is entered, “Incorrect Code”...
Page 384 3-4. Using the rear audio/video system Changing the DVD language Select Select the language you would like to hear and press to input it. Select if you cannot find the language you would like to hear. Enter the appropriate 4-digit lan- guage code.
Page 385 3-4. Using the rear audio/video system Setting viewer restriction levels Setting a personal code allows the viewer restriction to be used. Select Enter a personal code and press The setting cannot be changed unless personal code entered. When you forget a personal code, initialize a personal code.
Page 386 3-4. Using the rear audio/video system Setting the display mode Pressing changes the dis- play mode sequentially as fol- lows: Normal → Wide 1 → Wide 2 Returning to the previous screen Select to return to the previous screen.
Page 387 3-4. Using the rear audio/video system ■ To initialize the password Press on the remote controller or unit ten times when the Enter Personal Code screen is displayed. ■ Language code list Code Language Code Language 0514 English 0208 Bihari 0618 French 0209...
Page 388 3-4. Using the rear audio/video system Code Language Code Language 0721 Gujarati 1311 Macedonian 0801 Hausa 1312 Malayalam 0809 Hindi 1314 Mongolian 0818 Croatian 1315 Moldavian 0821 Hungarian 1318 Marathi 0825 Armenian 1319 Malay 0901 Interlingua 1320 Maltese 0905 Interlingue 1325 Burmese 0911...
Page 389 3-4. Using the rear audio/video system Code Language Code Language 1914 Shona 2014 Setswana 1915 Somali 2015 Tonga 1917 Albanian 2018 Turkish 1918 Serbian 2019 Tsonga 1919 Siswati 2020 Tatar 1920 Sesotho 2023 1921 Sundanese 2111 Ukrainian 1923 Swahili 2118 Urdu 2001 Tamil...
Page 390 3-5. Using the hands-free phone system (for cellular phone) ∗ Hands-free phone system (for cellular phone) features ® This system supports Bluetooth , which allows you to make or receive calls without using cables to connect a cellular phone and the system, and without operating the cellular phone.
Page 391 3-5. Using the hands-free phone system (for cellular phone) Title Page Using the hands-free phone system ■ Operating the system by using a voice command ■ Using the hands-free system for the P. 430 first time ■ Menu list of the hands-free phone sys- Making a phone call ■...
Page 392 ● OPP (Object Push Profile) Ver. 1.1 ■ For detailed information about Handsfree Phone System For assistance with pairing and operating your cell phone, go to the website www.toyota.letstalk.com. ® ■ About Bluetooth Bluetooth is a registered trademark of Bluetooth SIG. Inc.
Page 393 3-5. Using the hands-free phone system (for cellular phone) CAUTION ■ FCC WARNING Changes or modifications in construction not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio frequency exposure. This device is approved for Mobile Application only and, to comply with applicable FCC radio frequency exposure regula- tions, must be used with a distance of at least 7.9 in.
Page 394 3-5. Using the hands-free phone system (for cellular phone) Using the hands-free phone system ■ Audio unit Display A message, name, phone number, etc. is displayed. Lower-case characters and special characters, such as an umlaut, cannot be dis- played. Displays information that is too long to be displayed at one time on the display (press and hold)
Page 395 3-5. Using the hands-free phone system (for cellular phone) ■ Steering wheel Volume The voice guidance volume cannot be adjusted using this button. On-hook switch Turns the hands-free sys- tem off/ends a call/refuses a call Off-hook switch Turns the hands-free sys- tem on/starts a call Talk switch Turns the voice command...
Page 396 3-5. Using the hands-free phone system (for cellular phone) Operating the system by using a voice command By following the voice guidance instructions output from the speaker, voice commands enable the operation of the hands-free phone sys- tem without the need to check the display or operate ■...
Page 397 3-5. Using the hands-free phone system (for cellular phone) Register a phone name by either of the following methods. a. Select “Record Name” by using , and say a name to be registered. b. Press the talk switch and say a name to be registered. A voice guidance instruction to confirm the input is heard.
Page 398 3-5. Using the hands-free phone system (for cellular phone) Menu list of the hands-free phone system ■ Normal operation Second First menu Third menu Operation detail menu Dialing a number stored in the “Callback” incoming call history memory Dialing a number stored in the “Redial”...
Page 399 3-5. Using the hands-free phone system (for cellular phone) Second First menu Third menu Operation detail menu “Set PIN” Setting a PIN code “Phone- Locking the phone book book Lock” “Security” “Phone- book Unlocking the phone book Unlock” “Pair Registering the cellular phone Phone”...
Page 400 3-5. Using the hands-free phone system (for cellular phone) ■ Using a short cut key First menu Second menu Operation detail Dialing a number registered “Dial XXX (name)” in the phone book “Dial XXX (number)” Dialing the input numbers “Phone book add Adding a new number entry”...
Page 401 3-5. Using the hands-free phone system (for cellular phone) ■ Automatic volume adjustment When vehicle speed is 50 mph (80 km/h) or more, the volume automatically increases. The volume returns to the previous volume setting when vehicle speed drops to 43 mph (70 km/h) or less. ■...
Page 402 3-5. Using the hands-free phone system (for cellular phone) Making a phone call ■ Making a phone call ● Dialing by inputting a number “Dial by number” ● Dialing by inputting a name “Dial by name” ● Speed dialing ● Dialing a number stored in the outgoing history memory “Redial”...
Page 403 3-5. Using the hands-free phone system (for cellular phone) Dialing by inputting a name Press the talk switch and say “Dial by name”. Select a registered name to be input by either of the following methods: a. Press the talk switch and say a registered name. b.
Page 404 3-5. Using the hands-free phone system (for cellular phone) Transferring a call A call can be transferred between the cellular phone and system while dialing, receiving a call, or during a call. Use one of the follow- ing methods: a. Operate the cellular phone. Refer to the manual that comes with the cellular phone for the oper- ation of the phone.
Page 405 3-5. Using the hands-free phone system (for cellular phone) The following operations can be performed: Dialing: Press the off-hook switch or select “Dial” by using a voice command or Storing the number in the phone book: Select “Store” by using a voice command or Deleting: Select “Delete”...
Page 406 3-5. Using the hands-free phone system (for cellular phone) Setting a cellular phone Registering a cellular phone in the hands-free phone system allows the system to function. The following functions can be used for reg- istered cellular phones: ■ Functions and operation procedures To enter the menu for each function, follow the steps below by using a voice command or ●...
Page 407 3-5. Using the hands-free phone system (for cellular phone) Selecting the cellular phone to be used Select “Select Phone” by using a voice command or Pattern A Select the cellular phone to be used by either of the following methods, and select “Confirm” by using a voice command or a.
Page 408 3-5. Using the hands-free phone system (for cellular phone) Select “Confirm” by using a voice command or Listing the registered cellular phones Selecting “List Phones” by using a voice command or causes the list of registered cellular phones to be read aloud. When listing is complete, the system returns to “Phone Setup”.
Page 409 3-5. Using the hands-free phone system (for cellular phone) Changing the passkey Select “Set Passkey” by using a voice command or Press the talk switch, say a 4 to 8-digit number, and select “Confirm” by using a voice command or The number should be input 1 digit at a time.
Page 410 3-5. Using the hands-free phone system (for cellular phone) Security and system setup To enter the menu of each setting, follow the steps below: ■ Security setting items and operation procedure ● Setting or changing the PIN (Personal Identification Number) 1.
Page 411 3-5. Using the hands-free phone system (for cellular phone) ■ Changing the PIN Select “Set PIN” by using a voice command or Enter the registered PIN by using a voice command or Enter a new PIN by using a voice command or When using , input the code 1 digit at a time.
Page 412 3-5. Using the hands-free phone system (for cellular phone) ® Displaying the Bluetooth device address and name Select “Device Name” using ® Turn to display the Bluetooth device address and name. Select “Go Back” using to return to “System Setup” Initialization Select “Initialize”...
Page 413 3-5. Using the hands-free phone system (for cellular phone) Using the phone book To enter the menu of each setting, follow the steps below: ● Adding a new phone number 1. “Phonebook” → 2. “Add Entry” ● Setting speed dial 1.
Page 414 3-5. Using the hands-free phone system (for cellular phone) ■ Adding procedure Select “Add Entry” by using a voice command or Use one of the following methods to input a telephone num- ber: Inputting a telephone number by using a voice command STEP2-1 Select “By Voice”...
Page 415 3-5. Using the hands-free phone system (for cellular phone) Selecting a phone number from outgoing or incoming call history STEP2-1 Select “Call History” by using a voice command or STEP2-2 Select “Outgoing” or “Incoming” by using a voice command or STEP2-3 Select the data to be registered by either of the fol- lowing methods: a.
Page 416 3-5. Using the hands-free phone system (for cellular phone) Setting speed dials Select “Set Speed Dial (Speed Dial)” by using a voice com- mand or Select the data to be registered as a speed dial by either of the following methods: a.
Page 417 3-5. Using the hands-free phone system (for cellular phone) Changing a registered name Select “Change Name” by using a voice command or Select the name to be changed by either of the following methods. a. Press the talk switch, say desired name, and select “Con- firm”...
Page 418 3-5. Using the hands-free phone system (for cellular phone) Deleting speed dials Select “Delete Speed Dial” by using a voice command or Press the preset button for which the desired speed dial is registered, and select “Confirm” by using a voice command or Listing the registered data Selecting “List names”...
Page 419 3-6. Using the interior lights Interior lights list Your Toyota is equipped with an illuminated entry system to assist in entering the vehicle. Due to the function of the system, the lights shown in the following illustration automatically turn on/off accord- ing to whether the doors are locked/unlocked, whether the doors are opened/closed, and the engine switch position.
Page 420 DOOR position, the lights will turn off automati- cally after 20 minutes. ■ Customization ● That can be configured at Toyota dealer (vehicles without multi-informa- tion display) ● Settings (e.g. The time elapsed before lights turn off) can be changed. (Customizable features →P. 696) ●...
Page 421 3-6. Using the interior lights Personal/interior light main switch and personal/interior lights Personal/interior light main switch The personal/interior lights can- not be individually turned off. DOOR position The personal/interior lights come on when a door is opened. They turn off when the doors are closed.
Page 422 3-6. Using the interior lights Personal/interior lights Front (type B) On/off Front (type C) On/off Rear (type A) On/off...
Page 423 3-6. Using the interior lights Personal/interior lights Rear (type B) On/off Rear (type C) On/off Rear (type D) On/off...
Page 424 3-6. Using the interior lights Cargo lamp main switch Cargo lamp main switch The cargo lamp can not be indi- vidually turned off. DOOR position The cargo lamp comes on when a door is opened. They turn off when the doors are closed. The cargo lamp can be individu- ally turned on or off.
Page 425 3-7. Using the storage features List of storage features Front separated type seats Bottle holders Auxiliary boxes Card holder Overhead console Glove boxes Map holder Front cup holders Console box • Card holder • Map holder • Pen holder • Tissue pocket Rear cup holders (if equipped) Storage box (if equipped)
Page 426 3-7. Using the storage features Front bench type seat Bottle holders Auxiliary boxes Card holder Overhead console Glove boxes Front cup holders Pen holder Auxiliary box • Card holder • Map holder • Tissue pocket Rear cup holders (if equipped) Storage box (if equipped)
Page 427 3-7. Using the storage features Glove boxes CAUTION ■ Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: ●...
Page 428 3-7. Using the storage features Glove boxes Pull the lever up. CAUTION ■ Items that should not be left in the upper glove box Do not leave glasses or lighters in the box. If the interior of the vehicle become hot, lighters may explode and glasses may warp or becomes cracked.
Page 429 3-7. Using the storage features Console box Console box (front separated type seats only) Pull the knob up and lift the lid. ■ Tray in the console box The tray slides forward or backward. The tray can be removed.
Page 430 3-7. Using the storage features Console box The box can be removed. Hanging file folders can be hung on the rails when the box is removed. CAUTION ■ Caution while driving Keep the console box closed. Injuries may result in the event of an accident or sudden braking.
Page 431 3-7. Using the storage features Card holder Card holder Overhead console (type A) Press the lid. Overhead console (type B) Press the lid.
Page 432 3-7. Using the storage features Card holder Console box (front separated type seats) Pull the knob up and lift the lid. Back of the front center seatback (front bench type seat) Pull the lever up and fold down the seatback.
Page 433 3-7. Using the storage features Card holder Push the knob and lift the lid. CAUTION ■ Caution while driving Keep the auxiliary box, console box or holder closed. Injuries may result in the event of an accident or sudden braking.
Page 434 3-7. Using the storage features Map holder Map holder Center console (front separated type seats) Push the tab down to release the lock and remove the lid. Stow the lid.
Page 435 3-7. Using the storage features Map holder Console box (front separated type seats) Pull the lever up and lift the lid. Back of the front center seatback (front bench type seat) Pull the lever up and fold down the seatback.
Page 436 3-7. Using the storage features Map holder Push the knob and lift the lid. CAUTION ■ Caution while driving Keep the auxiliary or console box closed. Injuries may result in the event of an accident or sudden braking.
Page 437 3-7. Using the storage features Pen holder Pen holder Front separated type seats Pull the knob up and lift the lid.
Page 438 3-7. Using the storage features Pen holder Front bench type seat Pull the lever up and fold down the seatback. CAUTION ■ Caution while driving (front separated type seats only) Keep the console box closed. Injuries may result in the event of an accident or sudden braking.
Page 439 3-7. Using the storage features Tissue pocket Tissue pocket Front separated type seats Pull the knob up and lift the lid. Front bench type seat Pull the lever up and fold down the seatback.
Page 440 3-7. Using the storage features Tissue pocket Push the knob and lift the lid. CAUTION ■ Caution while driving Keep the auxiliary or console box closed. Injuries may result in the event of an accident or sudden braking.
Page 441 3-7. Using the storage features Overhead console Overhead console The overhead console is useful for temporarily storing sunglasses and similar small items. Type A Push the knob forward to open the console. Type B Push the knob forward to open the console.
Page 442 3-7. Using the storage features Front cup holders Front cup holders Separated type seats Bench type seat Pull the lever up and fold down the seatback.
Page 443 3-7. Using the storage features Front cup holders ■ Removing the cup holder (separated type seats only) Push the tab down to release the lock and remove the lid. Stow the lid. Pull the cup holder up and remove it. CAUTION ■...
Page 444 3-7. Using the storage features Rear cup holders Rear cup holders Double Cab models with front separated type seats Pull the lid down. Double Cab models with front bench type seat Pull the lid down. CrewMax models Pull the armrest down.
Page 445 3-7. Using the storage features Rear cup holders and bottle holders CAUTION ■ Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.
Page 446 3-7. Using the storage features Bottle holders Rear door (type A) Rear door (type B) ■ Removing the hold separator (front bench type seat only) Remove the hold separator. CAUTION ■ When not in use (front bench type seat only) Keep the bottle holders closed.
Page 447 3-7. Using the storage features Bottle holders and auxiliary boxes NOTICE ■ Items that should not be stowed in the bottle holders Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders, or glasses and paper cups containing liquid. The contents may spill and glasses may break.
Page 448 3-7. Using the storage features Auxiliary boxes Front bench type seat (type B) Pull the lever up and fold down the seatback. Push the knob and lift the lid. Front bench type seat (type C) Pull the lever up and fold down the seatback.
Page 449 3-7. Using the storage features Auxiliary boxes and storage box Push the knob and lift the lid. CAUTION ■ Caution while driving Keep the auxiliary boxes closed. Injuries may result in the event of an accident or sudden braking. Storage box (if equipped) ■...
Page 450 3-7. Using the storage features Storage box Turn the knob in the OPEN direction. Lift the lid. ■ Remove the storage box Pull the lever up and raise the rear seat cushion. Turn the knob in the OPEN direction. Lift the lid. Remove the lids.
Page 451 3-7. Using the storage features Storage box CAUTION ■ Caution while driving Keep the storage box lids closed. Injuries in the event of an accident or sudden braking. ■ To prevent damage to the storage box Do not put heavy loads on the lids.
Page 452 3-8. Other interior features Sun visors ■ Main visor Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. Side extender: Place in side position then slide backwards. ■ Sub visor (if equipped) Flip down.
Page 453 3-8. Other interior features ∗ Vanity mirrors Vehicles without vanity light Open the cover. Vehicles with vanity light Open the cover. The light turns on when the cover is opened. Adjust the brightness of the light. ∗ : If equipped...
Page 454 3-8. Other interior features Clock Adjusts the hours. Adjusts the minutes. ■ For quicker adjustment of the clock (if equipped) Hold down the M or H button continuously. This allows faster advancement of the minutes and hours. ■ The clock is displayed when The engine switch is in the ACC or ON position.
Page 455 3-8. Other interior features ∗ Outside temperature display Displays the outside air temperature. The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C). Switches the outside air temperature display between °C (Celsius) and °F (Fahrenheit). equipped) Vehicles without multi-informa- tion display: Push the SETUP button until...
Page 456 3-8. Other interior features ■ When – –°C or – –°F is displayed The system may be malfunctioning. Take your vehicle to your Toyota dealer. ■ The outside air temperature is displayed when The engine switch is in the ON position.
Page 457 3-8. Other interior features Power outlets (12V DC) The power outlet can be used for accessories that run on less than 10A. Type A (Instrument panel)
Page 458 3-8. Other interior features Type B (Instrument panel) Type C (Back of the front center seatback)
Page 459 3-8. Other interior features Type D (Inside of the console box) Type E (Back of the console box)
Page 460 3-8. Other interior features Type F (Back of the front center seatback) Type G (Back of the console box) ■ The power outlet can be used when The engine switch is in the ACC or ON position.
Page 461 3-8. Other interior features NOTICE ■ To avoid damaging the power outlet Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit. ■...
Page 462 3-8. Other interior features ∗ Power outlets (115V AC) The power outlet can be used for accessories that use less than 100W. Front separated type seats Power outlet socket Front bench type seat Power outlet socket ■ The power outlet can be used when The engine switch is in the ON position.
Page 463 Do not modify, disassemble or repair the power outlet or its inverter, in any way. Doing so may result in unexpected malfunctions or accidents, which could cause serious damage or injuries. Contact a Toyota dealer for any necessary repairs. ■...
Page 464 3-8. Other interior features NOTICE ■ To avoid damaging the power outlet and the plug ● Close the power outlet lid when not in use. ● Foreign objects or liquids that enter the power outlet may cause a short circuit. ●...
Page 465 If the power outlet is loose when an electrical appliance plug is con- nected Replace the outlet. Contact a Toyota dealer for any necessary replacements. ■ If the power outlet gets dirty Turn the main switch off and use a soft, clean cloth to wipe it gently.
Page 466 3-8. Other interior features ∗ Seat heaters The indicator comes on. Adjusts the seat tempera- ture. The further you turn the dial upward, the warmer the seat becomes. ■ The seat heaters can be used when The engine switch is in the ON position. ■...
Page 467 3-8. Other interior features CAUTION ■ Burns ● Use caution when seating the following persons in a seat with the seat heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the disabled •...
Page 468 3-8. Other interior features ∗ Seat heaters and ventilators Blows air from the seats The indicator comes on. The higher the number, the stron- ger the airflow becomes. Heats the seats The indicator comes on. The higher the number, the warmer the seats become.
Page 469 3-8. Other interior features CAUTION ■ Burns ● Use caution when seating the following persons in a seat with the seat heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the disabled •...
Page 470 3-8. Other interior features Armrest (CrewMax models only) Pull the armrest down for use. NOTICE ■ To prevent damage to the armrest ● Do not place too much strain on the armrest. ● Do not sit on the armrest.
Page 471 3-8. Other interior features ∗ Seatback table Front passenger’s seatback can be used as a temporary table only when the vehicle is stopped. Fold down the front passen- ger’s seat to use the seatback table. (→P. 63) CAUTION ■ Caution while driving Observe the following precautions to avoid death or serious injury.
Page 472 3-8. Other interior features Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks (clips) into the floor mat eye- lets.
Page 473 When installing the driver’s floor mat ● Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats. ● Only use floor mats designed for the driver’s seat. ●...
Page 474 3-8. Other interior features Luggage compartment features ■ Deck hooks Deck hooks are provided for securing loose items.
Page 475 3-8. Other interior features ■ Cargo net hooks (CrewMax models only) To hang the cargo net, use the cargo net hooks. The cargo net itself is not included as original equipment. ■ Shopping bag hooks (CrewMax models only) To hang shopping bags, use the shopping bag hooks.
Page 476 3-8. Other interior features NOTICE ■ To prevent damage to the cargo net hooks and shopping bag hooks ● Avoid hanging heavy loads on the cargo net hooks or shopping bag hooks. ● Avoid hanging things other than the cargo net when using the shopping bag hooks as cargo net hooks.
Page 477 3-8. Other interior features ∗ Garage door opener The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, secu- rity systems, and other devices. ® The garage door opener (HomeLink Universal Transceiver) is manufac- ®...
Page 478 3-8. Other interior features ® ■ Programming the HomeLink Point the remote control trans- mitter for the device 1 to 3 in. (25 ® to 75 mm) from the HomeLink control buttons. Keep indicator ® HomeLink in view while pro- gramming.
Page 479 3-8. Other interior features Test operation ® HomeLink pressing newly programmed button. If programming a garage door opener, check to see if the garage door opens and closes. If the garage door does not operate, see if your garage transmitter is of the Rolling Code type.
Page 480 Repeat the steps above to program another device for each of ® the remaining HomeLink buttons. ■ Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance.
Page 481 3-8. Other interior features ■ Reprogramming a button ® The individual HomeLink buttons cannot be erased but can be reprogrammed. To reprogram a button, follow the programming instructions. ® Operating the HomeLink ® ® Press the appropriate HomeLink button. The HomeLink indicator ®...
Page 482 3-8. Other interior features ■ Before programming ● Install a new battery in the remote control transmitter. ● The battery side of the remote control transmitter must be pointed away ® from the HomeLink ■ Certification for the garage door opener For vehicles sold in the U.S.A.
Page 483 3-8. Other interior features CAUTION ■ When programming a garage door or other remote control device The garage door may operate, so ensure that people and objects are out of danger to prevent potential harm. ■ Conforming to federal safety standards ®...
Page 484 3-8. Other interior features ∗ Compass The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation Type A To turn the compass on or off, press the switch. Type B ∗ : If equipped...
Page 485 3-8. Other interior features ■ Displays and directions Display Direction North Northeast East Southeast South Southwest West Northwest Calibrating the compass Samoa: 5 Guam: 8 Saipan: 8 The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle.
Page 486 3-8. Other interior features ■ Deviation calibration Stop the vehicle where it is safe to drive in a circle. Press the switch until a number (1 to 15) appears on the com- pass display. Type A Type B Press the switch, and referring to the map above, select the number of the zone where you are.
Page 487 3-8. Other interior features ■ Circling calibration When “C” appears on the dis- play, drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed. If there is not enough space to drive in a circle, drive around the block until the direction is dis- played.
Page 488 3-8. Other interior features NOTICE ■ To avoid the compass malfunctions Do not place magnets or any metal objects near the inside rear view mirror. Doing this may cause a malfunction of the compass sensor. ■ To ensure normal operation of the compass ●...
Page 489 4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition. ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 490 4-1. Maintenance and care ■ Aluminum wheels (if equipped) ● Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint. ●...
Page 491 4-1. Maintenance and care NOTICE ■ Cleaning the exterior lights ● Wash carefully. Do not use organic substances or scrub with a hard brush. This may damage the surfaces of the lights. ● Do not apply wax on the surfaces of the lights. Wax may cause damage to the lenses.
Page 492 4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle’s interior and keep it in top condition: ■ Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.
Page 493 4-1. Maintenance and care ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam.
Page 494 4-1. Maintenance and care NOTICE ■ Cleaning detergents ● Do not use organic substances such as benzene or gasoline, acidic or alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces. ●...
Page 495 ■ Repair and replacement It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than Toyota dealer performs repairs, confirm the war- ranty coverage.
Page 496 Continue to press and hold the button until “MAINT REQD RESET MODE COMPLETE” appears on the multi-information display. ■ Allow inspection and repairs to be performed by a Toyota dealer ● Toyota technicians are well-trained specialists and are kept up to date with the latest service information.
Page 497 “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items...
Page 498 4-2. Maintenance Vehicle interior Items Check points • Moves smoothly (without uneven Accelerator pedal pedal effort or catching)? • Can the vehicle be held securely Automatic transmission “Park” on an incline with the shift lever in mechanism • Moves smoothly? •...
Page 499 4-2. Maintenance Vehicle exterior Items Check points Doors • Operate smoothly? Engine hood • The lock system works properly? • Is there any leakage after park- Fluid leaks ing? • Inflation pressure is correct? • Tire surfaces not worn or dam- aged? Tire •...
Page 500 If the malfunction indicator lamp comes on The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. ■...
Page 501 • FMVSS No.116 DOT 3 or SAE Brake fluid level (→P. 550) J1703 brake fluid • Rag or paper towel • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
Page 502 4-3. Do-it-yourself maintenance Items Parts and tools • Bulb with same number and watt- age rating as original Light bulbs (→P. 588) • Phillips-head screwdriver • Flathead screwdriver • Automatic transmission fluid Power steering fluid level ® DEXRON II or III (→P.
Page 503 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury observe the following precautions. ■ When working on the engine compartment ● Keep hands, clothing, and tools away from the moving fan and engine drive belt.
Page 504 4-3. Do-it-yourself maintenance NOTICE ■ If you remove the air cleaner Driving with the air cleaner removed may cause excessive engine wear due to dirt in the air. Also a backfire could cause a fire in the engine compart- ment. ■...
Page 505 4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood lock release lever. The hood will pop up slightly. Pull up the hood catch lever and lift the hood. CAUTION ■...
Page 506 4-3. Do-it-yourself maintenance Engine compartment 4.0L V6 (1GR-FE) engine Washer fluid tank (→P. 555) Brake fluid reservoir (→P. 550) Engine oil level dipstick (→P. 545) Fuse box (→P. 577) Engine coolant reservoir Battery (→P. 553) (→P. 549) Radiator (→P. 550) Engine oil filler cap Condenser (→P.
Page 507 4-3. Do-it-yourself maintenance 4.6L V8 (1UR-FE) and 5.7L V8 (3UR-FE, 3UR-FBE) engines Washer fluid tank (→P. 555) Brake fluid reservoir (→P. 550) Engine oil level dipstick (→P. 545) Fuse box (→P. 577) Engine coolant reservoir Battery (→P. 553) (→P. 549) Radiator (→P.
Page 508 4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine.
Page 509 4-3. Do-it-yourself maintenance Wipe the dipstick and reinsert it fully. Full ■ Adding engine oil 4.0L V6 (1GR-FE) engine If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine.
Page 510 4-3. Do-it-yourself maintenance Remove the oil filler cap, turning it counterclockwise. Add engine oil slowly. Checking the dipstick. Reinstall the filler cap, turning it clockwise. The approximate quantity of oil needed to raise the level between low and full on the dipstick is indicated as follows: 1.6 qt.
Page 511 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
Page 512 If the coolant level drops within a short time after replenishing Visually check the radiator, hoses, reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer pressure test the cap and check for leaks in the cooling system. ■...
Page 513 Radiator and condenser Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer. CAUTION ■...
Page 514 4-3. Do-it-yourself maintenance ■ Adding fluid Make sure to check the fluid type and prepare the necessary items. Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Items Rag or paper towel ■ Brake fluid can absorb moisture from the air Excess moisture in the fluid can cause a dangerous loss of braking effi- ciency.
Page 515 4-3. Do-it-yourself maintenance Power steering fluid ■ Fluid level The fluid level should be within the appropriate range. Full (when cold) Add fluid (when cold) Full (when hot) Add fluid (when hot) Hot: Vehicle has been driven around 50 mph (80 km/h) for 20 minutes, or slightly longer in frigid temperatures.
Page 516 4-3. Do-it-yourself maintenance NOTICE ■ When adding fluid Avoid overfilling, or the power steering may be damaged. ■ After replacing the reservoir cap Check the steering box case, vane pump and hose connections for leaks or damage. Battery ■ Battery exterior Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.
Page 517 4-3. Do-it-yourself maintenance CAUTION ■ Chemicals in the battery A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near bat- tery: ●...
Page 518 4-3. Do-it-yourself maintenance NOTICE ■ When recharging the battery Never recharge the battery while the engine is running. Also, be sure all accessories are turned off. Washer fluid Add washer fluid in the following situations. ● Any washer does not work. ●...
Page 519 4-3. Do-it-yourself maintenance CAUTION ■ When refilling the washer fluid Do not refill the washer fluid when the engine is hot or running, as the washer fluid contains alcohol and may catch fire if spilled on the engine etc. NOTICE ■...
Page 520 ■ The tire pressure warning system Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (→P. 611)
Page 521 ID codes must be regis- tered in the tire pressure warning computer and tire pressure warning system must be initialized. Have tire pressure warning valve and trans- mitter ID codes registered by your Toyota dealer. (→P. 559) Initializing the tire pressure warning system ■...
Page 522 ● A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer.
Page 523 4-3. Do-it-yourself maintenance ■ Replacing tires and wheels If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light comes on after blinking for 1 minute to indicate a system malfunction.
Page 524 Initialization can be completed in several minutes. However, in the fol- lowing cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. ●...
Page 525 4-3. Do-it-yourself maintenance ■ Routine tire inflation pressure checks The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks. ■ Tire pressure warning system certification FCC ID: GQ4-45T FCC ID: GQ4-32T FCC ID: GQ4-37R...
Page 526 Do not mix tires of different makes, models or tread patterns. Also, do not mix tires of remarkably different treadwear. ● Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply tires).
Page 527 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 528 4-3. Do-it-yourself maintenance Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (→P. 685)
Page 529 4-3. Do-it-yourself maintenance ■ Inspection and adjustment procedure Tire valve Tire pressure gauge Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pressure is not within the recommended levels, adjust inflate the tire.
Page 530 Reduced driving comfort and tire life ● Reduced safety ● Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer. ■ Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: ●...
Page 531 4-3. Do-it-yourself maintenance CAUTION ■ Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. ● Excessive wear ● Uneven wear ●...
Page 532 ● Bent wheels that have been straightened ■ Wheel precautions ● Use only Toyota wheel nuts and wrench designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 100 miles (160 km).
Page 533 ■ When replacing wheels The wheels of your Toyota are equipped with tire pressure warning valves and transmitters (except for spare tire) that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure.
Page 534 Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
Page 535 4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be cleaned or changed regularly to maintain air conditioning efficiency. ■ Removal method Turn the engine switch off. Open the glove box. Remove the tray. Remove the cover by sliding up while pulling toward you.
Page 536 Hold the air gun 2 in. (5 cm) from the filter and blow for approximately 2 minutes at 72 psi (500 kPa, 5.0 kgf/cm or bar). If it is not available, have the filter cleaned by your Toyota dealer.
Page 537 4-3. Do-it-yourself maintenance ■ Replacement method Remove the air conditioning filter and replace it with a new one. The “↑UP” marks shown on the filter should be pointing up. ■ Checking interval Inspect, clean and replace the air conditioning filter according to the mainte- nance schedule.
Page 538 4-3. Do-it-yourself maintenance Wireless remote control battery Replace the battery with a new one if it is discharged. ■ You will need the following items: Lithium battery CR2032 ■ Replacing the battery Remove the cover using a coin protected with tape etc. Remove the discharged trans- mitter battery.
Page 539 ● The operational range is reduced. ■ Use a CR2032 lithium battery ● Batteries can be purchased at your Toyota dealer, jewelers, or camera stores. ● Replace only with the same or equivalent type recommended by your Toyota dealer. ●...
Page 540 4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Turn the engine switch off. The fuses are located in the following places. To check the fuses, follow the instructions below.
Page 541 4-3. Do-it-yourself maintenance Remove the fuse with the pull- out tool.
Page 542 Type B Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid. Type C Normal fuse Blown fuse Contact your Toyota dealer.
Page 543 4-3. Do-it-yourself maintenance Fuse layout and amperage ratings ■ Engine compartment Fuse Ampere Circuit Multiport fuel injection system/ 15 A sequential multiport fuel injection system HORN 10 A Horn Multiport fuel injection system/ EFI NO.1 25 A sequential multiport fuel injection system IG2 MAIN 30 A...
Page 544 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Stop lights, high mounted stop- light, vehicle stability control sys- tem, anti-lock brake system, shift STOP 15 A lock system, multiport fuel injection system/sequential multiport fuel injection system, towing converter TOW BRK 30 A Trailer brake controller Multiport fuel injection system/ 7.5 A...
Page 545 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Multiplex communication system, Multiport fuel injection system/ sequential multiport fuel injection ECU-B1 7.5 A system, auto anti-glare inside rear view mirror, power outlets, power front driver’s seat, power tilt and power telescopic Interior lights, personal lights, van- DOME 7.5 A ity lights, engine switch light, foot...
Page 546 4-3. Do-it-yourself maintenance Fuse Ampere Circuit DEFOG 40 A Back window defogger SUB BATT 40 A Trailer towing Anti-lock brake system, vehicle sta- ABS1 50 A bility control system Anti-lock brake system, vehicle sta- ABS2 40 A bility control system 30 A Starting system 50 A...
Page 547 4-3. Do-it-yourself maintenance ■ Under the instrument panel Fuse Ampere Circuit INVERTER 15 A Power outlet (115V) FR P/SEAT LH 30 A Power front driver’s seat DR/LCK 25 A Multiplex communication system 7.5 A On-board diagnosis system PWR OUTLET 15 A Power outlets CARGO LP 7.5 A...
Page 548 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Anti-lock brake system, vehicle sta- bility control system, multiplex com- munication system, intuitive parking assist system, power front ECU-IG No.1 7.5 A driver’s seat, power tilt and power telescopic, shift lock, tire pressure warning system, accessory meter, trailer towing, power outlet, electric moon roof Back-up lights, charging system,...
Page 549 Never use a fuse of a higher amperage rating than indicated, or use any other object in place of a fuse. ● Always use a genuine Toyota fuse or equivalent. Never replace a fuse with a wire, even as a temporary fix. This can cause extensive damage or even fire.
Page 550 4-3. Do-it-yourself maintenance NOTICE ■ Before replacing fuses Have the cause of electrical overload determined and repaired by your Toy- ota dealer as soon as possible.
Page 551 You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 552 4-3. Do-it-yourself maintenance ■ Rear bulb locations High mounted stoplight Stop/tail and rear and cargo lamps side marker lights Rear turn signal lights License plate lights Back-up lights Replacing light bulbs ■ Headlight high beam Unplug connector while depressing the lock release.
Page 553 4-3. Do-it-yourself maintenance Turn the bulb base counterclock- wise. ■ Headlight low beam Unplug connector while depressing the lock release. Turn the bulb base counterclock- wise.
Page 554 4-3. Do-it-yourself maintenance ■ Front turn signal/parking lights/daytime running lights (if equipped) Turn the bulb base counterclock- wise. Remove the light bulb.
Page 555 4-3. Do-it-yourself maintenance ■ Front side marker lights Remove the fender liner clip. Partly remove the fender liner and turn the bulb base counter- clockwise.
Page 556 4-3. Do-it-yourself maintenance Remove the light bulb. ■ Front fog lights (if equipped) Remove the bolts and partly remove the fender liner. Turn the bulb counterclockwise.
Page 557 4-3. Do-it-yourself maintenance Unplug connector while depressing the lock release. ■ Stop/tail and rear side marker lights, rear turn signal lights and back-up lights Remove the bolts and rear com- bination assembly. Turn the bulb bases counter- clockwise. Stop/tail and rear side marker light Rear turn signal light Back-up light...
Page 558 4-3. Do-it-yourself maintenance Remove the light bulb. Stop/tail and rear side marker light Rear turn signal light Back-up light ■ High mounted stoplight and cargo lamps Remove the screws and cover. Remove the light bulb. High mounted stoplight Cargo lamps...
Page 559 4-3. Do-it-yourself maintenance ■ License plate lights Remove the screw and light unit. Turn the bulb base counterclock- wise. Remove the light bulb.
Page 560 LED side turn signal lights The side turn signal light consists of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. ■ Installing the fender liner clips...
Page 561 4-3. Do-it-yourself maintenance CAUTION ■ Replacing light bulbs ● Turn off the headlights. Do not attempt to replace the bulb immediately after turning off the headlights. The bulbs become very hot and may cause burns. ● Do not touch the glass portion of the light bulb with bare hands. Hold the bulb by the plastic or metal portion.
Page 562 5-1. Essential information Emergency flashers Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash all the turn signal lights. To turn them off, press the switch once again. NOTICE ■ To prevent battery discharge Do not leave the emergency flashers on longer than necessary when the engine is not running.
Page 563 If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws.
Page 564 5-1. Essential information Type B Towing eyelet ■ Emergency towing procedure The engine switch must be in the ACC (engine off) or the ON (engine running) position. 4WD models: Put the front-wheel drive control switch in 2WD. Shift the shift lever to N. Release the parking brake.
Page 565 5-1. Essential information NOTICE ■ To prevent serious damage to the transmission Never tow this vehicle from the rear with the four wheels on the ground. This may cause serious damage to the transmission. ■ Emergency towing eyelet precautions ● Before emergency towing, check that the eyelet is not broken or damaged and that the installation bolts are not loose.
Page 566 5-1. Essential information Towing with a wheel lift-type truck from the front Use a towing dolly under the rear wheels. NOTICE ■ To prevent serious damage to the transmission Never tow this vehicle wheels on the ground. Towing with a wheel lift-type truck from the rear 2WD models Turn the engine switch to the ACC position.
Page 567 Without adequate clearance, the vehicle could be damaged while being towed. Using a flat bed truck If your Toyota is transported by a Front flat bed truck, it should be tied down at the locations shown in...
Page 568 5-1. Essential information If you use chains or cables to tie down your vehicle, the angles indicated by triangles must be 45°. Do not overly tighten the tie downs or the vehicle may be damaged. Apply the parking brake firmly.
Page 569 5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms ● Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.)
Page 570 5-1. Essential information Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine. Follow the procedure below to restart the engine after the system is activated.
Page 571 Stop the vehicle immediately. The following warnings indicate the possibility of damage to the vehi- cle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning light Warning light/Details Charging system warning light Indicates a malfunction in the vehicle’s charging sys-...
Page 572 Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning light Warning light/Details Malfunction indicator lamp Indicates a malfunction in: •...
Page 573 5-2. Steps to take in an emergency Warning light Warning light/Details Slip indicator The indicator comes on to indicate a malfunction in: • The VSC; • The TRAC; • The A-TRAC or • The AUTO LSD system. Automatic transmission fluid temperature warn- ing light •...
Page 574 In case the light does not turn off even if the tire infla- tion pressure is adjusted, have the system checked by your Toyota dealer. When the light comes on Have the system after blinking for 1 checked by your Toy- minute: ota dealer.
Page 575 5-2. Steps to take in an emergency Warning light Warning light/Details Correction procedure Maintenance required reminder light Indicates that mainte- nance is required accord- ing to the driven distance on the maintenance schedule. Illuminates for about 3 seconds and then flashes for about 15 seconds If necessary, perform approximately 4500 miles...
Page 576 Is the fuel tank cap loose? If it is, tighten it securely. The light will go off after taking several driving trips. If the light does not go off even after several trips, contact your Toyota dealer as soon as possible.
Page 577 5-2. Steps to take in an emergency ■ Front passenger detection sensor and passenger seat belt reminder If luggage or other load is placed on the right front passenger seat, depend- ing on its weight, the reminder light to flash and buzzer to sound. ■...
Page 578 If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings. ● If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.) ●...
Page 579 5-2. Steps to take in an emergency CAUTION ■ Maintenance of the tire Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label).
Page 580 5-2. Steps to take in an emergency CAUTION TPMS (tire pressure warning system) malfunctions may occur for a vari- ety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS (tire pressure warning system) from functioning properly.
Page 581 Stop the vehicle immediately. The following warnings indicate the possibility of damage to the vehi- cle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning message Details Indicates that the engine coolant temperature is too high A buzzer also sounds.
Page 582 5-2. Steps to take in an emergency Warning message Details Indicates a malfunction in the automatic transmis- sion system A buzzer also sounds. Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning light turns off. Warning message Details Correction procedure...
Page 583 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that the washer fluid level is low. Add washer fluid. A buzzer also sounds. Indicates that all mainte- nance according to the driven distance on the maintenance schedule* should be performed If necessary, perform soon.
Page 584 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that the fuel level is low. Fill up the tank as soon A buzzer also sounds as possible. and the low fuel level warning light comes on. : Refer to the separate “Scheduled Maintenance Guide”...
Page 585 5-2. Steps to take in an emergency If you have a flat tire Remove the flat tire and replace it with the spare provided. ■ Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ●...
Page 586 5-2. Steps to take in an emergency Double Cab models without storage box Tool bag Jack Double Cab models with storage box Tool bag Jack CrewMax models Tool bag Jack...
Page 587 5-2. Steps to take in an emergency Taking out the jack and tool bag (Regular Cab models) Pull the lever and fold down the seatback. Remove the cover. Unhook the strap and remove the tool bag.
Page 588 5-2. Steps to take in an emergency Unhook the strap. Loosen and remove the jack. Loosen Tighten Taking out the jack and tool bag (Double Cab models) Pull up the lever. Raise the bottom cushion up.
Page 589 5-2. Steps to take in an emergency Vehicles with storage box Turn the knob to the OPEN direction. Remove the lid. Vehicles with storage box Remove the jack cover panel. Unhook the strap. Loosen and remove the jack. Loosen Tighten Unhook the strap and remove the tool bag.
Page 590 5-2. Steps to take in an emergency Taking out the jack and tool bag (CrewMax models) Pull the lever and fold down the seatback. Remove the cover. Unhook the strap and remove the tool bag. Unhook the strap.
Page 591 5-2. Steps to take in an emergency Loosen and remove the jack. Loosen Tighten Assemble the jack handle (in the tool bag) Assemble the jack handle exten- sion as shown.
Page 592 5-2. Steps to take in an emergency Taking out the spare tire Insert the end of the jack handle extension into lowering screw and turn it counterclock- wise. After the tire is lowered com- pletely to the ground, remove the holding bracket.
Page 593 5-2. Steps to take in an emergency Replacing a flat tire Chock the tires. Wheel Flat tire chock positions Behind the Left- rear right- hand hand side side tire Front Behind the Right- rear left- hand hand side side tire In front of Left- the front...
Page 594 5-2. Steps to take in an emergency Assemble the jack handle exten- sion as shown. Position the jack at the correct jack point as shown. Front Front Rear Make sure the jack is positioned on a level and solid place. Raise the vehicle until the tire is slightly raised off the ground.
Page 595 5-2. Steps to take in an emergency Installing the tire Remove any dirt or foreign mat- ter from the wheel contact sur- face. If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle.
Page 596 5-2. Steps to take in an emergency Lower the vehicle. Firmly tighten each nut two or three times in the order shown in the illustration. Tightening torque Flat washer type (Aluminum wheels) 97 ft·lbf (131 N·m, 13.4 kgf·m) Taper type (Steel wheels) 154 ft·lbf (209 N·m, 21.3 kgf·m) : When temporarily used on...
Page 597 5-2. Steps to take in an emergency Stowing the flat tire, jack and all tools Remove the center wheel ornament by pushing from the reverse side. Lay down the tire with the outer side facing up, and install the holding bracket. Fasten the claws of the holding bracket into the wheel holes as shown in the illustration.
Page 598 5-2. Steps to take in an emergency CAUTION ■ Using the jack Improper use of the jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack. ● Do not use the jack for any purpose other than replacing tires or install- ing and removing tire chains.
Page 599 • If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer. • When installing the wheel nuts, be sure to install them with the tapered ends facing inward.
Page 600 5-2. Steps to take in an emergency CAUTION ■ When using the temporary spare tire ● Remember that your temporary spare tire is specifically designed for use with your vehicle. Do not use your temporary spare tire on another vehicle. ●...
Page 601 5-2. Steps to take in an emergency CAUTION ■ When the spare tire is attached The vehicle speed may not be correctly detected, and the following sys- tems may not operate correctly: ● ABS & Brake assist ● ● TRAC ●...
Page 602 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and...
Page 603 5-2. Steps to take in an emergency If the engine will not start If the engine still does not start after following the correct starting procedure (→P. 178) or releasing the steering lock (→P. 179), confirm the following points. ■ The engine will not start even when the starter motor oper- ates normally.
Page 604 One of the following may be the cause of the problem. ● One or both of the battery terminals may be disconnected. ● The battery may be discharged. (→P. 647) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown.
Page 605 (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
Page 606 5-2. Steps to take in an emergency Column-shift type Press the shift lock override button. The shift lever can be shifted while the button is pressed. Floor shift type...
Page 607 5-2. Steps to take in an emergency Column-shift type...
Page 608 5-2. Steps to take in an emergency If you lose your keys New genuine Toyota keys can be made by your Toyota dealer using the key number stamped on your key number plate. Vehicles with engine immobilizer system, the dealer will also need the master key.
Page 609 You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your Toyota following the steps below. Connect the jumper cables.
Page 610 Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were con- nected. Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible.
Page 611 5-2. Steps to take in an emergency ■ Starting the engine when the battery is discharged The engine cannot be started by push-starting. ■ Avoiding a discharged battery ● Turn off the headlights and the audio system while the engine is turned off.
Page 612 5-2. Steps to take in an emergency CAUTION ■ Avoiding battery fires or explosions Observe the following precautions to prevent accidentally igniting the flam- mable gas that may be emitted from the battery. ● Make sure the jumper cable is connected to the correct terminal and that it is not unintentionally in contact with any part other than the intended termi- nal.
Page 613 If the fan is operating: Wait until the temperature of the engine (shown on the instrument cluster) begins to fall and then stop the engine. If the fan is not operating: Stop the engine immediately and call your local Toyota dealer.
Page 614 Note that water draining from the air conditioning is normal if it has been used. Add engine coolant if required. Water can be used in an emer- gency if engine coolant is unavailable. (→P. 673) Have the vehicle checked at your nearest Toyota dealer as soon as possible.
Page 615 5-2. Steps to take in an emergency ■ Overheating If you observe the following, your vehicle may be overheating. ● The engine coolant temperature gauge enters the red zone or a loss of power is experienced. ● Steam is coming from under the hood. ●...
Page 616 5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. Stop the engine. Set the parking brake and put the shift lever in P.
Page 617 5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure: Steadily step on the brake pedal with both feet and firmly depress it.
Page 618 5-2. Steps to take in an emergency CAUTION ■ If the engine has to be turned off while driving ● Power assist for the brakes and steering wheel will be lost, making the brake pedal harder to depress and the steering wheel heavier to turn. Decelerate as much as possible before turning off the engine.
Page 619 6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions 2WD models Cab type Regular Cab Double Cab Bed type Standard Long Standard Long Overall 210.2 in. 248.0 in. 229.1 in. (5820 mm) length (5340 mm) (6300 mm) Overall width 79.9 in. (2030 mm) 75.9 in.
Page 620 6-1. Specifications Cab type CrewMax Bed type Short Overall 229.1 in. (5820 mm) length Overall width 79.9 in. (2030 mm) 75.7 in. (1925 mm) Overall height 75.5 in. (1920 mm) Wheelbase 145.6 in. (3700 mm) Front tread 67.9 in. (1725 mm) Rear tread 67.9 in.
Page 621 6-1. Specifications 4WD models Cab type Regular Cab Double Cab Bed type Standard Long Standard Long Overall 210.2 in. 248.0 in. 229.1 in. (5820 mm) length (5340 mm) (6300 mm) Overall width 79.9 in. (2030 mm) 76.3 in. 76.1 in. 76.3 in.
Page 622 6-1. Specifications Cab type CrewMax Bed type Short Overall length 229.1 in. (5820 mm) Overall width 79.9 in. (2030 mm) 76.1 in. (1935 mm) Overall height 75.9 in. (1930 mm) Wheelbase 145.6 in. (3700 mm) Front tread 67.9 in. (1725 mm) Rear tread 67.9 in.
Page 623 6-1. Specifications Vehicle capacity weight Regular Cab models Driving Vehicle capacity weight Model code Engine Bed type system (Occupants+luggage) 4.0L V6 GSK50L-TRADKA Standard 1485 lb. (670 kg) (1GR-FE) GSK51L-THADKA Long 1580 lb. (715 kg) engine 4.6L V8 1710 lb. (775 kg) UPK50L-TRTDKA (1UR-FE) Standard...
Page 624 6-1. Specifications Double Cab models Driving Vehicle capacity weight Model code Engine Bed type system (Occupants+luggage) 4.0L V6 GSK51L-CRASKA (1GR-FE) Standard 1325 lb. (600 kg) engine 1410 lb. (635 kg) UPK51L-CRTSKA 4.6L V8 1335 lb. (605 kg) (1UR-FE) Standard 1330 lb. (600 kg) engine UPK56L-CRTSKA 1255 lb.
Page 625 6-1. Specifications CrewMax models Driving Vehicle capacity weight Model code Engine Bed type system (Occupants+luggage) 1365 lb. (615 kg) UPK51L-PSTSKA 1330 lb. (600 kg) 4.6L V8 1260 lb. (570 kg) (1UR-FE) 1285 lb. (580 kg) engine UPK56L-PSTSKA 1250 lb. (565 kg) 1175 lb.
Page 626 6-1. Specifications TWR (Trailer Weight Rating) Regular Cab models Driving Model code Engine Bed type system (Trailer weight + cargo) 4.0L V6 GSK50L-TRADKA Standard 4900 lb. (2220 kg) (1GR-FE) GSK51L-THADKA Long 4800 lb. (2175 kg) engine 4.6L V8 7100 lb. (3220 kg) UPK50L-TRTDKA (1UR-FE) Standard...
Page 627 6-1. Specifications Double Cab models Driving Model code Engine Bed type system (Trailer weight + cargo) 4.0L V6 GSK51L-CRASKA (1GR-FE) Standard 4500 lb. (2040 kg) engine 6700 lb. (3035 kg) UPK51L-CRTSKA 4.6L V8 8200 lb. (3715 kg) (1UR-FE) Standard 6400 lb. (2900 kg) engine UPK56L-CRTSKA 7900 lb.
Page 628 6-1. Specifications CrewMax models Driving Model code Engine Bed type system (Trailer weight + cargo) 6600 lb. (2990 kg) UPK51L-PSTSKA 4.6L V8 8100 lb. (3670 kg) (1UR-FE) 6200 lb. (2810 kg) engine UPK56L-PSTSKA 7700 lb. (3490 kg) 8000 lb. (3625 kg) USK51L-PSTSKA 9900 lb.
Page 629 Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 630 6-1. Specifications ■ Engine number The engine number is stamped on the engine block as shown. 4.0L V6 (1GR-FE) engine 4.6L V8 (1UR-FE) engine 5.7L V8 (3UR-FE, 3UR-FBE) engine...
Page 631 6-1. Specifications Engine 4.0L V6 (1GR-FE) engine Model 1GR-FE Type 6-cylinder V-type, 4-cycle, gasoline 3.70 × 3.74 in. (94.0 × 95.0 mm) Bore and stroke Displacement 241.4 cu.in. (3956 cm Drive belt tension Automatic adjustment Valve clearance Automatic adjustment (engine cold) 4.6L V8 (1UR-FE) and 5.7L V8 (3UR-FE, 3UR-FBE) engines Model 1UR-FE, 3UR-FE, 3UR- FBE...
Page 632 6-1. Specifications Fuel Engine Gasoline engine Flex-fuel engine Unleaded gasoline, E85, Fuel type Unleaded gasoline only or a blend of the two fuels Octane rating 87 (Research octane number 91) or higher (Unleaded gasoline) Ethanol percentage ⎯ 85% or less (E85) Fuel tank capacity 26.4 gal.
Page 633 6-1. Specifications ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade: ILSAC multigrade engine oil Recommended viscosity: SAE 0W-20...
Page 634 3UR-FBE) Vehicles with towing package engine 13.7 qt. (13.0 L, 11.4 Imp. qt.) Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based Coolant type non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
Page 635 6-1. Specifications Ignition system Spark plug Make DENSO SK20HR11 0.043 in. (1.1 mm) NOTICE ■ Iridium-tipped spark plugs Use only iridium-tipped spark plugs. Do not adjust gap when tuning engine. Electrical system Battery 12.6 ⎯ 12.8 V Fully charged Open voltage at 12.2 ⎯...
Page 636 Oil LT 75W-85 GL-5 or equiva- lent : Your Toyota vehicle is filled with “Toyota Genuine Differential Gear Oil” at the factory. Use Toyota approved “Toyota Genuine Differential Gear Oil” or an equivalent of matching quality to satisfy the above specification. Please con-...
Page 637 NOTICE ■ Automatic transmission fluid type Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the automatic transmis- sion of your vehicle.
Page 638 6-1. Specifications Brakes Pedal clearance 4.1 in. (104 mm) Min. 0.04 ⎯ 0.24 in. (1 ⎯ 6 mm) Pedal free play Brake pad wear limit 0.04 in. (1.0 mm) Parking brake lining wear limit 0.04 in. (1.0 mm) Parking brake pedal travel 6 —...
Page 639 6-1. Specifications Tires and wheels Type A Tire size P255/70R18 112T Front tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Tire inflation pressure Rear tires: (Recommended cold tire 33 psi (230 kPa, 2.3 kgf/cm or bar) inflation pressure) Spare tire: 33 psi (230 kPa, 2.3 kgf/cm or bar) 18 ×...
Page 640 6-1. Specifications Type C P275/55R20 111H, Tire size P255/70R18 112T (spare tire) Front tires: 30 psi (210 kPa, 2.1 kgf/cm or bar) Tire inflation pressure Rear tires: (Recommended cold tire 33 psi (230 kPa, 2.3 kgf/cm or bar) inflation pressure) Spare tire: 33 psi (230 kPa, 2.3 kgf/cm or bar)
Page 641 6-1. Specifications Light bulbs Light Bulbs Bulb No. Type Headlights 9005 (high beam) Headlights (low beam) Front fog lights 9145 Front side marker lights Front turn signal/parking 4157NAK 28/8 lights/daytime running lights Exterior Rear turn signal lights 3157A 27/8 Stop/tail and rear side 3157 27/8 marker lights...
Page 642 At minimum, the E85 you use should meet the specifications of ASTM D5798 in the U.S.A. ■ Fuel tank opening for unleaded gasoline To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.
Page 643 In very few cases, driveability problems may be caused by the brand of fuel you are using. If driveability problems persist, try changing the brand of fuel. If this does not correct the problem, consult your Toyota dealer. ■ Gasoline quality standards ●...
Page 644 Toyota allows the use of oxygenate blended gasoline where the oxygen- ate content is up to 10% ethanol or 15% MTBE. ● If you use gasohol in your Toyota, be sure that it has an octane rating no lower than 87. ●...
Page 645 6-1. Specifications NOTICE ■ Notice on fuel quality ● Do not use improper fuels. If improper fuels are used the engine will be damaged. ● Do not use leaded gasoline. Leaded gasoline can cause damage to your vehicle’s three-way catalytic converters causing the emission control system to malfunction.
Page 646 6-1. Specifications Tire information Typical tire symbols Tire size (→P. 687) DOT and Tire Identification Number (TIN) (→P. 686) Location of treadwear indicators (→P. 557) Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire.
Page 647 6-1. Specifications Radial tires or bias-ply tires A radial tire has RADIAL on the sidewall. A tire not marked RADIAL is a bias-ply tire. Summer tire or all season tire (→P. 560) An all season tire has M+S on the sidewall. A tire not marked M+S is a summer tire.
Page 648 6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits) Speed symbol...
Page 649 U.S.A. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. ■ DOT quality grades All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades.
Page 650 6-1. Specifications ■ Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100.
Page 651 6-1. Specifications Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either sepa- rately or in combination, can cause heat buildup and possible tire fail- ure.
Page 652 6-1. Specifications Tire related term Meaning Distribution of occupants in a vehicle as speci- Occupant distribution fied in the third column of Table 1 below The combined weight of installed regular pro- duction options weighing over 5 lb. (2.3 kg) in excess of the standard items which they Production options replace, not previously considered in curb...
Page 653 6-1. Specifications Tire related term Meaning The part of the tire that is made of steel wires, Bead wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components Bead separation in the bead A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles...
Page 654 6-1. Specifications Tire related term Meaning (a)The sidewall that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on Intended outboard the other sidewall of the tire, or sidewall (b)The outward facing sidewall of asymmetrical tire that has a particular side that must...
Page 655 6-1. Specifications Tire related term Meaning A parting of rubber compound between adja- Ply separation cent plies A mechanical device made of rubber, chemi- cals, fabric and steel or other materials, that, Pneumatic tire when mounted on an automotive wheel, pro- vides the traction and contains the gas or fluid that sustains the load A pneumatic tire in which the ply cords that...
Page 656 6-1. Specifications Tire related term Meaning That portion of a tire that comes into contact Tread with the road A tread section running circumferentially Tread rib around a tire Tread separation Pulling away of the tread from the tire carcass The projections within the principal grooves Treadwear indicators designed to give a visual indication of the...
Page 657 Programming these preferences requires specialized equipment and may be performed by an autho- rized Toyota dealership. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details. Customized Item Function...
Page 658 6-2. Customization Customized Item Function Default setting setting Speed-detecting auto- matic door lock function Opening driver’s door unlocks all doors. Shifting levers to “P” unlocks all doors. Door lock Shifting levers to posi- (→P. 49) tion other than “P” locks all doors.
Page 659 6-2. Customization Customized Item Function Default setting setting 7.5 seconds Time elapsed before 15 seconds lights turn off 30 seconds Illumination Operation after the → P. 455) engine is off Operation when the doors are unlocked Seat Belt Vehicle speed linked Reminder seat belt reminder Buzzer...
Page 660 6-2. Customization Items to initialize The following items must be initialized for normal system operation in cases such as after the battery is reconnected, or maintenance is performed on the vehicle. Item When to initialize Reference • After reconnecting or changing Moon roof the battery P.
Page 661 6-2. Customization...
Page 662 If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 663 Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English.
Page 665 SRS airbag instructions for Canadian owners (in French) The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instruc- tions in English.
Page 676 National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchas- ers and/or prospective purchasers of Toyota vehicles with infor- mation on truck-camper loading. Your Toyota dealer will help answer any questions you may have as you read this informa- tion.
Page 677 Double Cab models with standard bed Recommended location cargo center of gravity for cargo weight rating Rear end of truck bed Double Cab models with long bed Recommended location cargo center of gravity for cargo weight rating Rear end of truck bed CrewMax models Recommended location...
Page 678 CAUTION ■ Loading precaution If a load is too far back, it can cause dangerous handling. If it is too far forward, the front axle may be overloaded. Cargo weight rating and proper matching When the truck is used to carry a slide-in camper, the total cargo load of the truck consists of the manufacturer’s camper weight figure, the weight of installed additional camper equipment not included in the manufacturer’s camper weight figure, the weight of camper cargo,...
Page 679 ■ Cargo weight rating CWR: Cargo Weight Rating C.W.R Passenger Engine Drive Grade number (lbs) (kg) Standard 1045 1GR- Long 1125 1UR- Standard 1205 Regular Delux 3UR- Long 1450 Standard 1080 3UR- Long 1385...
Page 680 CWR: Cargo Weight Rating C.W.R Passenger Engine Drive Grade number (lbs) (kg) 1GR- Standard Standard 1UR- Standard Standard 3UR- Double Limited Long 3UR- Standard Limited 3UR- Long...
Page 681 CWR: Cargo Weight Rating C.W.R Passenger Engine Drive Grade number (lbs) (kg) 1UR- 3UR- Crew Limited Short 3UR- 3UR- Limited CAUTION ■ Overloading Be careful — overloading can cause dangerous braking and handling problems, and can damage your vehicle and its tires.
Page 682 Gross axle and vehicle weight ratings Secure loose items to prevent weight shifts that could affect the bal- ance of your vehicle. When the truck camper is loaded, drive to a scale and weigh on the front and on the rear wheels separately to determine axle loads.
Page 683 ■ GAWR and GVWR Regular Cab models GAWR Model code ∗ Driving Engine GVWR system type Front Rear GSK50L- 3700 lb. 6200 lb. Standard 4.0L V6 TRADKA (1675 kg) (2810 kg) 3900 lb. (1GR-FE) (1765 kg) GSK51L- 3800 lb. 6400 lb. engine Long THADKA...
Page 684 Double Cab models GAWR Model code ∗ Driving Engine GVWR system type Front Rear 4.0L V6 GSK51L- 3900 lb. 3800 lb. 6400 lb. (1GR-FE) Standard CRASKA (1765 kg) (1720 kg) (2900 kg) engine UPK51L- 3900 lb. 4000 lb. 6700 lb. 4.6L V8 CRTSKA (1765 kg)
Page 685 CrewMax models GAWR Model code ∗ Driving Engine GVWR system type Front Rear UPK51L- 3900 lb. 4050 lb. 6800 lb. 4.6L V8 PSTSKA (1765 kg) (1835 kg) (3080 kg) (1UR-FE) UPK56L- 4000 lb. 4150 lb. 7000 lb. engine PSTSKA (1810 kg) (1880 kg) (3175 kg) USK51L-...
Page 687 What to do if... What to do if... A tire punctures If you have a flat tire P. 623 P. 641 If the engine will not start The engine does not start P. 115 Engine immobilizer system P. 647 If the vehicle battery is discharged If the shift lever cannot be shifted The shift lever cannot be P.
Page 688 What to do if... The warning light or indicator If a warning light turns on P. 609 light comes on ■ Instrument cluster Vehicles with multi-information display Vehicles without multi-information display (type A)
Page 689 What to do if... Vehicles without multi-information display (type B) ■ Center panel...
Page 690: Warning Lights
What to do if... ■Warning lights Brake system warning Power steering warning light light P. 611 (if equipped) Low engine oil pressure warning light P. 609 P. 610 Charging system Master warning light warning light P. 609 P. 613 Malfunction indicator Slip indicator* lamp P.
Page 691: Gas Station Information
GAS STATION INFORMATION Auxiliary catch lever Fuel filler door P. 542 P. 110 Hood lock release lever Tire inflation pressure P. 542 P. 678 Fuel tank capacity 26.4 gal. (100.0 L, 22.0 lmp.gal.) (Reference) Fuel type P. 671 Cold tire inflation P.

Toyota 2012 Tundra Owner's Manual

Quick Links

Related Manuals for Toyota 2012 Tundra

Summary of Contents for Toyota 2012 Tundra

Page 3: For Your Information

Page 690: Warning Lights

Page 691: Gas Station Information