Page 1
Read this manual carefully before operating this vehicle. OWNER’S MANUAL YZF-R6Y 13S-28199-21...
Page 2
EAU46090 Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
Page 3
Welcome to the Yamaha world of motorcycling! As the owner of the YZF-R6Y, you are benefiting from Yamaha’s vast experience and newest technology regarding the de- sign and manufacture of high-quality products, which have earned Yamaha a reputation for dependability.
IMPORTANT MANUAL INFORMATION EAU10132 Particularly important information is distinguished in this manual by the following notations: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
TABLE OF CONTENTS LOCATION OF IMPORTANT Sidestand ........4-27 Tires ..........7-19 LABELS ..........1-1 Ignition circuit cut-off system ..4-28 Cast wheels ......... 7-22 Adjusting the clutch lever free SAFETY INFORMATION ....2-1 FOR YOUR SAFETY – play ........... 7-22 PRE-OPERATION CHECKS ..... 5-1 Adjusting the rear brake light DESCRIPTION ........3-1 switch ........
Page 7
TABLE OF CONTENTS Tail/brake light ......7-35 Replacing a turn signal light bulb ...........7-35 Replacing the license plate light bulb ...........7-36 Auxiliary light ........7-37 Supporting the motorcycle ....7-37 Front wheel ........7-38 Rear wheel ........7-40 Troubleshooting ......7-41 Troubleshooting charts ....7-43 MOTORCYCLE CARE AND STORAGE ..........8-1 Matte color caution ......8-1 Care ..........8-1...
Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer.
SAFETY INFORMATION EAU10283 Safe Riding • Ride where other motorists can Perform the pre-operation checks each see you. Avoid riding in another time you use the vehicle to make sure it motorist’s blind spot. Be a Responsible Owner is in safe operating condition. Failure to Many accidents involve inexperi- As the vehicle’s owner, you are respon- inspect or maintain the vehicle properly...
Page 11
SAFETY INFORMATION due to excessive speed or under- This motorcycle is designed for on- A passenger should also observe cornering (insufficient lean angle road use only. It is not suitable for the above precautions. for the speed). off-road use. • Always obey the speed limit and Avoid Carbon Monoxide Poisoning never travel faster than warrant- Protective apparel...
Page 12
Yamaha accessories, which are avail- of the motorcycle is changed. To avoid to minimize imbalance or instabili- able only from a Yamaha dealer, have the possibility of an accident, use ex- been designed, tested, and approved treme caution when adding cargo or Shifting weights can create a sud- by Yamaha for use on your vehicle.
Page 13
• Accessories fitted to the handle- Use caution when adding electri- genuine Yamaha accessories, recog- bar or the front fork area can cal accessories. If electrical acces- nize that some aftermarket accessories...
Do not expose any key to exces- a Yamaha dealer to have them re-reg- sively high temperatures. istered. Do not use the key with the red Do not place any key close to bow for driving.
INSTRUMENT AND CONTROL FUNCTIONS Keep other immobilizer system EAU10471 EAU38530 Main switch/steering lock keys away from the main switch All electrical circuits are supplied with as they may cause signal inter- power; the meter lighting, taillight, li- ference. cense plate light and auxiliary light come on, and the engine can be start- ed.
Page 19
INSTRUMENT AND CONTROL FUNCTIONS EAU10681 To unlock the steering ECA11020 LOCK NOTICE The steering is locked, and all electrical Do not use the parking position for systems are off. The key can be re- an extended length of time, other- moved.
“ ” warning light may flicker when have a Yamaha dealer check the elec- The corresponding indicator light flash- riding on a slope or during sudden trical circuit. es when the turn signal switch is acceleration or deceleration, but pushed to the left or right.
Page 21
3.0 seconds. If this oc- the coolant temperature in the ra- curs, have a Yamaha dealer check the diator. vehicle. If the engine overheats, see page 7-43 for further instructions.
Page 22
INSTRUMENT AND CONTROL FUNCTIONS Coolant Display Conditions What to do temperature TRIP A Under 39 °C ˚C Message “Lo” is displayed. OK. Go ahead with riding. (Under 103 °F) TRIP A 40–116 °C ˚C Temperature is displayed. OK. Go ahead with riding. (104–242 °F) Stop the vehicle and allow it to idle until TRIP A...
If this occurs, EAU38621 have a Yamaha dealer check the self- Immobilizer system indicator light diagnosis system. (See page 4-10 for The electrical circuit of the indicator...
Page 24
INSTRUMENT AND CONTROL FUNCTIONS multi-function meter unit Tachometer Clock equipped with the following: a speedometer (which shows the riding speed) a tachometer (which shows engine km/h TRIP A speed) an odometer (which shows the to- tal distance traveled) two tripmeters (which show the distance traveled since they were last set to zero) 1.
Page 25
INSTRUMENT AND CONTROL FUNCTIONS Odometer, tripmeter, and stopwatch between the various tripmeter, odome- 3. Push the “SELECT” button again modes ter, and stopwatch modes in the follow- to reset the stopwatch. ing order: F-TRIP → Stopwatch → TRIP A → Split-time measurement TRIP B →...
Page 26
INSTRUMENT AND CONTROL FUNCTIONS Coolant temperature display Air intake temperature display When the air intake temperature display is selected, “A” is displayed before the temperature. Self-diagnosis device TRIP A TRIP A ˚C ˚C 1. Coolant temperature display 1. Air intake temperature display The coolant temperature display indi- The air intake temperature display indi- cates the temperature of the coolant.
Page 27
If the right display indicates any error ror code. codes, note the code number, and then km/h have a Yamaha dealer check the vehi- cle. If the right display indicates error code ECA11590 52, this could be caused by transpon- NOTICE der interference.
Page 28
INSTRUMENT AND CONTROL FUNCTIONS Shift timing indicator light activity: To adjust the brightness of the multi- The indicator light will flash This function allows you to choose function meter displays and tachometer when activated. (This setting whether or not the indicator light 1.
INSTRUMENT AND CONTROL FUNCTIONS 1. Push the “RESET” button to select 1. Push the “RESET” button to select EAU12347 Handlebar switches the desired engine speed for acti- the desired engine speed for deac- vating the indicator light. tivating the indicator light. Left 2.
Page 30
INSTRUMENT AND CONTROL FUNCTIONS Right position. To cancel the turn signal EAU12733 Hazard switch “ ” lights, push the switch in after it has re- With the key in the “ON” or “ ” posi- turned to the center position. tion, use this switch to turn on the haz- ard lights (simultaneous flashing of all EAU12500...
INSTRUMENT AND CONTROL FUNCTIONS EAU12820 EAU12870 EAU33851 Clutch lever Shift pedal Brake lever 1. Clutch lever 1. Shift pedal 1. Brake lever 2. “ ” mark The clutch lever is located at the left The shift pedal is located on the left 3.
INSTRUMENT AND CONTROL FUNCTIONS be sure to set it by aligning a groove on EAU12941 EAU13074 Brake pedal Fuel tank cap the adjusting knob with the “ ” mark on the brake lever. 1. Brake pedal 1. Fuel tank cap lock cover 2.
INSTRUMENT AND CONTROL FUNCTIONS EAU13221 Fuel The fuel tank cap cannot be closed un- Make sure there is sufficient gasoline in less the key is in the lock. In addition, the tank. the key cannot be removed if the cap is EWA10881 WARNING not properly closed and locked.
Your Yamaha engine has been de- signed to use premium unleaded gaso- line with a research octane number of 95 or higher. If knocking (or pinging) oc-...
INSTRUMENT AND CONTROL FUNCTIONS ECA10701 EAU39032 Seats NOTICE Use only unleaded gasoline. The use Rider seat of leaded gasoline will cause unre- pairable damage to the catalytic To remove the rider seat converter. Pull back the rear of the rider seat as shown, remove the bolts, and then pull the seat off.
INSTRUMENT AND CONTROL FUNCTIONS EAU39073 Helmet holding cable 1. Passenger seat lock 1. Projection 2. Unlock. 2. Seat holder 1. Helmet holding cable 2. While holding the key in that posi- 2. Remove the key. 2. Helmet cable holder tion, lift the front of the passenger 3.
INSTRUMENT AND CONTROL FUNCTIONS 3. Pass one of the other snap hooks EAU38943 Adjusting the front fork of the cable through the helmet EWA10180 strap buckle, and then clip the WARNING snap hook onto the cable holder as Always adjust both fork legs equal- shown.
Page 38
INSTRUMENT AND CONTROL FUNCTIONS Spring preload Rebound damping force 1. Current setting 2. Front fork collar 1. Spring preload adjusting bolt 1. Rebound damping force adjusting screw To increase the spring preload and To increase the rebound damping force Spring preload setting: thereby harden the suspension, turn and thereby harden the rebound damp- Minimum (soft):...
Page 39
INSTRUMENT AND CONTROL FUNCTIONS Compression damping force and thereby soften the compression Compression damping setting (for damping, turn the adjusting bolt on fast compression damping): To adjust the compression damping each fork leg in direction (b). Minimum (soft): 4 turn(s) in direction (b)* force (for fast compression damping) Standard: Compression damping setting (for...
INSTRUMENT AND CONTROL FUNCTIONS EAU42942 Spring preload Spring preload setting: Adjusting the shock absorber Minimum (soft): assembly This shock absorber assembly is Standard: equipped with a spring preload adjust- Maximum (hard): ing ring, a rebound damping force ad- justing screw, a compression damping force adjusting bolt (for fast compres- Rebound damping force sion damping) and a compression...
Page 41
INSTRUMENT AND CONTROL FUNCTIONS direction (a). To decrease the compres- Rebound damping setting: Compression damping setting (for sion damping force and thereby soften Minimum (soft): slow compression damping): the compression damping, turn the ad- 20 click(s) in direction (b)* Minimum (soft): Standard: 20 click(s) in direction (b)* justing bolt in direction (b).
1. Luggage strap holder sembly yourself. Take the shock 2. Hook absorber assembly to a Yamaha dealer for any service. 1. Luggage strap holder There are six luggage strap holders, four on the bottom of the passenger seat and one on each passenger foot- rest.
INSTRUMENT AND CONTROL FUNCTIONS EAU41940 EAU15301 below and have a Yamaha dealer re- EXUP system Sidestand pair it if it does not function proper- This model is equipped with Yamaha’s The sidestand is located on the left side EXUP (EXhaust Ultimate Power valve) of the frame.
INSTRUMENT AND CONTROL FUNCTIONS EAU44891 Ignition circuit cut-off system The ignition circuit cut-off system (com- prising the sidestand switch, clutch switch and neutral switch) has the fol- lowing functions. It prevents starting when the trans- mission is in gear and the side- stand is up, but the clutch lever is not pulled.
Page 45
WARNING With the engine turned off: 1. Move the sidestand down. If a malfunction is noted, have a Yamaha 2. Make sure that the engine stop switch is turned on. dealer check the system before riding. 3. Turn the key on.
• If necessary, add recommended coolant to specified level. 7-15 • Check cooling system for leakage. • Check operation. • If soft or spongy, have Yamaha dealer bleed hydraulic system. • Check brake pads for wear. Front brake • Replace if necessary.
Page 47
• Make sure that operation is smooth. • Check cable free play. Throttle grip 7-19, 7-28 • If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing. • Make sure that operation is smooth. Control cables 7-27 •...
Page 48
• Tighten if necessary. Instruments, lights, signals • Check operation. — and switches • Correct if necessary. • Check operation of ignition circuit cut-off system. Sidestand switch 4-27 • If system is not working correctly, have Yamaha dealer check vehicle.
(See page 6-2.) The properly lubricated only when neutral indicator light should come the engine is running. Inade- on. If not, ask a Yamaha dealer to quate lubrication may damage check the electrical circuit. the transmission. 1. Shift pedal 3.
OPERATION AND IMPORTANT RIDING POINTS EAU17213 Parking When parking, stop the engine, and then remove the key from the main switch. EWA10311 WARNING Since the engine and exhaust system can become very hot, park in a place where pedestri- ans or children are not likely to touch them and be burned.
If If you do not have the tools or experi- you are not familiar with vehicle ser- ence required for a particular job, have vice, have a Yamaha dealer perform a Yamaha dealer perform it for you. service.
From 50000 km (30000 mi), repeat the maintenance intervals starting from 10000 km (6000 mi). Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical skills.
Page 55
PERIODIC MAINTENANCE AND ADJUSTMENT ODOMETER READING ANNUAL ITEM CHECK OR MAINTENANCE JOB 1000 km 10000 km 20000 km 30000 km 40000 km CHECK (600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi) √ √ √ √ √ • Check for cracks or damage. 8 * Brake hoses •...
Page 56
PERIODIC MAINTENANCE AND ADJUSTMENT ODOMETER READING ANNUAL ITEM CHECK OR MAINTENANCE JOB 1000 km 10000 km 20000 km 30000 km 40000 km CHECK (600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi) Brake pedal pivot • Lubricate with lithium-soap-based √...
Page 57
PERIODIC MAINTENANCE AND ADJUSTMENT ODOMETER READING ANNUAL ITEM CHECK OR MAINTENANCE JOB 1000 km 10000 km 20000 km 30000 km 40000 km CHECK (600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi) Front and rear brake √ √ √ √...
Page 58
PERIODIC MAINTENANCE AND ADJUSTMENT • Every two years replace the internal components of the brake master cylinders and calipers, and change the brake fluid. • Replace the brake hoses every four years and if cracked or damaged.
PERIODIC MAINTENANCE AND ADJUSTMENT EAU18712 EAU44931 Removing and installing cowl- Cowlings A and B ings and panels To remove one of the cowlings The cowlings and panels shown need 1. Remove the bolts, quick fasteners, to be removed to perform some of the and quick fastener screw.
Page 60
PERIODIC MAINTENANCE AND ADJUSTMENT 1. Quick fastener screw 1. Quick fastener 1. Cowling A 2. Quick fastener 2. Cowling B 3. Remove the forward-most projec- tion from the slot, slide the cowling forward, and then remove the re- maining projections from the slots as shown.
Page 61
PERIODIC MAINTENANCE AND ADJUSTMENT 2. Fit the projections into the slots, 3. Fit the projection on cowling A into slide the cowling rearward, and the hole in cowling B as shown. then fit the forward-most projection into the slot. 1. Cowling A 2.
Page 62
PERIODIC MAINTENANCE AND ADJUSTMENT To install the cowling 1. Fit the slot in cowling C over the projection on the front cowling. 1. Plastic fastener 1. Panel B 2. Projection 2. Bolt 3. Wire harness To install the panel 1. Cowling C 3.
Do not attempt to diagnose wipe off any grime from the spark plug such problems yourself. Instead, have threads. a Yamaha dealer check the vehicle. If a spark plug shows signs of electrode Tightening torque: Spark plug: erosion and excessive carbon or other 12.5 Nm (1.25 m·kgf, 9.0 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT EAU38999 Engine oil and oil filter car- tridge The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter car- tridge replaced at the intervals speci- fied in the periodic maintenance and lubrication chart.
Page 65
5. Remove the engine oil filler cap and drain bolt to drain the oil from An oil filter wrench is available at a the crankcase. Yamaha dealer. 9. Apply a thin coat of clean engine oil to the O-ring of the new oil filter cartridge.
Page 66
PERIODIC MAINTENANCE AND ADJUSTMENT not move correctly and you may Tightening torque: not be able to shift up or down. Engine oil drain bolt: 43 Nm (4.3 m·kgf, 31 ft·lbf) [ECA15342] 14. Refill with the specified amount of the recommended engine oil, and then install and tighten the oil filler cap.
If the oil level warning light flickers EAU39086 or remains on, immediately turn the To check the coolant level engine off and have a Yamaha dealer 1. Place the vehicle on a level sur- check the vehicle. face and hold it in an upright posi- tion.
Page 68
If water has been 2. Remove cowlings B and C. (See added to the coolant, have a page 7-7.) Yamaha dealer check the anti- 3. Place a container under the engine freeze content of the coolant as to collect the used coolant.
Page 69
PERIODIC MAINTENANCE AND ADJUSTMENT 6. Move the hose clamp in the direc- Tightening torque: tion shown, and then disconnect Coolant drain bolt: the radiator hose to drain the radi- 10 Nm (1.0 m·kgf, 7.2 ft·lbf) ator. 13. Pour the recommended coolant into the reservoir to the maximum level mark, and then install the coolant reservoir cap.
17. Start the engine, and then check maintenance and lubrication chart. necessary, have it adjusted by a the vehicle for coolant leakage. If Have a Yamaha dealer replace the air Yamaha dealer. coolant is leaking, have a Yamaha filter element.
Yamaha dealer at the intervals specified in the periodic Tire air pressure maintenance and lubrication chart. The tire air pressure should be checked and, if necessary, adjusted before each ride.
Page 72
* Total weight of rider, passenger, car- if the tire has a nail or glass fragments go and accessories in it, or if the sidewall is cracked, con- tact a Yamaha dealer immediately and EWA10511 WARNING have the tire replaced.
Page 73
After extensive tests, only the tires list- tively poor grip on certain road ed below have been approved for this surfaces until they have been model by Yamaha Motor Co., Ltd. “broken in”. Therefore, it is ad- visable before doing any high- Front tire:...
If any damage is 2. Loosen the locknut at the crank- found, have a Yamaha dealer re- case. place the wheel. Do not attempt 3. To increase the clutch lever free...
PERIODIC MAINTENANCE AND ADJUSTMENT 4. Tighten the locknut. EAU22271 EAU22390 Adjusting the rear brake light Checking the front and rear switch brake pads The front and rear brake pads must be checked for wear at the intervals spec- ified in the periodic maintenance and lubrication chart.
EAU22580 Before riding, check that the brake fluid Checking the brake fluid level touches the brake disc, have a Yamaha is above the minimum level mark and dealer replace the brake pads as a set. replenish if necessary. A low brake fluid...
EAU22760 Changing the brake fluid Drive chain slack ter the brake fluid reservoir when Have a Yamaha dealer change the The drive chain slack should be refilling. Water will significantly brake fluid at the intervals specified in checked before each ride and adjusted...
Page 78
PERIODIC MAINTENANCE AND ADJUSTMENT Using the alignment marks on each chain puller, make sure that both chain pullers are in the same position for proper wheel alignment. Use the end of the swingarm as the reference point for the alignment marks. 3.
If a cable is damaged wet areas. Service the drive chain as or does not move smoothly, have a follows. Yamaha dealer check or replace it. WARNING! Damage to the outer ECA10581 NOTICE sheath may interfere with proper ca-...
PERIODIC MAINTENANCE AND ADJUSTMENT EAU23111 EAU44271 Recommended lubricant: Checking and lubricating the Checking and lubricating the Lithium-soap-based grease throttle grip and cable brake and shift pedals The operation of the throttle grip should be checked before each ride. In addi- tion, the cable should be lubricated at the intervals specified in the periodic maintenance chart.
EWA10731 WARNING If the sidestand does not move up and down smoothly, have a Yamaha dealer check or repair it. Otherwise, the sidestand could contact the ground and distract the operator, re- The operation of the brake and clutch sulting in a possible loss of control.
There is no need to check the electro- ward and backward. If any free lyte or to add distilled water. However, play can be felt, have a Yamaha the battery lead connections need to be dealer check or repair the steering.
Page 84
“OFF”, then discon- To charge the battery nect the negative lead before Have a Yamaha dealer charge the bat- disconnecting the positive lead. tery as soon as possible if it seems to [ECA16302] have discharged.
4. If the fuse immediately blows 2. Remove the blown fuse, and then 7. Spare fuse again, have a Yamaha dealer install a new fuse of the specified Fuse box 2 is located under panel A. check the electrical system.
PERIODIC MAINTENANCE AND ADJUSTMENT EAU39012 Replacing a headlight bulb This model is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. ECA10650 NOTICE Take care not to damage the follow- ing parts: Headlight bulb 1.
Replacing a turn signal light turning it clockwise. This model is equipped with an LED- bulb 7. Have a Yamaha dealer adjust the type tail/brake light. 1. Remove the turn signal light lens headlight beam if necessary. If the tail/brake light does not come on, by removing the screw.
PERIODIC MAINTENANCE AND ADJUSTMENT EAU24312 3. Remove the burnt-out bulb by pull- Replacing the license plate ing it out. light bulb 4. Insert a new bulb into the socket. 1. Remove the license plate light unit 5. Install the socket (together with the by removing the screws.
1. Stabilize the rear of the motorcycle If the auxiliary light does not come on, by using a motorcycle stand or, if have a Yamaha dealer check it. an additional motorcycle stand is not available, by placing a jack un- der the frame in front of the rear wheel.
PERIODIC MAINTENANCE AND ADJUSTMENT EAU24360 3. Remove the brake hose holder on Front wheel each side by removing the bolt and nut. EAU33923 4. Remove the brake caliper on each To remove the front wheel side by removing the bolts. EWA10821 WARNING To avoid injury, securely support the...
Page 91
PERIODIC MAINTENANCE AND ADJUSTMENT Tightening torque: Tightening torque: Brake caliper bolt: Wheel axle pinch bolt: 35 Nm (3.5 m·kgf, 25 ft·lbf) 21 Nm (2.1 m·kgf, 15 ft·lbf) 5. Install the brake hose holders by 12. While applying the front brake, installing the bolts and nuts.
PERIODIC MAINTENANCE AND ADJUSTMENT EAU25080 4. Loosen the locknut on each side of 7. While supporting the brake caliper Rear wheel the swingarm. bracket, pull the wheel axle out, 5. Turn the drive chain slack adjust- and then remove the wheel. EAU44951 ing bolts in direction (a) to loosen NOTICE: Do not apply the brake...
However, should your motorcycle Tightening torque: require any repair, take it to a Yamaha 1. Retainer Drive chain slack adjusting bolt: dealer, whose skilled technicians have 2. Slot 2 Nm (0.2 m·kgf, 1.4 ft·lbf)
Page 94
PERIODIC MAINTENANCE AND ADJUSTMENT heaters or furnaces. Gasoline or gasoline vapors can ignite or ex- plode, causing severe injury or property damage. 7-42...
Remove the spark plugs and check the electrodes. The engine does not start. Have a Yamaha dealer check the vehicle. Check the battery. 4. Battery The engine turns over The battery is good.
Page 96
Start the engine. If the engine overheats again, have a The coolant level Yamaha dealer check and repair the cooling system. is OK. If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant as soon as possible.
Rust and corrosion can develop matte colored finished parts. Be Cleaning even if high-quality components are sure to consult a Yamaha dealer for ECA11142 advice on what products to use be- used. A rusty exhaust pipe may go un- NOTICE fore cleaning the vehicle.
Page 98
MOTORCYCLE CARE AND STORAGE off any detergent residue using pounds for plastic may leave plenty of water, as it is harmful scratches on the windshield. Salt sprayed on roads in the winter may to plastic parts. Test the product on a small hid- remain well into spring.
Page 99
EWA11131 WARNING muffler is normal and cannot be re- moved. Contaminants on the brakes or tires Consult a Yamaha dealer for ad- vice on what products to use. can cause loss of control. After cleaning Washing, rainy weather or humid...
MOTORCYCLE CARE AND STORAGE EAU26181 3. Perform the following steps to pro- 4. Lubricate all control cables and the Storage tect the cylinders, piston rings, etc. pivoting points of all levers and from corrosion. pedals as well as of the side- Short-term a.
Page 103
SPECIFICATIONS Front turn signal light: Taillight fuse: 12 V, 10.0 W × 2 7.5 A Rear turn signal light: Signaling system fuse: 12 V, 10.0 W × 2 10.0 A Auxiliary light: Ignition fuse: 15.0 A License plate light: Radiator fan fuse: 12 V, 5.0 W ×...
Record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehi- cle is stolen. KEY IDENTIFICATION NUMBER: 1.
This informa- b. The use of the vehicle after such tion will be needed when ordering device or element of design has spare parts from a Yamaha dealer. been removed or rendered inoper- ative by any person. 10-2...
Page 106
INDEX Air filter element ........7-18 Front and rear brake pads, checking..7-23 Neutral indicator light ......4-4 Auxiliary light......... 7-37 Front fork, adjusting......4-21 Noise regulation (for Australia)....10-2 Front fork, checking ......7-30 Fuel............4-17 Battery........... 7-31 Oil level warning light ......4-4 Fuel consumption, tips for reducing..
Page 107
INDEX Throttle grip and cable, checking and lubricating ........... 7-28 Tires............7-19 Tool kit ............ 7-1 Troubleshooting........7-41 Troubleshooting charts ......7-43 Turn signal indicator lights ...... 4-4 Turn signal light bulb, replacing.... 7-35 Turn signal switch......... 4-14 Valve clearance ........7-19 Vehicle identification number....
Page 110
YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2008.07-0.3×1 CR...