Summary of Contents for Paradox R885S
- Page 1 Indoor/Outdoor Proximity Reader and Keypad with 10cm (4in) Read Range Stand alone R885S Installation and Operating Instructions V1.1...
-
Page 3: Table Of Contents
Section [203] User Code Programming ....17 Deleting a User Code ........19 Section [204] User Code Reset ......20 User Operation ........21 User Access ........... 21 Panic Alarm ........... 22 User Code Table ........24 Warranty ..........26 R885S 1... -
Page 4: Installation
INSTALLATION To select an installation site: • Avoid wiring the R885S’s cables in the same conduit as AC power cables, lock power or signal wiring. • Reader wiring must remain a minimum of 30cm (12in) away from other wiring, such as wiring for AC power, computer data, telephones, electric locks, etc. -
Page 5: Mounting On Metal Surfaces
MOUNTING ON METAL SURFACES Although the read range may decrease, the R885S can be mounted on metal. However, do not box in or surround the card reader with any kind of metal. If the reader must be installed in a metal enclosure, ensure that the face of the card reader is not covered and that at least 1.6"... - Page 6 For CR-R885-S: red and green Face Light For R885S: blue and green Face Light Weight: 280g (9.8 oz.) Material: Black, UV resistant, ABS plastic Dimensions: 99.5mm (5.75") x 118.5mm (2") x 19.5mm (1") Wire Function: Brown: Not used Black: G round...
- Page 7 Figure 1: Connection drawing (12V Locks) R885S 5...
- Page 8 Figure 2: Connection Drawing (24V Locks) 6 Installation and Operating Instructions...
-
Page 9: Feedback
[1] and [2] keys simultaneously while re- connecting its power supply. The reader will emit a confirmation beep. Repeat this procedure a second time holding the [3] and [4] keys. Sections are reset when the reader emits the second confirmation beep. R885S 7... -
Page 10: Card Presentation Test
CARD PRESENTATION TEST Place the card parallel to t he R885S reader (as shown in the figure) and move it toward the reader until the reader provides audio or visual feedback. 8 Installation and Operating Instructions... -
Page 11: System Programming
5. To program another section, repeat steps 3 and 4. To exit, press and hold the [ CLEAR key for 4 seconds. The reader emits a rejection beep and the green LED turns OFF. R885S 9... -
Page 12: Section [001] Card/Code Options
SECTION [001] CARD/CODE OPTIONS The R885S can function as a reader only, as a keypad only or as a combined reader and keypad. Option [3] by default Enter Description [0] Keypad and reader disabled. For programming only. [1] Reader only. Present valid card to the reader for Access Granted. -
Page 13: Section [003] Access Granted Options
When [1] is programmed, two users are required to obtain Access Granted. Each user must use a valid card, code or both depending on the Card/ Code Option set. Only one user is required to disarm a Panic Alarm. R885S 11... -
Page 14: Dual Access Granted With Dual Panic Disarm
Example: When the reader and the keypad are enabled, User 1 must present a valid card and enter a valid code and then User 2 must present a valid card and enter a valid code for Access Granted. Dual Access Granted with Dual Panic Disarm When [2] is programmed, two users are required to obtain Access Granted (same as Dual Access... -
Page 15: Section [005] Keypad Lockout
0 (disabled) to 7 (7 rapid beep tones). Option [3] by default. SECTION [102] FACE LIGHT INTENSITY The Face Light’s illumination can be adjusted according to the installation’s requirements from 0 (off) to 8 (brightest). Option [4] by default. R885S 13... -
Page 16: Section [103] Face Light Operation
SECTION [103] FACE LIGHT OPERATION The Face Light can be set to remain illuminated continually or can follow the state of the Status LEDs. Option [1] by default. Enter Description Face Light constant. Face Light follows Status LEDs. If [0] in section [103] is selected, this will override options [4] to [7] in Section [004] Display on Card Read on page 12. -
Page 17: Resetting The Installer And Master Codes To Default
Master Code 2 to factory defaults, disconnect the reader’s power supply. Press and hold the [3] and [4] keys simultaneously while re-connecting its power supply. Installer Code, Master Code 1 and Master Code 2 are reset when the reader emits a confirmation beep. R885S 15... -
Page 18: Master Programming
MASTER PROGRAMMING Master Programming Mode is used to program Master and User Codes. SECTIONS [201] AND [202] CHANGING THE MASTER CODES Master Code 1 (default: 111111) is used to program both Master Codes, the User Codes and the Section [002] Door Lock Control (see page 10). -
Page 19: Section [203] User Code Programming
Master Code 1 and 2 can activate cards and program the personal identification numbers (PIN) for the User Codes. The R885S includes 1000 User Codes. User Code 000 to 999 can be 1 to 8 digits in length where each digit can be any value from 0 to 9. - Page 20 the section is empty. If the red LED stays OFF, a User Code is already programmed in the section. 5. Program the card, access code (or both combined) according to the option selected in section [001] (see page 9). Then enable one of the following options: •...
-
Page 21: Deleting A User Code
When you press the [ ] key in step 5: CLEAR If the User Code is not programmed, the R885S will revert to step 4. If a card or PIN was entered, press the [ ] key to Enter confirm the removal and advance to the... -
Page 22: Section [204] User Code Reset
previously been programmed with a PIN/card. If the red LED is ON, the user code is free. 5. Press the [ ] key. CLEAR The red LED flashes. 6. Press the [ ] key to confirm the removal ENTER and advance to the next section. To exit: •... -
Page 23: User Operation
2 users: each user in 1 user: user Keypad turn enters a valid enters a valid Only User Code on the User Code on the keypad and keypad and presses presses the the [ ] key. ENTER ] key. ENTER R885S 21... -
Page 24: Panic Alarm
Single Access Dual Access Granted Granted 1 user: user 2 users: the first Reader presents a valid user presents a valid Keypad card to the card to the reader. reader. The The reader emits a reader emits a confirmation beep confirmation and the green Status beep and the... - Page 25 [ ] key. ENTER The second user has 30 seconds to present a valid card to the reader and then enter a valid User Code. The second user’s card and/or User Code must be different from the first. R885S 23...
-
Page 26: User Code Table
USER CODE TABLE Use this table to keep a record of the User Codes. If you require extra pages, photocopy this table. The PIN column is provided for your convenience, however, we recommend not using it for security reasons. User Name Card Code... - Page 27 User Name Card Code Number (optional) R885S 25...
-
Page 28: Warranty
Your use of the Paradox product signifies your acceptance of all warranty terms and conditions. For the latest product approvals, such as UL and CE, please visit www.paradox.com. © 2010 Paradox Ltd. All rights reserved. Specifications may change without prior notice. PATENTS... - Page 29 Notes R885S 27...
- Page 32 791-1919, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST. For technical support outside Canada and the U.S., call 00-1-450-491-7444, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST. Please feel free to visit our website at www.paradox.com. Printed in Canada - 11/2010 PARADOX.COM R885S-EI05...
Need help?
Do you have a question about the R885S and is the answer not in the manual?
Questions and answers