Table of Contents
Summary of Contents for VideoComm Technologies DT-900
-
Page 1: Quick Start Guide
900MHz Digital Data Radio Series DT-900 / DTX-900 / DTR-900 / DXR-900 QUICK START GUIDE VideoComm Technologies – It’s About Real-Time (888) 379-2666 US Toll Free (905) 336-9665 Phone (905) 336-9662 Fax www.VideoTransmitters.com... -
Page 2: Table Of Contents
Digital Data Radio Quick Start Manual Rev 1.0 TABLE OF CONTENTS TABLE OF CONTENTS…………………………………………………………………..2 CERTIFICATIONS………………………………………………………………………..2 PARTS LIST………………………………………………………………………………..3 SETTING INTERFACE BAUD RATE…………………………………………………..4 RESETTING TO DEFAULT BAUD RATE……………………………………………..5 COMMUNICATIONS TEST……………………………………………………………...6 RS-232 MODE ……….…………………………………………………………………….7 RS-422/485 MODE ……….………………………………………………………………..8 2 WIRE CONFIGURATION……………………………………………………...8 4 WIRE CONFIGURATION……………………………………………………...9 WARRANTY INFORMATION / TERMS &... -
Page 3: Parts List
Please inspect the packaging carefully to ensure you have received all the necessary parts and accessories listed. Refer to the following chart to determine which parts are included with your product. If any parts are missing or damaged, contact VideoComm Technologies’ Customer Service or your re-seller immediately. -
Page 4: Setting Interface Baud Rate
“OFF” position (Down) Connect power and move the power switch to the “ON” position (Up) Launch the VideoComm Technologies software Under the PC Settings Tab, the Baud Rate must be set at 9600 (Default) From the “Modem Configuration” tab, click “Read” to retrieve the current parameters of the radio. -
Page 5: Resetting To Default Baud Rate
Digital Data Radio Quick Start Manual Rev 1.0 RESETTING TO DEFAULT BAUD RATE To reset your 900MHz digital data radios to Manufacturer Default settings: Turn the 900MHz digital data radio(s) “OFF” Turn Dip Switch 1 & 2 “ON” (Up) with Dip Switches 3 though 6 in the “OFF” position (Down) Turn the 900MHz digital data radio(s) “ON”. -
Page 6: Communications Test
Dip switches 2-6 in the “OFF” position (Down) Power the 900MHz Digital Data Radios “ON” Launch the VideoComm Technologies software From the Range Test tab, click “Start” to run the Communications Test After 100+ Packets read “Good” you have successfully completed the Communications Test Remove the serial loop back connector from the receiver. -
Page 7: Rs-232 Mode
Digital Data Radio Quick Start Manual Rev 1.0 RS-232 MODE Confirm the Baud Rate on your third party devices (PTZ Camera, Joystick, DVR) match your Baud Rate settings on the 900MHz data radios. To change the baud rates on the 900MHz Data Radio see page 4. -
Page 8: Rs-422/485 Mode
Digital Data Radio Quick Start Manual Rev 1.0 RS-422 & RS-485 2 WIRE CONFIGURATION Confirm the Baud Rate on your third party devices (PTZ Camera, Joystick, DVR) matches your Baud Rate settings on data radios. See page 4 to change the baud rates Connect the power and antennas to the transmitter &... -
Page 9: Wire Configuration
Digital Data Radio Quick Start Manual Rev 1.0 RS-422 & RS-485 4 WIRE CONFIGURATION Confirm the Baud Rate on your third party devices (PTZ Camera, Joystick, DVR) matches your Baud Rate settings on data radios. See page 1 to change the baud rate Connect the power and antennas to the transmitter &... -
Page 10: Warranty Information / Terms & Conditions
Digital Data Radio Quick Start Manual Rev 1.0 LIMITED WARRANTY VCT hereby warrants, subject to the conditions here in below, that should this product become defective by reason of improper workmanship or material defect during the specified warranty period, VCT will repair the same, effecting all necessary parts without charge for either parts or labor, or replace the unit at VCT option.
Need help?
Do you have a question about the DT-900 and is the answer not in the manual?
Questions and answers