1. Manuals
  2. Brands
  3. Aras Manuals
  4. Security Camera
  5. XC-MD-22V-IR
  6. Quick start manual

Aras XC-MD-22V-IR Quick Start Manual

Network dome camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Camera
Network Dome Camera
Quick Start Guide
XC-MD-22V-IR quick guide
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XC-MD-22V-IR and is the answer not in the manual?

Questions and answers

Summary of Contents for Aras XC-MD-22V-IR

  • Page 1 Camera Network Dome Camera Quick Start Guide XC-MD-22V-IR quick guide...

  • Page 2: Regulatory Information

    About This Document This manual applies to the following model. Model XC-MD-22V-IR This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.

  • Page 3: Fcc Information

    Network Dome Camera·Quick Start Guide FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 4 Network Dome Camera·Quick Start Guide municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union.

  • Page 5: Safety Instruction

    Network Dome Camera·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
  • Page 6 Network Dome Camera·Quick Start Guide ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
  • Page 7 Network Dome Camera·Quick Start Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C, or -40°C ~ 60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.

  • Page 8: Table Of Contents

    Network Dome Camera·Quick Start Guide Table of Contents 1 Appearance Description ..............8 2 Installation ..................10 Disassembling ............... 11 Mounting ..............12 2.2.1 Ceiling Mounting ..........12 Image and Focus Adjusting ..........19 3 Setting the Network Camera over the LAN ........22 4 Accessing via Web Browser ............

  • Page 9: Appearance Description

    Network Dome Camera·Quick Start Guide 1 Appearance Description The overview of the network dome camera is shown below. Overview...
  • Page 10 Network Dome Camera·Quick Start Guide Overview Description Bubble Black Liner Lens Mounting Base Reset Auxiliary Video Output Serial Port Micro SD Card Slot Network Cable Power Cable  Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, and port No., etc.

  • Page 11: Installation

    Network Dome Camera·Quick Start Guide 2 Installation Before you start:  Make sure the device in the package is in good condition and all the assembly parts are included.  Make sure all the related equipment is power-off during the installation.

  • Page 12: Disassembling

    Network Dome Camera·Quick Start Guide ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS.

  • Page 13: Mounting

    Network Dome Camera·Quick Start Guide Mounting 2.2.1 Ceiling Mounting Steps: 1. Disassemble the camera. Refer to the section 2.1. 2. Attach the drill template (supplied) to the place where you want to fix the camera. 3. According to the drill template as shown in Figure 2-2, drill three screw holes in the ceiling.
  • Page 14 Network Dome Camera·Quick Start Guide want to route the cables on the surface of the ceiling. Refer to Conduit Installation on the Side for side cable routing. 5. Attach the camera to the ceiling by aligning the holes of the back box with the holes on the ceiling.
  • Page 15 Network Dome Camera·Quick Start Guide Secure Black Liner and Bubble Conduit Installation on the Side If you want to route the cables from side of the camera, you need to follow the steps below to install a conduit for cable routing. Steps: 1.
  • Page 16 Network Dome Camera·Quick Start Guide Water-proof Plug Side Cable Outlet Remove the water-proof plug 2. Route the power cable and network cable through the side outlet to the conduit. 3. Align and rotate clockwise the conduit to the side outlet tightly. Conduit Install the Conduit to the Camera...
  • Page 17 Network Dome Camera·Quick Start Guide For wall mounting, position the side outlet directly downward for water-proof. Downward Side Outlet Direction...
  • Page 18 Network Dome Camera·Quick Start Guide Mounting Adapter Mounting Base Install the Mounting Base 1. Route the cables through the hole in the center of the wall mount. 2. Align the camera with the mounting base. 3. Tighten the set screws to secure the camera with the mounting base.
  • Page 19 Network Dome Camera·Quick Start Guide Secure Camera 6. Install the inner black liner back to the camera. 7. Align the bubble with the camera. 8. Tighten the screws to secure the bubble with the camera.

  • Page 20: Image And Focus Adjusting

    Network Dome Camera·Quick Start Guide Secure Black Liner and Bubble Image and Focus Adjusting Steps: 1. 3-axis adjustment. View the camera image using the monitor. Rotate the panning table to adjust the panning position of the camera. Rotate the tilting axes to adjust the tilting position of the camera.
  • Page 21 Network Dome Camera·Quick Start Guide Tilting Panning Rotation 3-axis Adjustment 2. Zoom and focus adjustment. View the camera image using the monitor. Loosen the zoom lever and move the lever between T (Tele) and W (Wide) to obtain the appropriate angle of view. Tighten the zoom lever.
  • Page 22 Network Dome Camera·Quick Start Guide Zoom/Focus Lever Lens Adjustment When installing the camera outside, use the XC-RC-MD-01 rain cover, to avoid rain on the dome bubble. It might still happen that the bubble becomes blur, the IR Led might reflect in the camera. To avoid, clean the bubble regularly.

  • Page 23: Setting The Network Camera Over The Lan

    Network Dome Camera·Quick Start Guide 3 Setting the Network Camera over the To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install Xyclop CCTV client software to search and change the IP address of network camera.
  • Page 24 Network Dome Camera·Quick Start Guide computer locates. It displays the total number and information of the searched devices in the Online Devices interface. Go to Device Management, and click Server tab on the left-top of the window, and you can see the online devices listed on the right bottom of the window.
  • Page 25 Network Dome Camera·Quick Start Guide 2). Edit the modifiable network parameters, e.g. IP address and port number. 3). Enter the admin password in the Manager Password field and click OK to save the changes. Modify Network Parameters  The default IP address is “192.0.0.64”. The default user name is “admin”, and the password is “12345”.

  • Page 26: Accessing Via Web Browser

    Network Dome Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari...
  • Page 27 Network Dome Camera·Quick Start Guide Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
  • Page 28 Network Dome Camera·Quick Start Guide Download Plug-in Install Plug-in (1)
  • Page 29 Network Dome Camera·Quick Start Guide Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2-4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera.

Table of Contents