Power Supply; Operating The Light - Stanley SB01AL Instruction Manual

– Do not expose this unit to extremely high temperatures, flames or sparks.
• To reduce the risk of injury, close supervision is necessary when the light is used near children.
• Store idle appliances indoors. When not in use, appliances should be stored indoors in dry and
high or locked-up places – out of reach of children.
• Use of accessories and attachments. Use only attachments recommended or sold by the
manufacturer.
• CHECK DAMAGED PARTS. Before further use of the light, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. A guard or other part that is damaged should be properly repaired or replaced by an
authorized service center unless otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by authorized service center. Do not use light if switch does not turn it on
and off.
• Do not operate this unit with a missing or damaged lens.
• Do not touch the LED surface at any time.
• Never look directly into the light or shine the light into another person' s eyes.
• Do not disassemble the main body of the unit. Other than the 3 "AA" size dry cell batteries, there are
no user-replaceable parts.
WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:
• Carefully follow all instructions and warnings on the battery label and package.
• Always insert batteries correctly with regard to polarity (+ and –), marked on the battery and the
equipment.
• Do not short battery terminals.
• Do not charge batteries.
• Do not mix old and new batteries. Replace all of them at the same time with new batteries of the
same brand and type.
• Remove dead batteries immediately and dispose of per local codes.
• Do not dispose of batteries in fire.
• Keep batteries out of reach of children.
• Remove batteries if the device will not be used for several months.
"Transporting batteries can possibly cause fires if the battery terminals inadvertently come in
contact with conductive materials such as keys, coins, hand tools and the like. The US Department
of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in
commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly
protected from short circuits. So when transporting individual batteries, make sure that the battery
terminals are protected and well insulated from materials that could contact them and cause a short
circuit. "
4
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new Flexible Work Light. Read this Instruction Manual and
follow the instructions carefully before using your new Flexible Work Light.

POWER SUPPLY

The unit is powered by three "AA" alkaline dry cell batteries (supplied). Unscrew the back cover screw
(counter-clockwise) and remove the back cover. Gently pull the battery strap to remove the old
batteries. Pull the strap gently so as not to break it. Insert batteries as described in compartment,
making sure the battery strap is first replaced beneath the new batteries, observing the cautions that
follow. Replace and secure the back cover by screwing the back cover screw clockwise. Do not be over-
tighten.
Note:
Use only "AA" alkaline dry cell batteries in this unit.
CAUTIONS
• When replacing the "AA" alkaline dry cell batteries: DO NOT mix old and new batteries. Always insert
batteries correctly with regard to polarity (+ and –), marked on the battery and the equipment.
Remove dead batteries immediately and dispose of per local codes.
• Follow all warnings regarding batteries in the Important Safety Instructions section of this manual.

OPERATING THE LIGHT

Position the unit, adjusting the flexible stand' s legs or detaching the light and positioning using the
magnetic discs as desired. Press the light mode pushbutton on the top of the unit.
• Press once for high intensity.
• Press again for medium intensity.
• Press a third time for to turn the light off.
• Press and hold the light mode pushbutton for about five seconds for flashing LEDs.
Detaching the light from the flexible stand
TO DETACH THE LIGHT:
• Slide the attachment bar out of the light holder groove.
Once the light is detached, the magnetic discs allow you to position it on any metallic surface.
TO ATTACH THE LIGHT BACK ON THE STAND:
• Slide the attachment bar back into the light holder groove.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• When light is attached using the either the flexible stand or magnetic discs, do not shake the light or
object that it is attached to. Do not attach the light to any electrical wires or anything that it is not
secure.
5