Table of Contents
Advertisement
8 channel stand-alone DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
6. HDD MANAGEMENT
Press [ENTER] button when half-tone green bar is on
HDD MANAGEMENT.
1) HDD CLEAR
When DVMR system started to record and hard drive has
data of pictures recorded, "IN USE" is displayed in square
brackets.
If you want to delete all data on hard drive, press
[ENTER] when half-tone green bar is on "HDD CLEAR".
Then DVMR system asks you to enter password.
Enter password and press [ENTER], and "EMPTY" is
displayed in square brackets.
You are strongly requested to clear data on hard drive,
when you first install hard drive or you add second hard
drive, whether it is used one or brand new one after
setting at FACTORY DEFAULT.
2) HDD INFORMATION
Press [ENTER] button when half-tone green bar is on HDD MANAGEMENT to enter into HDD
INFORMATION.
In HDD INFORMATION, you can have information of HDDs as follows.
- Date of detecting HDD
- Drive number from 1 to 22
- Manufacturer and model of HDD
- Capacity(GB) of HDD detected
3) CD-R BACKUP
Press [ENTER] button when half-tone green bar is on CD-R BACK UP to back up the recorded
data. For more details, please refer to the attached GuideLine paper for this function.
7. MISCELLANEOUS SETUP
Press [ENTER] button when half-tone green bar is on
MISCELLANEOUS SETUP.
In MISCELLANEOUS SETUP, we can set parameters for
buzzer, alarm, timer(time interval), pan/tilt command, baud
rate of RS-485, and password.
1) BUZZER SETUP
In DVMR system, we can set buzzer "ON" or "OFF" for
key, video loss, alarm event, and motion event
independently, in BUZZER SETUP.
Or you can set all of them at "ON" or "OFF" by setting
ALL BUZZER at "ON" or "OFF", by pressing [ENTER}
button.
To save settings and exit, press [MENU] button.
21
3. Operation
HDD MANAGEMENT
HDD CLEAR
[ IN USE ]
HDD INFORMATION
CD-R BACK UP
SELECT
, PRESS ENTER
HDD MANAGEMENT
BUZZER SETUP
ALL BUZZER
---
KEY BEEP
ON
LOSS EVENT
OFF
ALARM EVENT
ON
MOTION EVENT
OFF
SELECT
, EDIT ENTER /
BUZZER SETUP
8 channel stand-alone DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
Chapter 3. Operation
3-1. DVMR SYSTEM log-in
1
Enter the password
default P/W : [ENTER]
ENTER PASSWORD : ________
INPUT YOUR OWN PASSWORD,
2
THEN PRESS [ENTER]
TO EXIT, PRESS [MENU]
Input or modify
Login DVMR SYSTEM
5) Press [ENTER] button after you enter password, to enter into SETUP menu.
6) After entering to setup menu, press [MENU] button to go back to the system menu.
If password entered matches previously set password, "PASSWORD OK" message appears and you
can enter into SYSTEM SETUP.
If password entered does not match previously set password, DVMR system just go back to initial mode,
that is, showing live pictures and recording as set before.
Factory default password is [ENTER]
NOTICE : We recommend you to enter your own password as per procedure in
PASSWORD SETUP/MISCELLANEOUS SETUP of setup menu.
NOTICE : Be sure to memorize the changed password.
In case you forgot password, you can not enter into SYSTEM SETUP and can not
change parameters of DVMR operation, and just leave DVMR unit to run as settings you
done before. In case you forgot own password and want to enter into SYSTEM SETUP,
please contact dealer to get instruction for entering into SYSTEM SETUP for password
change.
10
3. Operation
1) Press [MENU] button to enter the
system menu after starting the system.
2) DVMR system asks you to enter password
to verify authority of user as shown on the
left.
3) When you get the DVMR, you can enter
into Setup menu by just pressing
[ENTER] button.
4) In case you already have changed the
password, enter your own password.
Advertisement
Table of Contents
