Sony DCR-TRV22 Service Manual page 3

www.freeservicemanuals.info
• SUPPLIED ACCESSORIES
Make sure that the following accessories are supplied with your camcorder.
1
4
9
qd
1 AC-L15A/L15B AC Adaptor (1), Power
cord (1)
2 NP-FM30 rechargeable battery pack
(1)
3 A/V connecting cable (1)
4 Wireless Remote Commander
RMT-814
5 R6 (size AA) battery for Remote
Commander (2)
6 Shoulder strap (1)
7 Lens cap (1)
8 Shoe cover (1)
9 "Memory Stick" (1)
MSA-8A
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
5 6
q; qa
qf
0 USB cable (1)
qa CD-ROM (USB Driver)
qs Cleaning cloth (1)
(1)
qd 21-pin adaptor* (1) (AEP, UK, EE, NE model only)
The models with
bottom surfaces only.
qf 2-pin conversion adaptor (1)
*
qg 2-pin conversion adaptor (1)
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
Global electronic heritage manuals
2 3
7 8
qs qd
(1)
SPVD-010 (I) TRV22:US, CND model only
SPVD-010 TRV22:E, HK, BR, JE, KR/
TRV22E model only
mark printed on their
(DCR-TRV22 : JE/TRV22E : JE only)
(DCR-TRV22 : E, HK/TRV22E : E/HK only)
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
— 3 —
19/1/2014
DCR-TRV22/TRV22E
• Abbreviation
CND : Canadian model
AUS : Australian model
JE : Tourist model
KR : Korea model
CH : Chinese model
EE : East European model
NE : North European model
HK : Hong Kong model