Summary of Contents for Easy-Kleen EZN195
-
Page 1: Water Heaters
Natural Gas (EZN) and Propane (EZP) Fired Water Heaters OPERATING MANUAL FOR QUICK REFERENCE, RECORD YOUR MACHINE DATE HERE: Model _ Serial # Volts Phase Date Shipped... -
Page 3: Table Of Contents
Easy-Kleen Pressure Systems 1-800-315-5533 This manual contains operational information that is specific for The EZN and EZP, Natural Gas and Propane fired hot water heaters. Read the following instructions carefully before attempting to assemble, install, operate or service this pressure washer. Failure to comply with these instructions could result in personal injury and/or property damage. -
Page 4: Important Safety Information
IMPORTANT SAFETY INFORMATION The safe operation of our pressure washing systems is the FIRST priority of Easy-Kleen. This will only be achieved by following the operation and maintenance instructions as explained in this manual and all other enclosed manuals. This manual contains essential information regarding the safety hazards, operations, and maintenance associated with this machine. - Page 5 WARNING: Dangerous Gases 3. If you smell gas, shut off the gas supply to the appliance, extinguish any open flame, and test all joints with a soap solution. If the odor persists, call your gas supplier immediately. DANGEROUS GASES WARNING: Keep water spray away from electrical wiring.
- Page 6 WARNING: Trigger gun kicks back. Hold with both hands. 7. Hold firmly to the gun and wand during start up and operation of the machine. Do not attempt to make adjustments while the trigger gun is in operation. 8. Make sure all quick coupler fittings are properly secured before operating pressure washer.
- Page 7 14. Do not attempt to operate this machine if fatigued or under the influence of alcohol, prescription medications, or drugs. 15. Some of the maintenance procedures involved in this machine require a certified technician (these steps are indicated throughout this manual). Do not attempt to perform these repairs if you are not qualified.
-
Page 8: Specifications
AIR RESTRICTION MACHINE BURNER TYPE FLUE OUTLET MODEL # PRESSURE VENT OPENING BTU/HR RING # JETS OF GAS DIAMETER W.C. (in.) @ SEA LEVEL EZN195 195K NONE 8 in EZP195 195K NONE 8 in EZN295 295K NONE 8 in EZN295 295k... -
Page 9: Introduction
EASY-KLEEN MODULAR WATER HEATERS INTRODUCTION Thank you for selecting a quality EASY-KLEEN product. We are pleased to have you included among the many satisfied owners of an EASY-KLEEN SYSTEM. Years of engineering have gone into the development of these fine products and only top quality components and materials are used throughout. -
Page 10: Gas Supply
HIGH LIMIT TEMPERATURE CONTROL The water heater is equipped with a “high limit control” thermostat present at 220 F. It shuts down the burner in the event of excessive outlet temperature caused by insufficient water flow through the heater coil. This control can be adjusted to desired temperature up to but not exceeding 220 F. -
Page 11: Venting Requirements
PROPANE For stationary installations, run a minimum 3/4 IPS supply line as above. For portable applications, a hose and regulator assembly is included with the optional portability kit. This includes a P01 tank connector, single stage regulator and an approved supply hose for connection to a combination gas valve. -
Page 12: Combustion Air Supply
CAUTION: If the heater is left unused for extended periods during sub-zero weather, a column of freezing air will build up in the venting system. If the building has a negative pressure condition, some of the freezing air will be drawn over the draft hood, spilling onto the heating coil which will eventually cause it to freeze and rupture. -
Page 13: Operating Instructions
OPERATING INSTRUCTIONS TO OPERATE MAIN BURNER Be sure water is flowing through water heater coil before turning on burner switch. Start the pumping unit involved until a steady stream of water is flowing from the spray gun. Turn burner switch to “On” position. Burner will ignite and remain in operation as long as there is sufficient water flow to satisfy the pressure switch and temperature limit control. -
Page 14: Burner Maintenance
BURNER MAINTENANCE WARNING: Repair of the burner is to be done by authorized and trained burner professionals only. Due to periodic condensation dripping down onto the burner a scale build up may eventually occur in the burner jet orifices. BURNER REMOVAL Shut off the gas supply line to the water heater. -
Page 15: Component Identification
COMPONENT IDENTIFICATION Flue Outlet Coil Outlet Coil Skin Gas Valve Water Inlet Adjustable Thermostat Safety Relief Valve NG & LPG Heaters • Rev. 4/13/2016... - Page 16 Hot Water Tank Interior (Top Cover Removed): Ceramic Coil Casing Coil Skin (outer Inner Steel steel layer) Layer Coil Outlet (zoomed in view): Hot Water High Limit Outlet Quick Switch Connector Rupture Disk NG & LPG Heaters • Rev. 4/13/2016...
-
Page 17: Trouble Shooting Guide - Burner System
TROUBLE SHOOTING GUIDE - BURNER SYSTEM Problem Cause Remedy a. Check all Fittings with soap a. Gas leak in pilot feed tube solution. b. Ensure that gas supply meets the required pressure for your model b. Low service supply indicated on the SPECIFICATIONS 1. -
Page 22: Manufacturer's Warranty
Pressure Gauges 90 days Within the periods stated above and at the discretion and approval of Easy-Kleen, if there is shown to be a defect in material or workmanship, the defective parts will be repaired or replaced at the manufacturers place of business or an original manufacturers repair depot when returned PREPAID.
Need help?
Do you have a question about the EZN195 and is the answer not in the manual?
Questions and answers