Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for DigiTech XC4134
- Page 1 Serial To Ethernet Converter XC4134 User Manual...
-
Page 2: Table Of Contents
Table of Contents Introduction ……………………………………………..………………… ……4 Overview ………………………………………………………………………….. 5 Package Checklist ……………………………………………………………… 6 Block Diagram ……………………………………………………………………7 Product Features ………………………………………………………………...8 Product Specifications ………………………………………………………… 9 Converter Description & Installation …………………………………11 Product Panel Views …………………………………………………………...11 Left Side …………………………………………………………………………. 12 Right Side ……………………………………………………………………….. 13 LED Indicators …………………………………………………………………..1 4 Wiring Architecture ……………………………………………………………... - Page 3 Menu “Config” …………………………………………………………………19 Web Console Configuration …………………………………………………19 Controller Status ………………………………………………………………22 Controller Setup ……………………………………………………………….24 Controller Updated ……………………………………………………………30 Factory Default Setting ……………………………………………………….31 Self-Testing …………………………………………………………………..32 Hyper Terminal for TCP/IP WinSock …………………………………………33 Hyper Terminal for COM Port ……………………………………………….36 Data Transmission …………………………………………………………….36 …………………………………………………………37 Appendix A - FAQ Appendix B - Pin Outs and Cable Wiring ………………………..38 DC Power Outlet ……………………………………………………………….38...
-
Page 4: Introduction
Introduction We are provides new ways of connecting serial devices to Local Area Network (LAN) or Wide Area Network (WAN). XC4134 TCP/IP converter is designed to operate serial ports over 10/100M Ethernet networks. The data transmitted via TCP/IP protocol. Therefore, control is available via Ethernet, Intranet and Internet. -
Page 5: Overview
Overview XC4134 TCP/IP converter is designed to make your serial devices Internet ready instantly. 8051 Series of XC4134 TCP/IP converter makes ideal choice for connecting your RS-232 or RS-422/485 serial devices—such as PLCs, meters and sensors—to IP-based Ethernet LAN making possible for your software to access serial devices anywhere and anytime over local LAN or Internet. -
Page 6: Package Checklist
Package Checklist 8051 products are shipped with the following items: □ □ 1 unit of XC4134 TCP/IP converter □ □ □ 1 unit of Power Adaptor ( Input :100-240V AC 500mA ) □ (Output :12V DC 1000mA ) □ □ Documentation & Software CD □... -
Page 7: Block Diagram
Block Diagram Low-cost devices are usually equipped with low speed processors and limited memories. In reality, neither having the capability nor practicality to manage complicated the TCP/IP network protocols. 8051 Series is low cost while providing high performance network solution by converting data stream between network TCP/IP and popular serial port signals. -
Page 8: Product Specifications
□ □ Dynamic IP Configuration □ Support DHCP client mode, simplifying network address configuration and management. □ □ Dual LAN Speed □ Support 10/100 Mbps Ethernet, auto-detected. □ □ Server / Client Dual Modes □ 8051 Series can be configured as network server or network client. In the client mode can be installed network which protected by NAT router or firewall, without need a real IP address. -
Page 9: Serial Port
l Ethernet ● Port Type : RJ-45 Connector ● Speed : 10 /100 M bps ( Auto Detecting ) ● Protocol : ARP, IP, ICMP, UDP, TCP, HTTP, DHCP ● Mode : TCP Server ,TCP Client , UDP ● Setup : HTTP Browser Setup (IE & Netscape) RS-232 Console ●... - Page 10 l Power : Input : DC 9 – 12 V l LED Lamp : PWR (Green) l DATA (Red-Blink during data transferring and receiving) l LAN (Red) l SYS (Red-Blink) l Environment : Operating Temperature : 0℃〜60℃ Storage Temperature : -10℃〜70℃ l Dimensions : 85 x 75 x 25 mm ( W x D x H ) l WEIGHT : 110 gm l RoHS :Compliant with RoHS...
-
Page 11: Converter Description & Installation
Converter Description Product Panel Views Terminator DC-In Serial Port Power Outlet RS-485/RS-422 Reset Button Serial Port RS-232 LED Indicators... -
Page 12: Left Side
Connect power line to power outlet at right side of XC4134 TCP/IP converter and put adapter into socket. If the power properly is supplied, the “PWR” green color LED will blink each time in one second. -
Page 13: Right Side
Right Side Terminator Serial Port RS-485/RS-422 Serial Port RS-232 Serial I/O Port of RS-232/RS-422/RS-485 Connect the serial data cable between converter and serial device. Please follow the parameter setup procedures to configure the converter (see the following chapters). Terminator There is terminator resistor built in. If switch 1 & 2 are set in “ON” position, 120 Ohm resistor connected between the signals. -
Page 14: Led Indicators
LED Indicators SYS “Red LED” : Power indicator (When power on, LED will flash each time in one second.) LAN “Green LED” : On-line indicated (When converter is link to LAN then LED will keep on.) 100M- Green LED、10M- Red LED DATA “Red LED”... -
Page 15: Wiring Architecture
Wiring Architecture RS-232 Wiring Architecture RS-232 Wiring Serial Device Converter RS-232 (RTS / CTS) Wiring Serial Device Converter RS-232 (RTS / CTS, DSR / DTR) Wiring Serial Device Converter... -
Page 16: Rs-422/Rs-485
RS-422 / RS-485 Wiring Architecture RS-422 Wiring Serial Device Converter RS-485 Wiring Serial Device Converter When you finish the steps mentioned above and LED indicators as shown, installed converter correctly. You can use Setup Tool “ETM.exe” to setup the IP Address. For proceed setup advanced parameters, please use web browser (IE or Netscape) to continue setting the details. -
Page 17: Converter Configuration
Converter Configuration Initial IP Configuration When first setting up your converter, the first thing you should do is to configure the IP address. This chapter introduces the method to configure the device server’s IP address. For more details about settings network, please see “Web Console Configuration”... -
Page 18: Device Management Utility Of Etm
Device Management Utility of ETM On PC we provide Device Management Utility named ETM.exe which is executable program in Windows 32 bit environments. ETM Setup Tool is used to detect and setup the installed converters. It uses UDP broadcast packets to query and configure converters on the network. When you activate tool, it will detect existence of installed converters and depict the converters’... -
Page 19: Menu "View
Menu “View” □ □ View -> Refresh F5 □ Refresh the status. ETM will send another query to get updated information (see the Figure 3.2). Note: Always run the “View-> Refresh” after change any data. (Figure 3.2) (Figure 3.2) View -> Exit Alt+F4 Exit from the program (see Figure 3.2). - Page 20 Press ENTER or select [IP Address] in the [Config] menu, dialog will be shown (see Figure 3.4). Note: Because ETM uses broadcast UDP packets for sake of security, it allows configuration only when device’s setup password is empty. (Figure 3.4) (Figure 3.4) Assign IP Address with the same Subnet Mask of your computer, avoiding any IP conflict with other network devices.
-
Page 21: Web Console Configuration
Web Console Configuration In addition to basic IP address and subnet mask, specific device setting can be set through HTTP protocol with popular browsers, e.g. Internet Explorer, Netscape, etc. Setup converter as easy as surfing on WWW, no special software will be required. Press [Alt] + [Enter] or select [Device Settings] in [Config] menu, it will open new window in browser to login the device. -
Page 22: Controller Status
Controller Status The Login Page Setup the XC4134 TCP/IP converter as easy as surfing on WWW, no special software will be required. Popular Browsers such as IE or Netscape can easily setup process. In the browser URL field, set the IP address of device directly, to enter the “Controller Status”... -
Page 23: Serial Number
“Reset” button with hold it and turn on the power. The password will be reset to the factory default as “empty”. XC4134 TCP/IP converter uses the same password protection mechanism commonly used in Windows NT or UNIX. If there are more than “3 consecutive failures”... -
Page 24: Controller Setup
Controller Setup □ □ The Setup Page □ Type the correct password in the “Password” field and click [Login] button in the “Controller Status” page, then the “Controller Setup” page will appear (see the Figure 3.7). Note: If you forget the password or can’t login successfully, please contact the manufacturer directly. - Page 25 □ □ IP Address □ The IP address of XC4134 TCP/IP converter, separate by 4 digits do not allow conflict with other devices on the network. If DHCP client mode enabled and there's DHCP server on the network, this field will be assigned by DHCP server automatically.
- Page 26 □ □ Network link speed □ The Physical Ethernet of speed links. “Auto” means the speed is automatically selected by the converter. You can also specify “10Mbps” or “100Mbps” to match the speed of HUB. □ □ DHCP client □ DHCP client mode could be enabled/disabled statues.
- Page 27 Socket type TCP Server: Protocol TCP, open passive to be connected from TCP clients. TCP Client: Protocol TCP, open active to connect the TCP server. UDP: Protocol UDP, connectionless. □ □ Socket port of digital I/O □ Port number A socket port assigned for the serial port. It’s 16-bit number, ranging from 1 to 65535.
- Page 28 □ □ TCP socket inactive timeout ( minutes ) □ We add mechanism - "inactive timeout" to identify whether the socket active or dead. If there is no any data transferred (send / receive) within the timeout defined period (1 to 99 minutes), then it is probably a dead socket and the socket will be closed automatically, thus a new connection can be accepted again.
- Page 29 User assigned ID number for the converter. Available ID is “0 ~ 65535”. □ □ Report device ID when connected □ In TCP mode, if this parameter enabled, every time when the socket connected, XC4134 TCP/IP converter will immediately report its device ID in the following formats: Serial #1 nnnnnA[LF][CR] Serial #2...
-
Page 30: Controller Updated
Controller Updated Press “Update” Button after finishing setting the detailed parameter. The converter will save all parameters into internal non-volatile memory and then reboot (see Figure 3.8). It takes about 5 seconds to complete the whole process and a new login page will be presented (see Figure 3.1). -
Page 31: Factory Default Setting
Factory Default Setting By the chance, if you forget the setup password or setting incorrect the converter inoperable, there are two ways to reset the setting and the following procedures can be used to reset all settings to factory default: 1. -
Page 32: Self-Testing
Self-Testing After completing setting the wiring and parameter, we should verify if setting correct or not. This chapter will introduce how to use single computer to test if the converter behaves well. The operating system can be Windows 95, 98, ME, XP, 2000. The “Hyper Terminal”... -
Page 33: Hyper Terminal For Tcp/Ip Winsock
Hyper Terminal for TCP/IP WinSock Initiate Hyper Terminal from Start Menu in Windows (see Figure 4.1), give terminal name choose an icon and press “OK” button (see Figure 4.2). (Figure 4.1) (Figure 4.2) Select “TCP/IP (Winsock)” option at “Connect using:” field (see Figure 4.3). - Page 34 (Figure 4.3) After pressing “OK” button, Figure 4.4 appears. Enter the converter’s IP address (e.g. 192.168.0.10) at “Host address:” field and set socket port number for Serial Port 1 at “Port number:” field (e.g. 4660). (The Socket type of the Serial Port 1 should be “TCP Server”.) (Figure 4.4)
- Page 35 After pressing “OK” button, Figure 4.5 appears. If Hyper Terminal connects with converter successfully, the time clock at “left lower” corner “connect of hh:mm:ss” will start counting. (Figure 4.5)
-
Page 36: Hyper Terminal For Com Port
Hyper Terminal for COM Port Initiate another Hyper Terminal as COM Port Terminal (in Figure 4.3, select COM 1 or other COM port instead of “TCP/IP (Winsock)”). To set the COM port Properties will as same as Serial Port of converter. (Figure 4.3) Data Transmission When all steps described above are finished, type any characters on the... -
Page 37: Appendix A - Faq
Q. Why can’t ETM.exe detect the converter on network? A. Please check . Power properly plugged to the converter (Please refer “SYS’ LED). . Network cable properly connected between the converter and Hub (Please refer LAN LED). 3. Close Windows or antivirus program firewall (Please refer Device Management Utility of ETM). -
Page 38: Appendix B - Pin Outs And Cable Wiring
Pin outs and Cable Wiring □ □ DC Power outlet □ □ □ RJ-45 Pin Assignment □ □ □ RS-232 Pin Assignment □ The pin assignment scheme for 9-pin male connector on DTE is as show below. PIN 1 : DCD PIN 2 : RXD PIN 3 : TXD PIN 4 : DTR... -
Page 39: Rs-422 Pin Assignment
□ □ RS-422 Pin Assignment □ The pin assignment scheme for 4-pin RS-422 is as show below. 1 2 3 4 PIN 1 : T+ PIN 2 : T- PIN 3 : R+ PIN 4 : R- □ □ RS-485 Pin Assignment □...