IMPOR TANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under- stood by the users, and have therefore not been restated.
MS400 3 7 63 1515 0 DIMENSIONS Remove the cover when you use optional brackets Units: mm L 13942296513 BLOCK DIAGRAM CN203-3(LF-), Mic Input CN203-4(LF+) LOW CUT IC105 P.AMP IC102 Master CN101-6 CN103-6 CN102-6 CN201-6 VR101 VR104 IC104 IC106...
Page 5
MS400 3 7 63 1515 0 PANEL LAYOUT Rear Panel TONE CONTROL HIGH LEVEL LEVEL LEVEL L 13942296513 POWER switch AC IN connector LINE connectors LINE LEVEL control MIC connector MIC control MASTER LEVEL control POWER indicator TONE CONTROL u163 http://www.xiaoyu163.com...
MS400 3 7 63 1515 0 DISASSEMBLY PROCEDURE Amplifier assembly 1-1. Remove the sixteen (16) screws marked [180A]. The amplifier assembly can then be removed. (Fig. 1) Cabinet assembly and buffle assembly 2-1. Remove the nineteen (19) screws marked [170]. The buffle assembly can then be removed from the capinet assembly.
MS400 3 7 63 1515 0 AMP Circuit Boards (1/5 to 5/5) 4-1. Remove the amplifier assembly. (See Procedure 1.) 4-2. Remove the screws and the knob from each circuit board, which can then be removed. (Fig. 2) PCB Name Ref No.
MS400 3 7 63 1515 0 Handle 6-1. Remove the cabinet assembly. (See Procedure 2.) 6-2. Remove the two (2) screws marked [70] and the two (2) nuts marked [80]. The handle can then be removed. (Fig.3) Heat sink 7-1.
MS400 3 7 63 1515 0 AMP2/5 Circuit Board AC IN to Coll (H model only) Pattern side to AMP3/5-CN205 (Component side) Component side L 13942296513 AMP3/5 Circuit Board to Transformer to AMP2/5 -W201A -W201B Pattern side Component side...
Page 14
MS400 3 7 63 1515 0 AMP4/5 Circuit Board LINE PARALLEL to AMP5/5-CN102 +4dB -50dB +4dB L 13942296513 Component side Pattern side u163 3NA: V606200 http://www.xiaoyu163.com...
Page 15
MS400 3 7 63 1515 0 IN2/2 Circuit Board AMP5/5 Circuit Board to AMP1/5-CN201 TONE CONTROL HIGH LIVE LEVEL MIC LEVEL MASTER LEVEL L 13942296513 to AMP4/5-CN101 Component side Pattern side u163 3NA: V606200 http://www.xiaoyu163.com...
Page 16
MS400 3 7 63 1515 0 INSPECTIONS • Amplifier unit Preparation 1) Input terminal LINE INPUT (XLR) MIC INPUT (XLR) 2) Output terminal: CN203 (VH4P) LF 1P(+) 2P(-), RL=4 ohms / Power capacity 500W HF 4P(+) 3P(-), RL=16 ohms / Power capacity 200W...
Page 17
MS400 3 7 63 1515 0 6) Output noise level Ground the input terminals LINE INPUT (XLR) and MIC INPUT (XLR) with a 600 ohm resistance connected to each terminal and measure the noise level at the output terminals LF and HF. The measured value should be as specified below.
Page 18
MS400 3 7 63 1515 0 • Finished product inspection Preparation 1) input terminal: LINE INPUT (XLR) 2) OUTPUT: 3) LINE LEVEL: MAX(10) 4) MIC LEVEL: MIN(0) 5) MASTER LEVEL: MAX(10) 6) TONE CONTROL HIGH: Center click position (0)
3 7 63 1515 0 POWERED SPEAKER MS400 PARTS LIST CONTENTS OVERALL ASSEMBLY ..........2 AMPLIFIRE ASSEMBLY ......... 4 ELECTRICAL PARTS ..........6 L 13942296513 Notes : DESTINATION ABBREVIATIONS A : Australian model M : South African model B : British model...
Need help?
Do you have a question about the MS400 and is the answer not in the manual?
Questions and answers