Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for AMX PT10-PLV
Summary of Contents for AMX PT10-PLV
-
Page 1: Instruction Manual
PT10-PLV Single Camera Pan/Tilt System C a me ra C on t ro l S y s te m s... - Page 2 Consumers should inquire from selling dealer as to the nature and extent of the dealer’s warranty, if any. AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform, including any lost profits, lost savings, incidental damages, or consequential damages.
-
Page 3: Table Of Contents
Table of Contents Table of Contents PT10-PLV Single Camera Pan/Tilt System .............1 PT10-PLV System Components ..................1 Single Camera Configuration with CMA-D2 (up to 25 m)..........3 Installation and Wiring .....................5 Preparing the AXB-PT10 for Communication..............5 Mounting the AXB-PT10....................5 Mounting and Balancing the Camera/Lens ............... - Page 4 Table of Contents PT10-PLV Single Camera Pan/Tilt System...
-
Page 5: Pt10-Plv Single Camera Pan/Tilt System
4-wire (AXlink) data bus. The system can control up to six Sony DXC-390/950 video cameras and store/recall up to 24 presets for each camera. The PT10-PLV Single Camera Pan/Tilt System configuration is the building block for all systems utilizing up to six cameras with Sony CMA-D2/D3 (camera adapters). PT10-PLV System Components... - Page 6 PT10-PLV Single Camera Pan/Tilt System PSN6.5 Power Supply The PSN6.5 NetLinx Power Supply distributes switched-mode 12 VDC power @ 6.5 A to up to three AMX devices. The PSN6.5 supplies power to the AXB-PT10 pan/tilt camera head. AXlink Bus Strip...
-
Page 7: Single Camera Configuration With Cma-D2 (Up To 25 M)
Power to the AXB-PT10 is supplied from the PSN6.5 Power Supply to the unused power pin on the AXB-PT10's AXlink connector. Refer to FIG. 11 for more information about wiring the AXB- PT10 AXlink connector. AMX components in this additional-camera control system include: • AXB-EM232 Master Controller •... - Page 8 PT10-PLV Single Camera Pan/Tilt System Optional accessories: • WM-CAM Wall or Ceiling Mount Adapter (for AXB-PT10) • PM-CAM Pedestal Mount Adapter (for AXB-PT10) • TM-CAM Tripod Mount Adapter (for AXB-PT10) • AC-RK Accessory Rack Kit (for AXB-EM232, AXB-REL8 and AXB-AV2SM)
-
Page 9: Installation And Wiring
Installation and Wiring Installation and Wiring This section covers the steps necessary to connect and operate a PT10-PLV Single Camera Pan/Tilt System. Digital encoders are installed on both the pan and tilt drives, allowing positional feedback for presets, and to provide accurate speed control. Software adjustable stop limits are used to limit the range of motion. - Page 10 3.453" (87.7 mm) 3.00" BHC (76.20mm) 3.45" (87.7 mm) FIG. 4 Mounting-plate dimensions The PT10 can be mounted to camera mounts such as the TM-CAM, WM-CAM, and PM-CAM (Pedestal mount) as shown in FIG. 5. PT10-PLV Single Camera Pan/Tilt System...
-
Page 11: Mounting And Balancing The Camera/Lens
To mount and balance the camera/lens: Do not lift the PT10 by the Camera/Lens cradle as this procedure damages internal components. 1. Remove the camera/lens cradle assembly by removing the four ½" screws and washers from the tilt hub. PT10-PLV Single Camera Pan/Tilt System... - Page 12 8. Take the entire camera/mount and cradle assembly, and align the lens with the Tilt Hub, so the vertical-axis intersects the center of the camera's iris, as shown in FIG. 9. 9. Mark the position of the cradle support bracket on the Tilt Hub (for later attachment). PT10-PLV Single Camera Pan/Tilt System...
-
Page 13: Wiring Information For The Axb-Pt10
AXlink connector. The portion of the power directed toward the pan and tilt motors is fused. The fuses are self-resetting. The AXB-PT10 power rating is 2 amps @ 12 VDC. This power supply must be local. See FIG. 11 for details. PT10-PLV Single Camera Pan/Tilt System... -
Page 14: Wiring Guidelines
AXB-PT10 in the above table are based on a +12 VDC power supply and are capable of 2 amps (continuous) with a maximum current of 20 amps. The PosiTrack unit provides power outputs for the camera/lens combination. PT10-PLV Single Camera Pan/Tilt System... -
Page 15: Using The Axlink Connector For Data And Power
Using the AXlink mini-XLR connector for data and power Wire the Master Controller's AXlink connector to the mini-XLR connector (male) on the rear panel of the AXP-PLV for data and 12 VDC power as shown in FIG. 12. PT10-PLV Single Camera Pan/Tilt System... -
Page 16: Wiring Information For The Axb-Em232
Three blinks/second Indicates that there is an AXlink communication error. Full On Indicates that there is either no AXlink activity or that the AXCESS program is not loaded. PT10-PLV Single Camera Pan/Tilt System... -
Page 17: Putting It All Together
(914.4 m) should use low-capacitance (12-14 pF/ft) shielded twisted pair cable. The length of an AXlink wire run is equal to the total length of wire used; a star run made of one 300' section and six 50' sections equals one 600' AXlink line. PT10-PLV Single Camera Pan/Tilt System... -
Page 18: Axlink - (Local-Area, Low-Power Requirement)
Large systems that power many bus controllers or touch panels should use a heavier gauge wire to handle DC power. Liberty Wire and Cable AMX-2S22218 AXlink Cable, one shielded, twisted pair 22 AWG, 12.5 pF/ft, two 18 AWG, PVC and plenum cable available. -
Page 19: Using The Axp-Plv Positrack Video Pilot
This set of six pushbuttons allows you select which camera (1-6) you External pushbuttons are controlling. The Camera Station selection indicators along the right (right side): edge of the touch panel light to indicate which camera is currently selected. PT10-PLV Single Camera Pan/Tilt System... -
Page 20: Using The Axp-Plv Touch Panel Program
Touch to open the CAMERA CONFIGURATION page, where you can configure a camera for your system. • Camera Station These indicators light to indicate which camera is currently selected (via the selection indicators 1-6 CAMERA STATIONS 1-6 external pushbuttons). PT10-PLV Single Camera Pan/Tilt System... - Page 21 • default button Touch to restore the camera to its default master pedestal, detail and gain set- tings. (This is the same as pressing the Data UP and DOWN buttons simulta- neously on the Sony RM-C950). PT10-PLV Single Camera Pan/Tilt System...
- Page 22 Touch to reverse the current pan orientation on the joystick. • reverse tilt button Touch to reverse the current tilt orientation on the joystick. • SETUP button Touch to access the touch panel Setup screen (for system administrators only). PT10-PLV Single Camera Pan/Tilt System...
-
Page 23: Troubleshooting
RS-232 DIP Switch (S2) Settings Position Function Stop Bits Data Bits Parity Baud Rate 2 bits 7 bits Unused 1 bit 8 bits Unused Unused 1,200 Unused 2,400 Unused 4,800 Even 9,600 19,200 None 38,400 PT10-PLV Single Camera Pan/Tilt System... - Page 24 Troubleshooting PT10-PLV Single Camera Pan/Tilt System...
-
Page 25: Sony Technical Support
Professional Group. Staffed with full-time agents, the center is the focal point of contact for any Broadcast and Professional Group inquiry. The BIC is designed to provide general information, including product specifications, literature and list prices to inquiring callers. Tel: 1-800-686-SONY Email: http://bpgprod.sel.sony.com/cic.htm PT10-PLV Single Camera Pan/Tilt System... - Page 26 Sony Technical Support PT10-PLV Single Camera Pan/Tilt System...
- Page 29 Sony Technical Support PT10-PLV Single Camera Pan/Tilt System...
- Page 30 AMX reserves the right to alter specifications without notice at any time. brussels • dallas • los angeles • mexico city • philadelphia • shanghai • singapore • tampa • toronto • york 3000 research drive, richardson, TX 75082 USA • 469.624.8000 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993...
Need help?
Do you have a question about the PT10-PLV and is the answer not in the manual?
Questions and answers