ECOVACS WINBOT 930 Instruction Manual
  1. Manuals
  2. Brands
  3. ECOVACS Manuals
  4. Ultrasonic Jewelry Cleaner
  5. WINBOT 930
  6. Instruction manual
ECOVACS WINBOT 930 Instruction Manual

ECOVACS WINBOT 930 Instruction Manual

Hide thumbs Also See for WINBOT 930:
Table of Contents

Advertisement

Quick Links

Instruction Manual
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WINBOT 930 and is the answer not in the manual?

Questions and answers

Related Manuals for ECOVACS WINBOT 930

Summary of Contents for ECOVACS WINBOT 930

  • Page 1 Instruction Manual...
  • Page 2 Instruction Manual, please contact our Customer Service Center where a technician can address your specific problem or question. For more information, please visit the ECOVACS official website: www.ecovacs.com The company reserves the right to make technological and/or design changes to this product for continuous improvement.

  • Page 3: Table Of Contents

    Contents 1. Important Safety Instructions...............2 2. Package Contents and Technical Specifications........4 2.1 Package Contents..................4 2.2 Specifications....................4 2.3 Product Diagram..................5 3. Operating the Robot..................6 3.1 Notes Before Cleaning ................6 3.2 Attach the Cleaning Pad ................7 3.3 Assemble the Power Adapter..............7 3.4 Install the Safety Tether................7 3.5 Place the Safety Pod ................9 3.6 Spray Cleaning Solution................9 3.7 Start......................10...

  • Page 4: Important Safety Instructions

    1. Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge on proper use.
  • Page 5 1. Important Safety Instructions 24. Please dispose of used batteries according to local laws and regulations. 25. Do not incinerate the Appliance even if it is severely damaged. The battery can explode in a fire. 26. The Appliance must be used in accordance with the directions in this Instruction Manual. The company cannot be held liable or responsible for any damages or injuries caused by improper use.

  • Page 6: Package Contents And Technical Specifications

    2. Package Contents and Technical Specifications 2.1 Package Contents Benutzerhandbuch Manuale d’Istruzione Mode d'emploi Instruction Manual Safety Pod and Remote Control WINBOT 9 Power Adapter Instruction Manual with Batteries Tether (3) Cleaning Pads WINBOT (1) WINBOT Finishing Cloth Cleaning Solution Extension Cord (1.5m/4’11”) 2.2 Specifications...

  • Page 7: Product Diagram

    2. Package Contents and Technical Specifications 2.3 Product Diagram Robot 1. Power Cord 6. Squeegee 11. Bottom Power Switch 2. Handle 7. Cupule 12. Edge Detection 3. Status Indicator Light and 8. Driving Treads Sensors START/PAUSE Button 9. Wheel Sensor 13.

  • Page 8: Operating The Robot

    3. Operating the Robot 3.1 Notes Before Cleaning Do not use WINBOT 9 on a framed window WINBOT 9 can be used to clean framed or with frame smaller than 5mm (0.2"). frameless glass, larger than 35cm x 60cm (13.8’’ x 23.6’’). If WINBOT 9’s Status Indicator Light If the window is fully covered with dirt, clean flashes GREEN after powering ON, the...

  • Page 9: Attach The Cleaning Pad

    3. Operating the Robot 3.2 Attach the Cleaning Pad 3.3 Assemble the Power Adapter Turn WINBOT 9 over and attach the Cleaning Pad to the Velcro smoothly. Make sure the Cleaning Pad is placed exactly within its Velcro area. 3.4 Install the Safety Tether If WINBOT 9 is used to clean an outside window, the Safety Pod and Tether MUST be used.
  • Page 10 3. Operating the Robot Loop one end of the Safety Tether to End A on the Robot Power Cord and tighten. Connect End A and End B and tighten. Loop the other end of the Safety Tether around the Safety Pod’s channel and pull it tight.

  • Page 11: Place The Safety Pod

    3. Operating the Robot 3.5 Place the Safety Pod The Safety Pod MUST be placed on the inside of the window. Press the Safety Pod FIRMLY on the inside of the window being cleaned. Make sure the Safety Pod is attached securely in place.

  • Page 12: Start

    3. Operating the Robot 3.7 Start Plug in WINBOT 9 Power ON Move the Bottom Power Switch to the “ ” position. WINBOT 9 is powered ON when it beeps and the Status Indicator Light flashes BLUE. Place on the Glass Press the START/PAUSE Button on WINBOT 9’s Handle.

  • Page 13: Pause

    3. Operating the Robot Start P r e s s t h e S T A R T / P A U S E B u t t o n o n WINBOT 9 or on the Remote Control to begin cleaning.

  • Page 14: Stop

    3. Operating the Robot 3.9 Stop When WINBOT 9 completes its cleaning cycle, it returns to the place it started and beeps. Remove WINBOT 9 Power OFF Grasp WINBOT 9’s Handle. Pull the Air Move the Power Switch to the “O” position. Release Trigger and remove WINBOT 9 from the window.

  • Page 15: Maintenance

    4. Maintenance Before performing cleaning and maintenance on WINBOT 9, move the Bottom Power Switch to the “ ” position and unplug it from the receptacle. 4.1 Cleaning Pad Turn the robot over and remove the Cleaning Pad. Rinse the Cleaning Pad and allow it to dry completely before re-attaching it to the robot.

  • Page 16: Driving Treads

    4. Maintenance Cleaning WINBOT 9’s corners Turn the robot over, remove the Cleaning Pad and wipe the four corners of WINBOT 9 with the provided Finishing Cloth. 4.3 Driving Treads Move the Bottom Power Switch to the “ ” Inspect the Driving Treads by using the position.

  • Page 17: Status Indicator Light And Sounds

    5. Status Indicator Light and Sounds Indicator Description Status Indicator Light flashes Back-Up Battery is low and is charging. WINBOT 9 will not clean GREEN until the Back-Up Battery is properly charged. WINBOT 9 is powered ON, suction motor is running, and is ready Status Indicator Light flashes to be placed on the window.

  • Page 18: Troubleshooting

    6. Troubleshooting Malfunction Possible Causes Solutions WINBOT 9 is cleaning. Pause WINBOT 9 by pressing the START/ When WINBOT 9 is PAUSE button on the robot or Remote cleaning, only the START/ Control. Other buttons on the Remote Control PAUSE Button works on the will function when WINBOT 9 is paused.
  • Page 19 6. Troubleshooting Malfunction Possible Causes Solutions A. Connect WINBOT 9 to the Power Adapter and plug into the receptacle. Press START/ PAUSE Button on the robot or on the Remote Control. WINBOT 9 will resume cleaning. B. In case of power failure, and the above solution does not work, WINBOT 9 should Interruption of electricity automatically go back to a place near its start...
  • Page 20 WINBOT 9S-000-IM2014R01...

Table of Contents