Table of Contents
Advertisement
Quick Links
Before attempting to connect or operate this product, read the instructions carefully and save
IHR16-12F2I-S 16 Channel 1080p DVR
this manual for future use.
AHD Digital Video Recorders
Operating Instructions
Premium Series Model Numbers
IHR4-12H1I-S 4 Channel 720p DVR
IHR8-12H1I-S 8 Channel 720p DVR
IHR16-24H1I-S 16 Channel 720p DVR
IHR4-12F1I-S 4 Channel 1080p DVR
IHR8-12F2I-S 8 Channel 1080p DVR
RoHS
Advertisement
Table of Contents
Summary of Contents for Infinique IHR16-12F2I-S
-
Page 1: Operating Instructions
IHR16-24H1I-S 16 Channel 720p DVR IHR4-12F1I-S 4 Channel 1080p DVR IHR8-12F2I-S 8 Channel 1080p DVR IHR16-12F2I-S 16 Channel 1080p DVR Before attempting to connect or operate this product, read the instructions carefully and save this manual for future use. RoHS... -
Page 2: Important Safety Instructions
Important Safety Instructions Please carefully read the following safety instruction to avoid personal injuries and prevent the equipment and other connected devices from being damaged. Power sources (note: please use the power supply included or as specified by the manufacturer). - Page 3 TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY. The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
-
Page 4: Table Of Contents
Table of Contents Important Safety Instructions ......................2 1. Introduction ..........................4 1.1 Features ............................4 2. DVR Overview ..........................5 2.1 Front Panel ............................. 5 2.2 Rear Panel ............................6 2.2.1 Rear panel for DVR with 4/8 Channel DVR ................6 2.2.2 Rear panel for DVR with 16 Channel DVR ................ - Page 5 5.2.1.19 Motion .......................... 27 5.2.1.20 Alarm ..........................28 5.2.2 Record Search ........................29 5.2.2.1 General .......................... 29 5.2.2.2 Time Axis Setup, File Clip and Zoom In/Out ..............31 5.2.2.3 Events ..........................33 5.2.2.4 Quick Backup and Backup .................... 33 5.2.2.5 Play Backup Files ......................34 5.2.3 Device ..........................
-
Page 6: Introduction
Infinique’s Analog HD video recorders are an ideal solution for today’s high demanding video surveillance needs. Infinique’s AHD series DVRs are designed with feature rich capability that takes an advantage of H.264 video compression technology to dramatically reduce the amount of storage and bandwidth while producing excellent image quality. -
Page 7: Dvr Overview
2. DVR Overview 2.1 Front Panel (For reference only, design subjected to change without prior notice) Key or Indicator Functions Power Indicator The “Green” indicator shows that the DVR is powered ON. The “Red” flashing indicator shows that the hard drive is being read or HDD Indicator written to. -
Page 8: Rear Panel
2.2 Rear Panel 2.2.1 Rear panel for DVR with 4/8 Channel DVR (For reference only, design subjected to change without prior notice) Physical Interface Function Video Input To connect CH1-4 (analog) video input devices, standard BNC port Video Output To connect monitor display output , standard BNC port Audio Input To connect CH1-4 audio input signals (microphone), RCA port Audio Output... -
Page 9: Rear Panel For Dvr With 16 Channel Dvr
2.2.2 Rear panel for DVR with 16 Channel DVR (For reference only, design subjected to change without prior notice) Physical Interface Function Video input To connect CH1-16 (analog) video input devices, standard RCA port Video output To connect to a (upper) Main monitor; (lower) SPOT out monitor Audio input To connect CH1-16 audio signal inputs (microphone), RCA port Audio output... -
Page 10: Dvr Connections
3. DVR Connections 3.1 HDD Installation Caution: Please do not take out hard drive when DVR is powered ON! (1) Disconnect the power, and then remove screws on the sides and rear to open DVR upper cover. (2) Connect the data and power connectors of the SATA cable to the main board. Install the HDD to fix it on the bracket and then connect the installed SATA cable to HDD power and the data lines. -
Page 11: Dvr Boot Up
4. DVR Boot Up 4.1 System Initialization After connecting the power cable of DVR to a power outlet, Press the power button to boot the DVR. The system initializing screen will be displayed as shown in Picture 4-1. Picture 4-1 Note：The illustrations shown in user manual may not be the same as the menu interface. - Page 12 Picture 4-3 The IPC setup page allows the users to add and delete IP cameras. Picture 4-4 The Recording schedule page allows the users to set recording time and scheduled recording of DVR. Picture 4-5 The General System Configuration page allows the users to set the general system parameters. TEC-VS-219-1605-V01...
-
Page 13: Main Interface
Picture 4-6 4.3 Main Interface Picture 4-7 Note: When internal HDD is not connected to DVR, “NO HDD” message will appear on the lower part of the main interface and a buzzer alarm is heard. To disable the buzzer alarm, Go to Menu ->Event ->Alarm and disable HDD loss alarm, HDD space insufficiency alarm and set alarm output to “off”. -
Page 14: Dvr Menu
5. DVR Menu Popup Menu After the system initialization, right click the mouse on preview interface or slide the mouse to the bottom of screen to enter into Pop-up Menu. Using this option, Main Menu, Multi-screen, Auto Cruise, Record Search, Sequence, Volume and Brightness setting can be configured, as shown in Picture 5-1. The options in the pop-up menu may vary slightly according to different parameter settings and application environment. -
Page 15: Main Menu Guide
5.1 Main Menu Guide Live Analog Channels Output Display IP Channels Private Zone Record Record Schedule Mainstream Parameter Network Substream Email Network Email Schedule DDNS RTSP Main Menu Motion Alarm Alarm Record Record Search Search Event Search Device General Cloud Storage General Users... -
Page 16: Main Menu
5.2 Main Menu Picture 5-2 In LIVE mode, click the mouse button, or [Menu] button on the remote controller, or click [ ] icon on the toolbar to enter the main menu screen, as shown in Picture 5-2. If system interface is locked, refer to section 5.3 to unlock by entering the password In Main Menu mode, settings for Parameter, Record Search, Device, System, Advanced and Shutdown can be configured. -
Page 17: Ip Channels
Select the channels and click on save button. The DVR will reboot to apply the changes. 5.2.1.2 IP Channels Go to “Main Menu” “Parameter” “Display” “IP Channels” to enter into the menu shown in Picture 5-4. This menu allows the users to configure the IP channels of the DVR. Picture 5-4 Channel : Select Camera channel ... -
Page 18: Live
Manufacturer：Manufacturer information of the IP Camera. Device type: Type of the device connected Protocol： The selected access protocol for camera to connect to NVR MAC Address：Physical address for the device Software：Displays current version of IP Camera. ... -
Page 19: Output
Note：Click Default to set the default color settings. 5.2.1.4 Output Go to “Main Menu”“Parameter”“Display”“Output” to enter into the menu shown in Picture 5-8. Picture 5-8 Video Output: Select the video output mode SeqMode : Select the layout for the sequence mode ... -
Page 20: Record
Picture 5-9 Picture 5-10 5.2.1.6 Record Go to “Main Menu”“Parameter”“Record”“Record” to enter into the menu shown in Picture 5-11. Picture 5-11 TEC-VS-219-1605-V01... -
Page 21: Record Schedule
Channel: Set the desired channel from the drop-down menu Record Switch: Enable/Disable record Pre Record: Enable to pre-record motion Steam Mode: Select the stream, which has to be used for recording for this particular channel. 5.2.1.7 Record Schedule Go to “Main Menu”“Parameter”“Record”“Record Schedule”... -
Page 22: Substream
Picture 5-13 Channel: Select the channel Resolution: Supports three kinds of resolution: 960H/720P/1080P . FPS：PAL: 1~25fps; NTSC: 1~30fps. Bitrate Control: Select the bitrate control method. The available options are CBR and VBR. Bitrate Mode: Select the bitrate mode Select Custom bitrate if CBR mode is selected and select ... -
Page 23: Mobilestream
Audio: Check to enable audio recording if the camera supports audio. Copy: Copy the parameters of the selected channel to any other or all channels. 5.2.1.10 Mobilestream Go to “Menu” “Parameter” “Record” “Mobilestream” to enter into the menu interface, as shown in Picture 5-15 Picture 5-15 Channel: Select the channel... -
Page 24: Capture Schedule
Picture 5-16 Channel: Select channel whose image has to be captured Auto Capture: Enable/Disable automatic capture Stream Mode: Select the stream which is used to capture the image Normal lnterval: Select interval time of Normal capture Alarm lnterval: Select interval time of alarm capture ... -
Page 25: Network
Select the channel and select the type of capture i.e., Normal, Motion or Alarm The capture schedule can be set for the whole week and the schedule of the current channel can be copied to any other channel or all channels to speed up the scheduling process. Note: 1. -
Page 26: E-Mail Schedule
In this menu, users will be able to set parameters like Email address, SSL, Email Enable, Interval and Email Schedule that are used for sending email alerts in case of any events. Refer to Picture 5-19. Picture 5-19 Email: Enable/Disable Email alerts ... -
Page 27: Ddns
Picture 5-20 Select the channel and select the type of event i.e., Motion, Alarm or Exception The Email schedule can be set for the whole week and the schedule of the current channel can be copied to any other channel or all channels to speed up the scheduling process. Note: 1. -
Page 28: Rtsp
Picture 5-21 5.2.1.17 RTSP Go to “Main Menu”“Parameter”“Network”“RTSP” to enter into the RTSP menu interface as shown below. Picture 5-22 Note: The RTSP link format is as follows: Analog Channels: rtsp://ip_address:port/chA/B, IP Channels: rtsp://ip_address:port/ipA/B Where, A:00 for Ch1, 01 for Ch2, 02 for Ch3 etc., B: 0 for Mainstream and 1 for Substream For example, the rtsp link for the mainstream of channel two of the DVR whose ip address is 192.168.0.175 and rtsp address 554 is rtsp://192.168.0.175:554/ch01/0 5.2.1.18 FTP... -
Page 29: Motion
Picture 5-23 FTP Enable: Enable/Disable FTP Server IP: Enter the FTP server address Port: Enter the FTP port Name: Enter the username for the FTP server Password: Enter the password for the FTP server Directory Name: Enter the directory path where the event results are stored ... -
Page 30: Alarm
Enable: Enable/Disable motion detection function Sensitivity: Support levels 1-8, where 8 is the highest level. Buzzer: Enable/Disable buzzer alarm when a motion is detected. The users can choose the buzzer alarm to be raised for 10,20, 40 or 60 seconds) Post Recording: Select the time for which the video has to be recording once the motion is ... -
Page 31: Record Search
Picture 5-26 This menu allows the users to configure the alarm settings. Alarm In: Select the Alarm Input port Alarm Type: Select the Alarm type: Normally Open, Normally Close, and OFF. Latch Time: Set the alarm latch time as10, 20 40 or 60 seconds ... - Page 32 Picture 5-27 Channel: Select the channel to perform search. Type: Select the type of recorded video to play. There are two options, i.e. Normal and Alarm. Start Time/End Time: Select the start time and the end time. The default setting is from 0:00 to ...
-
Page 33: Time Axis Setup, File Clip And Zoom In/Out
Picture 5-28 5.2.2.2 Time Axis Setup, File Clip and Zoom In/Out 1) The Picture 5-29 and 5-30 shows the timeline bar which is used during the playback. Picture 5-29 Picture 5-30... - Page 34 The time axis can be viewed in 24hours, 2 hours, 1 hour, 30 minutes or user-defined mode. Detailed Operation: Fixed Time Axis: If users select [ ] option, the timeline will show two-hour video content. The time range refers to 1 hour before and after the middle point. 2) Backup function and Playback Zoom In/Out function.
-
Page 35: Events
5.2.2.3 Events Go to “Main Menu”“Record Search”“Events” to enter into the menu shown as Picture 5-33. In this menu, users can search the events by date, time, channel and record type. The operations available are as follows: Picture 5-33 : Previous page - Click the button to go to previous page. : Next page -Click the button to go to next page. -
Page 36: Play Backup Files
Select H264 or AVI file type and click Save button to start the backup. Picture 5-35 After backup finishes, Backup Successful message will appear at bottom-left corner, as shown in Picture 5-35. Note: Before backup, make sure that an USB flash disk or other mobile storage devices with USB interface is connected 5.2.2.5 Play Backup Files To play the backed up files,... -
Page 37: Device
: Stop: Click to stop playback. : Next: Click to play the next file. : Previous: Click to play the previous file : Slow Playback: click to play at 1/2, 1/4, 1/8, 1/16 speed. : Fast Playback: click to play at 2×, 4×, 8×, 16× speed. : Open file : Full screen display : Never on top... - Page 38 Picture 5-37 When HDD is connected, the system will automatically detect if HDD is formatted or not; If HDD needs to be formatted, status will be shown as “Not formatted”. Select the HDD and format the HDD. If the system detects that the HDD is already formatted, the HDD status will be shown as “Normal”. See Picture 5-37 No.: Number of HDDs connected to system.
-
Page 39: Ptz Camera Setup
Note: Recording can only be done when HDD is in “Normal” state i.e. when it is formatted and in good working condition. 5.2.3.2 PTZ Camera Setup Go to “Main Menu”“Device”“PTZ” to enter into the PTZ setup menu shown in Picture 5-39. Picture 5-39 Channel: Select a PTZ channel ... - Page 40 Picture 5-40 Picture 5-41 6) Click [Active Cloud] to activate Cloud and you will receive an email with the URL related to Cloud. Click the link that is sent in the email. The following window will open. (See Picture 5-42): Picture 5-42 TEC-VS-219-1605-V01...
-
Page 41: System
7) Click “Allow” (See Picture 5-43): Picture 5-43 8) Click the icon at the upper-left to view the folder (CloudDVR, see Picture 5-44) we created above in step number 4. Picture 5-44 9) Enter the folder to view the pictures captured by DVR (See Picture 5-45) Picture 5-45 5.2.4 System 5.2.4.1 General... -
Page 42: Dst
and Menu Timeouts Picture 5-46 5.2.4.2 DST Go to “Main Menu”“System”“General”“DST” to enter into the DST menu shown in Picture 5-47 This menu allows the user to set DST, Time Offset, Start Time and End Time. Picture 5-47 5.2.4.3 NTP Go to “Main Menu”“System”“General”“NTP”... -
Page 43: Users
Picture 5-48 NTP service: Enable/Disable NTP function. Server Address: Select NTP server (time.windows.com, time.nist.gov, pool.ntp.org). Time Zone: Select the time zone Update Now: Click to update the time Note: When NTP function is set to “Enable”, system will set the system time at every 00:07:50 and every start-up. -
Page 44: User Edit
Username can consist of eight characters and password is composed of numbers 0-9 with max length of eight numbers The administrator is authorized to set common user’s permissions, as shown in Picture 5-50. Picture 5-50 Log Search: allows the users to check all the system logs. ... -
Page 45: Info
Picture 5-51 5.2.4.6 Info Go to “Main Menu” “System” “Info” provides system info as shown in Picture 5-52. Picture 5-52 5.2.4.7 Log Go to “Main Menu” “System” “Log”, provides system log as shown in Picture 5-53. -
Page 46: Advanced
Picture 5-53 Users may search log information by time. Click “Backup” to save all the log information. 5.2.5 Advanced 5.2.5.1 Maintain Go to “Main Menu”“Advanced” “Maintain” to enter into the menu shown in Picture 5-54. Picture 5-54 Auto Reboot: Enable the auto maintenance function to reboot system regularly at every ... -
Page 47: Events
Save Settings: Save the set parameters in the DVR to a removable storage device. Note: Do not take out the USB memory or cut off the power during upgrading. When the update is done, system will automatically restart. The upgrading will take about 5 minutes to finish. It is recommended to load factory default settings after upgrading. -
Page 48: Menu Lock
Picture 5-56 5.3 Menu Lock To lock the menu, click on the icon in the toolbar. To unlock, the users have to input Device ID, User Name and Password on the login interface (Default: User Name: admin, Password: blank). The login screen is as shown in Picture 5-57. -
Page 49: Mute
5.6 Mute Click icon on the toolbar or Mute button on the panel or remote controller to turn ON or OFF the sound from DVR. 5.7 Start Sequence To view channels sequence, click “Start Sequence” icon on the toolbar to start. -
Page 50: Web Application Manager
6. Web Application Manager 6.1 ActiveX control download and installation Open your web browser and input the IP address and Web port number of DVR, for e.g. http://192.168.0.150:81/. If your computer is connected to the internet, it will start to download and install “ActiveX”... -
Page 51: Web Application Manager Login
Picture 6-3 6.2 Web Application Manager Login After the ActiveX controls have been installed, users will be asked to input user name and password, select Main Stream or Sub Stream (In general, select main stream for LAN and sub stream for WAN), and input web port number and select language (See picture 6-4). -
Page 52: Menu Bar
Picture 6-5 6.3.1 Menu Bar The Menu Bar consists of the following tabs Live, Replay, Configuration, Local Setting and Logout. 6.3.1.1 Live Display When the user is logged into the web menu, the<Live> interface will be shown automatically as illustrated in Picture 6-5. Buttons on a single live interface: : Click to mute/unmute : Record switch: Click to start recording instantly. -
Page 53: Video Control
: Play all the Live channels. : Stop all the Live channels : Display previous group of channels : Display next group of channels : Click to maximize the current window to full screen. Right click to pop up menu option and select Exit Full Screen. -
Page 54: Record Search
Picture 6-7 Note: A maximum of four channels can be played simultaneously. 6.3.2.1 Record Search Record playback procedure Select the date you want to check and tick 1 to 4 channels. Any record files in current channel at current date will be displayed in the status bar of the interface. (See Picture 6-8) Picture 6-8 Then select record type (Normal record, Alarm record and All) and channels, and then click “... -
Page 55: Playback Control
Picture 6-9 To playback all the channels synchronously, select “ ”. Otherwise, the users can playback each channel individually. Click to start record playback. When mouse curse is moving on the timeline, the time point of current position will be displayed on the time axis screen. Click the icon to zoom in/out the time bar display ratio, as shown in Picture 6-9 6.3.2.2 Playback Control... - Page 56 Download Full Screen Open all the Stop playing all the playback playback channels Table 6-1 Record file clip During the playback, click icon to clip the selected file; and click again to stop the clip function. Record clip file will be saved as *.264 format. Snapshot function Move the mouse curse to the channel you want to capture, and click [ ] icon to capture the live...
-
Page 57: Remote Setting
Check the record file you want to download and click [Start download] .System will download the record file in sequence and save to local PC. 6.3.3 Remote Setting Click Remote Setting to enter into the interface shown as Picture 6-13 This menu is similar to the main menu of the DVR. - Page 58 Toll Free: +1-855-891-1542 Email: sales@infinique.com © 2016 Infinique. All rights reserved. This product or document is protected by copyright and distributed under licenses restricting its use, copying, distribution and recompilation. No part of this product or document may be reproduced in any form by any means without prior written authorization of Infinique Worldwide Inc and its licensors, if any.