Specifications - Panasonic CQ-C1301NW Operating Instructions Manual

Preparation
1
Set your car's ignition
switch to the ACC or ON
position.
2
Press [SRC] (PWR: Power).
The demonstration screen appears.
Caution
Be sure to select OFF when your car has no ACC position in the ignition switch. Failure to do this
could cause the battery to go dead.
For an ACC-equipped car, select ON.
Settings") The following functions are available. (Default:
off)
The power is turned on automatically when inserting a
¡
disc.
The clock can be displayed even if the power is off.
¡
The 24-hour system is used for the clock.
Notes:
Adjust the clock when "NO CT" appears on the dis-
¡
play.
When a broadcast of FM Radio Data System is
¡
received, the clock is adjusted automatically by the
Clock Time service.
Hold down []]
¡
1
Select the radio AM mode.
[LW/MW]/FM )")
2
Press [DISP].
3
Hold down [DISP] for more than 2 sec-
onds.
4
Adjust the hour.

Specifications

Power supply
Current consumption
Maximum power output
Tone adjustment range
Speaker impedance
Pre-amp output voltage
Pre-amp output impedance
Dimensions (W x H x D) 178 x 50 x 160 mm
Weight
Sampling frequency
DA converter
Pick-up type
Light source
Wave length
Frequency response
Signal to noise ratio
Total harmonic distortion
Wow and flutter
Channel separation
FM
Frequency Range
Usable Sensitivity
Stereo Separation
AM (MW)
Frequency Range
Usable Sensitivity
AM (LW)
Frequency Range
Usable Sensitivity
Notes:
¡ Specifications and design are subject to modification without notice due to improvements.
¡ Some figures and illustrations in this manual may be different from your product.
A C C
(a "Function
or [[] to change numbers rapidly.
(a "Radio (AM
(clock display)
Hour blinks
Hour entered
DC 12 V (11 – 16 V), test voltage 14.4 V, negative ground
Less than 2.2 A (CD mode; 0.5 W 4 channels)
50 W x 4 (at 1 kHz), volume control maximum
Bass: ±12 dB at 100 Hz, Treble: ±12 dB at 10 kHz
4 – 8 Ω
2.5 V (CD mode, 1 kHz, 0 dB)
200 Ω
1.3 kg
8 times oversampling
1 bit DAC System
Astigma 3-beam
Semiconductor laser
790 nm
20 Hz – 20 kHz (±1 dB)
96 dB
0.01 % (1 kHz)
Below measurable limits
75 dB
87.5 MHz – 108 MHz
6 dB/µV (S/N 30 dB)
35 dB (at 1 kHz)
531 kHz – 1 602 kHz
28 dB/µV (S/N 20 dB)
153 kHz – 279 kHz
32 dB/µV (S/N 20 dB)
3
Press [DISP] (Display).
O N
The demonstration screen is cancelled, and no more
appears.
Note: If you would like to turn on the power and make the
demonstration message appear, hold down [SRC] (PWR)
for more than 4 seconds (ACC ON).
[[]: sets the hour ahead.
[]]: sets the hour back.
5
Press [DISP].
6
Adjust the minute.
[[]: sets the minute ahead.
[]]: sets the minute back.
7
Press [DISP].
Clock Display at Power Off
Press [DISP] to change the display. (ACC ON)
Display off
: ACC not equipped (Default)
: ACC equipped
Minute blinks
Minute entered
Completed
Clock display
Clock display