Messages; On The Unit's Display - Panasonic DMR-EX78EB Operating Instructions Manual

Messages

On the Unit's Display

H , F
(" " stands for a service number.)
DVD
(" " stands for a number.)
GUIDE

HARD ERR
NoERAS
NoREAD
NoWRIT
FINAL

PLEASE WAIT

PROG FULL
REMOVE
SP 35:50, LP 151h
"SP", "LP" and the numbers are
examples.
SW-DL

UNSUPPORT

UNFORMAT
F74
F75
U59
U61
U76
U80, U81, U99

The message are alternately displayed.
84
RQT9078
 An error has occurred. The number following "H" or "F" depends on the status
of the unit. Check the items below and in the Troubleshooting Guide. If the
service number still does not disappear after the check, reset the unit (
"To restore the unit if it freezes").
 If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
 The remote control and the main unit are using different codes. Change the
code on the remote control.
 GUIDE Plus+ data is being downloaded.
 If there is no change after turning the unit on and off, consult the dealer
where the unit was purchased.
 You cannot delete items on this disc.
The disc may be damaged. Use a new disc.
 The disc is dirty or badly scratched. The unit cannot record, play, or edit.
 The disc may be incompatible or of poor quality.
 You have used a lens cleaner and it has finished operation. Press
[ OPEN/CLOSE] on the main unit to eject the disc.
 You cannot write to this disc.
The disc may be damaged. Use a new disc.
 When the screen asking if you want to finalise the disc appears, the
message is displayed.
 Displayed when the unit is started. This is not a malfunction.
 The unit is carrying out its recovery process. You cannot operate the unit
while the message is displayed.
 There are already 32 timer recording programmes. Delete unnecessary
timer recording programmes.
 The USB device is drawing too much power. Remove the USB device.
 Available space on the HDD or disc.
The example "SP 35:50" is displayed when less than 100 hours are available and
the example "LP 151h" is displayed when over 100 hours are available.
"SP" and "LP" are recording modes, "35:50" means "35 hours 50 minutes"
and "151h" means "151 hours".
 The unit is performing a software update.
 You have inserted a disc the unit cannot play or record onto.
 You tried to operate with a non-compatible USB memory.
 You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or
DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted.
 The HDMI connection could not be authenticated due to a transfer
malfunction. Consult the dealer where the unit was purchased.
 The HDMI connection could not be authenticated due to an internal data
malfunction. Consult the dealer where the unit was purchased.
 The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes
until the message disappears.
Select a position with good ventilation when installing the unit. Do not block
the cooling fan on the rear of the unit.
 (When a disc is not inserted) Displays when a malfunction has occurred
during recording, playback or copy. This is displayed when the unit is in the
recovery process to return to normal operation; it is not broken. Once the
display disappears you can use the unit again.
 HDMI cannot be output because you are connected to a model that does
not support copyright protection.
 The unit fails to operate properly. Press [/I] on the main unit to switch the
unit to standby mode. Press [/I] on the main unit again to turn the unit on.
Page
−
86,
−
86
76
−
−
81
15, 16
7
−
26
−
−
32
−
−
76
15, 16
17
68
−
−
−
−
−
−