Subscribe to Our Youtube Channel
Summary of Contents for ITC TS-0695
-
Page 1: User Manual
HD Color Video Camera TS-0695 User Manual Please Read This Manual Before Operation... -
Page 2: Safety Tips
Precautions Safety Tips Please read this manual carefully before use the Camera. To avoid damage from stress, violent vibration, soaking during transportation, storage and installation. Take care of each components of Camera during installation, and install camera at where is affordable ... - Page 3 Pan/Tilt Movement Pan Movement: 0-355° Tilt Rotation: Up: 45°, Down: 45° Built in Pan/Tilt Motor: Pan Speed: 1-200°/Second Tilt speed: 1-150°/Second Preset Speed: Pan running: 120°/sec Tilt running: 100°/sec Preset: 64 preset position, 4 Patrol lines Rear board connectors High Definition Interface: HDMI, HD-SDI, DVI, CVBS, YPbPr Controller Signal Interface: 8 leads mini DIN (VISCA IN, VISCA OUT/RS485) Controller Signal Interface: Dip-switch Pin 7/TTL Signal;...
-
Page 4: Dip Switch Settings
Rear Board & function 1. Front View 1) Lens Adopted 10x optical auto focus lens 2) IR Receiver To receive IR mote controller signal LED 3) Power LED LED Blinking when power plug in, Blue color Led 4) Stand by LED LED blinking while shut down camera use remote controller, and Orange color 5) IR Receiver To receive IR mote controller signal LED... - Page 5 When you used RS-485 &PELCO-D to control multi-cameras, suggest to refer to below Camera address code setting table; 5) Switch 6 (Set IR signal output switch) When set as ON, it will receive the signal from remote control and VISCA IN to control this device, if set it to OFF means close signal output.
-
Page 6: Osd Menu
Camera to PC connection Camera Cascade OSD Menu Access OSD menu to understand the features of camera and change the settings. Note: Camera can’t move pan/tilt when OSD menu is displaying on screen. Self-testing OSD Menu INFORMATION There are OSD menu as following when camera start on, and it will be disappear after self-testing completed. -
Page 7: Menu Parameters
Menu Parameters: PAN SPEED Default value: 30 Adjustable pan movement speed scope 1~63 TILT SPEED Default value: 30 Adjustable tile movement speed scope 1~63 SCAN SPEED Default value: 6 Adjustable pan movement speed scope 1~63 TOUR PATH Default value: 1 Optional tour path at 1~4 ... - Page 8 Adjustable scope: 0~255 B GAIN (Blue Gain) Default value: 150 Adjustable scope 0~255 AE (Auto Exposure) Default value: Auto AUTO/MANUAL/SHUTTER/IRIS/BRIGHT SHUTTER SPEED Default value: 1/1 Shutter speed range: 1/1—1/10000 IRIS Default value: Close Close/F1.4-F22 BRIGHT Default value: 0 0 ~ 31 IR Remote Controller...
- Page 9 L-Limit: Set Left limit Scanning position Scan: Enable Boundary scanning R-Limit: Set Right limit scanning position Home: Camera Home position Tour: Enable Patrolling Rev: Image auto-flip Remote controller Function Summary Regional Keynote functions Restart Camera and back to Reset default Factory settings. Camera ID Chose camera according to Chose...
- Page 10 Swift as HDMI Video output (not available with this camera) Swift as DVI Video output (not available with this camera) Swipe different video formats (not available with this camera) Power on/off Power-on/off Login DOME OSD Menu OSD Menu Login Lens OSD Menu Zoom in slowly speed Slow speed Zoom in/out...
-
Page 11: Operation Instruction
Operation instruction Joy-stick PTZ Keybaord operation To use joy-stick PTZ keyboard to control Camera including, pan/tilt/zoom movement, set Tour scanning, enable boundary scanning, etc. option function turn up Down-side movement turn down Up-side movement turn left Left movement turn right Right movement Rotate left Zoom in... - Page 12 Adjust different video format 60Hz mode, camera output 1080p30 as default, support 1080p@30/25/20/15/10/5, 720p, 800x600, 640x480/60/50/30/25/20/15/10/5; 50Hz mode, camera output 1080p@25 as default, support 1080p@25/20/15/10/5, 720p, 800x600, 640x480/50/25/20/15/10/5; The Camera upgrade (control) Install the HD Camera Debugger Tool in your PC while connected VISCA IN of Camera to RS232 at PC, please refer to follow Steps: Connected Camera (VISCA IN) to PC (RS-232) with RS232 Cable which provided along with Camera in the Package;...
-
Page 13: Specification Sheet
Specification sheet Model No. TS-0695 Image Sensor 1/2.8" Type Exmor CMOS Effective Pix 3.27 Megapixel Min. Illumination 0.5Lux White balance Auto/Manual Image Sensor Gain control Auto/Manual B/L compensation On/Off Shutter speed 1/1 - 1/10,000S S/N ratio >50db Focus f=4.7-90mm F1.6-3.5... -
Page 14: Installation Instruction
Installation instruction Desktop Installation Put the camera on the desk flat, and make sure the camera in level. If wan to put the camera on oblique surface, please make sure the angle of inclination less than 15 degree for ensure camera pal and tilt working in normal operation. Tripod Installation Twist the tripod’s screw on the camera tripod hole, then the tripod could be installed on the bottom of camera. - Page 15 Step 2: Fixed the Use the screws to fix Slotted screws deltaic bracket. the deltaic bracket with the bottom plate of camera. Deltaic bracket Step 3: Connect the deltaic bracket to quadrate bracket. Use hand prop the camera, let the slotted screw nut through the groove of quadrate bracket.
-
Page 16: Troubleshooting
Troubleshooting Before bringing in your camera for service, check the following as a guide to troubleshoot the problem. If the problem cannot be corrected, consult with your Dealer. Symptom Cause Remedy The supplied AC power adaptor is not connected to the DC IN 12V jack firmly, or The power of the Insert the power cord firmly as far as it the AC power cord is not inserted firmly...
Need help?
Do you have a question about the TS-0695 and is the answer not in the manual?
Questions and answers