Page 1 O w n e r ’ s Ma n u a l 2 0 1 5 G a s o l i n e...
Page 2 P A R T N U MB E R P T 0 1 8 6 3 5 OWN E R ’ S MA N U A L C o p y r i g h t 2 0 1 5 b y Mo b i l i t y V e n t u r e s L L C N o p a r t o f t h i s ma n u a l ma y b e r e p r o d u c e d i n a n y f o r m, b y p h o t o s t a t , mi c r o f i l m, x e r o g r a p h y , o r a n y o t h e r me a n s , o r i n c o r p o r a t e d i n t o a n y i n f o r ma t i o n r e t r i e v a l s y s t e m, e l e c t r o n i c o r me c h a n i c a l , w i t h o u t t h e...
Page 3: Table Of Contents
Warranty Table of Contents Page MV-1 Limited Warranty ��3 Who Makes these Warranties ��3 When these Warranties Begin ��3 Warranty Periods ��3 What is Covered ��3 Items Not Covered by Warranty ��6 Tire Warranty ��6 Federal Requirements for Emissions Warranties ��6 Federal Emissions Defect Warranty Coverage ��7...
Page 4 Table of Contents Page Explanation of California Emissions Warranties �� 11 Manufacturer’s Warranty Coverage �� 11 Owner’s Warranty Responsibilities ��12 What is Covered by the California Emissions Defect Warranties? ��12 What is Not Covered by the California Emissions Defect Warranties? ��13 Limitations and Disclaimers ��14 Mobility Ventures’...
Page 5: Mv-1 Limited Warranty
What is Covered Except for those items specifically excluded herein, these war- Your MV-1 is protected by an express limited warranty for a pe- riod of 3-years or 36,000 miles, whichever comes first, except for ranties cover the repair or replacement of any parts exhibiting the Powertrain and Wheelchair Access Ramp.
Page 6 Power Swing Door Battery Mobility Ventures will warranty the original equipment battery Mobility Ventures warrants that the Power Swing Door and all for the term of 3-years or 36,000 miles, whichever comes first. related mechanisms are covered for a term of 3 years or 36,000 miles, whichever occurs first.
Page 7 Powertrain • Timing Chain • Valve Covers The Mobility Ventures Powertrain Warranty coverage applies to the repair or replacement of major internal components or assem- • Water Pump blies of the engine, transmission and drive axle. Powertrain War- Transmission/Drive Axle ranty coverage is for 5 years or 60,000 miles, whichever comes first.
Page 8: Items Not Covered By Warranty
The repairs listed below are not covered under the New Vehicle Limited Warranty: Your MV-1 is in compliance with Federal Emissions require- ments and is covered by the Emissions Defect Warranty and the • Damage Due to Accidents, Misuse or Alterations Emissions Performance Warranty.
Page 9: Federal Emissions Defect Warranty Coverage
• Your vehicle has not been tampered with, misused or abused. onboard emission diagnostic module. The warranty coverage period for the MV-1 is: • 3 years or 36,000 miles (whichever occurs first) for all other • 8 years or 80,000 miles (whichever occurs first) for catalytic covered parts.
Page 10: What Is Covered By The Federal Emissions
• 2 years or 24,000 miles (whichever occurs first) for all other • Evaporative Emission Control System covered parts. • Exhaust Manifold See below for a list of covered parts. • Fuel Filler Cap and Neck Restrictor Note that the warranty period begins the date you receive your new •...
Page 11: What Is Not Covered By The Federal Emissions Performance Warranty
Warranties (whichever occurs first). Your authorized defect or has failed because of abuse, neglect, improper mainte- MV-1 service center maintains a complete list of parts covered nance, unapproved modifications, or any items included in Items by emissions warranties. For more details about the specific parts Not Covered by Warranty on page 6.
Page 12: California Requirements For Emissions Warranties
Ventures will provide you with a written explanation of reasons within the shorter of (1) 30 days from the date of presentment to the authorized MV-1 service center, or (2) the time required by Vehicles Eligible for California Emission law for your vehicle to be repaired without incurring further pen- Warranty Coverage alty.
Page 13: Explanation Of California Emissions Warranties
The California Air Resources Board and Mobility Ventures are pleased to explain the emission control system warranty on the – If your MV-1 fails a Smog Check inspection, all necessary vehicle. In California, new motor vehicles must be designed, repairs and adjustments will be made by Mobility Ventures built, and equipped to meet the State’s stringent anti-smog stan-...
Page 14: Owner's Warranty Responsibilities
• Cold Start Enrichment System sponsibilities, or if you want to report what you believe to be • Controls for Deceleration violations of the terms of this warranty, you may contact MV-1 • Electronic Ignition System Customer Assistance at 1-877-MV1-FORU (877-681-3678) or the California Air Resources Board at: •...
Page 15: What Is Not Covered By The California Emissions Defect Warranties
• Fuel Injection System Important Information about List of Parts • Fuel Tank* There may be additional coverage for these parts through the Bumper-to-Bumper or Powertrain limited warranties. In any case, • Ignition Coil and/or Control Module the warranty with the broadest coverage applies. Also covered •...
Page 16: Limitations And Disclaimers
Customer Assistance and Dispute Resolution THESE WARRANTIES ARE IN LIEU OF ALL OTHER Satisfaction with your new MV-1 is very important to us. If you OBLIGATIONS, LIABILITIES OR WARRANTIES, EX- have a problem with your vehicle, please follow these steps: PRESS OR IMPLIED.
Page 17 You may contact the BBB AUTO LINE at: MV-1 Customer Service will work with your service center to try and resolve your issue. BBB AUTO LINE Program Step 3 Council of Better Business Bureaus, Inc. 3033 Wilson Blvd. If we are unable to resolve the problem, you may file a claim with Suite 600 the Better Business Bureau (BBB) Auto Line Program.
Page 18: Notice To California Purchasers
Notice to California Purchasers The BBB claims resolution process normally results in a decision within 40 days from the time a claim is filed. There may be a Mobility Ventures participates in the Better Business Bureau delay of 7 days if you did not first contact Mobility Ventures LLC (BBB) AUTO LINE Program.
Page 19 Introduction/Features Table of Contents Page Welcome ��19 General Information ��19 Vehicle Symbol Glossary ��20 Warranty Information ��23 Safety Information ��23 General Vehicle Information ��23 Warning Labels ��24 Emission Control Information Label��27 Safety Certification Decal ��28 Exhaust and Chemical Warning ��29 Federal Highway Administration Regulation ��29 Reporting Safety Defects��29 California Proposition 65 Warning ��30...
Page 20 Table of Contents Page Table of Contents Page Impaired Driving ��31 Illuminated Entry ��38 Drugs ��31 Cup Holders��39 Alcohol ��31 Grab Handles ��39 Distracted Driving ��32 Coat Hooks ��39 Passive Anti-Theft System (PATS) ��32 Sun Visors ��39 Automatic Arming ��33 Storage ��40 Automatic Disarming ��33 Audio System ��40...
Page 21: Welcome
Also, have anyone else who may be operating your in every way. The MV-1 was designed from the ground up for vehicle read the manual in its entirety. When you have finished wheelchair accessibility, and it is proudly built in America.
Page 22: Vehicle Symbol Glossary
VEHICLE SYMBOL GLOSSARY These are some of the symbols you may see on your vehicle. Air Conditioning Brake System Warning Light Door Lock Air Recirculation Charging System Door Unlock Airbag Readiness Child Seat Lower Anchor Engine Coolant Anti-lock Brake System Child Tether Anchor Engine Coolant Temperature Autolamps OFF...
Page 23 Fuse Compartment Low Tire Pressure Warning Power Swing Door Hazard Warning Flasher Maintain Correct Fluid Level Ramp Controls OFF Headlamps Master Lighting Switch Rear HVAC ON High Beams Outside Power Mirrors Rear Window Defrost Hood Release Panel Dimmer Control Rear Window Washer Horn Panic Alarm Rear Window Wiper...
Page 24 Service Engine Soon Window Auto Shield Eyes from Explosive Window Lock Out Gases Short Ramp Deploy Windshield Defrost/Demist Tow/Haul ON Windshield Washer Traction Control/ Windshield Wiper Electronic Stability Control Traction Control System OFF Turn Signals Vehicle System Malfunction Indicator Light Warning Introduction/Features...
Page 25: Warranty Information
WARRANTY INFORMATION GENERAL VEHICLE INFORMATION General information about your MV-1, such as the Vehicle Identi- Warranty information is available in Section 1. Read the section fication Number (VIN), model code and paint code can be found carefully to learn the warranty coverage on your vehicle and to on the Service Parts Identification label.
Page 26: Warning Labels
WARNING LABELS This warning is imprinted onto the coolant surge tank. Warning labels are located on the vehicle to alert the opera- tor and/or any service technicians who may be working on the vehicle to potential safety hazards that exist, and to the related precautions that must be taken.
Page 27 This warning decal is printed on the coolant surge tank cap. This warning is located on both of the battery caps. DANGER/POISON MEDICAL HELP FAST 15-WOM02-002 Introduction/Features...
Page 28 This warning is located on the steering fluid reservoir cap. This warning is located on the brake fluid reservoir. 15-WOM09-004 15-WOM02-001 Introduction/Features...
Page 29: Emission Control Information Label
EMISSION CONTROL INFORMATION LABEL This refrigerant warning is located by the battery. The Vehicle Emission Control Information Label for the gasoline engine is located under the hood. Introduction/Features...
Page 30: Safety Certification Decal
SAFETY CERTIFICATION DECAL The safety certification decal is located on the edge of the driver’s side door. The decal is required by the National Highway Traffic Safety Administration (NHTSA) and includes a self-destructive, tamper-proof feature. If the decal is tampered with, a “VOID” pattern will appear across the decal.
Page 31: Exhaust And Chemical Warning
Traffic Safety Administration (NHTSA) in addition to noti- addition, certain fluids contained in vehicles and certain products fying Mobility Ventures, either at service@mv-1.us, or at (877) MV1-FORU (877-681-3678). If NHTSA receives similar com- of component wear contain or emit chemicals known to the state plaints, it may open an investigation.
Page 32: California Proposition 65 Warning
Material – Special handling may apply for service or vehicle age to the vehicle, interfere with the vehicle’s electrical system or end-of-life disposal. may void the MV-1 New Vehicle Limited Warranties. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Introduction/Features...
Page 33: Impaired Driving
IMPAIRED DRIVING Drinking and driving is very dangerous and could cause seri- ous injuries or death to yourself or others. Statistics reveal that Drugs about half of all motor vehicle fatalities are alcohol-related. Over WARNING 20,000 motor vehicle-related deaths occur each year because DO NOT drive when under the influence of drugs.
Page 34: Distracted Driving
DISTRACTED DRIVING PASSIVE ANTI-THEFT SYSTEM (PATS) WARNING Your MV-1 is equipped with a passive anti-theft system, which is an engine immobilization system. This system is designed to Use extreme caution when using any device that may take your focus off of the road. Your primary responsibility as the driver is help prevent the engine from being started unless a coded key the safe operation of your vehicle.
Page 35: Automatic Arming
Automatic Arming KEYS When the ignition is switched to the off position vehicle is imme- The key operates all locks on your vehicle. You should always diately armed against being started with anything but a coded key. carry a second key with you in a safe place in case you require it in an emergency.
Page 36: Replacement Keys
Replacement Keys Turn the ignition from the ON position back to the OFF posi- tion in order to remove the first coded key from the ignition. If your keys are lost or stolen and you don’t have an extra coded Within 10 seconds of removing the first coded key, insert the key, you will need to have your vehicle towed to an authorized second previously programmed coded key into the ignition...
Page 37: Remote Entry System��35 Maintenance And Service
REMOTE ENTRY SYSTEM The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range The remote entry system allows you to lock or unlock all vehicle could be caused by: doors without a key. •...
Page 38: Locking The Doors
Switching from Two Step to One Step Door Unlocking Sounding the Panic Alarm Your MV-1 comes with two step un- locking enabled. With the vehicle Press to activate the alarm. Press the control again, or turn the...
Page 39: Replacing The Battery
Replacing the Battery 3. Remove the old battery. NOTE: The remote entry transmitter uses one coin-type three-volt lithi- Please refer to local regulations when disposing of trans- um battery CR2032 or equivalent. mitter batteries� 4. Insert the new battery. Refer to the diagram inside the re- To replace the battery: mote entry transmitter for the correct orientation of the Twist a thin coin be-...
Page 40: Illuminated Entry
If the locks still fail to respond, contact an tion from the 1 (OFF) posi- tion to the 3 (ON) position MV-1 Service Center. four times in rapid succession (within 6 seconds) with the Illuminated Entry...
Page 41: Cup Holders
CUP HOLDERS GRAB HANDLES There are up to five cup holders in your MV-1. There are two in There are three grab handles in the MV-1 to make entering and the passenger’s right side dash panel, two on either side of the exiting the vehicle easier.
Page 42: Storage
STORAGE AUDIO SYSTEM Your MV-1 has three stor- Your MV-1 may be equipped with one of two audio systems: age areas located in dash The MP3 CD Player/Receiver in the middle and on the passenger side of the vehi- cle, as shown on the right.
Page 43: Auxiliary Power Point (12V
• do not use the power point longer than necessary when the engine is not running, Your MV-1 is equipped with up to five auxiliary power points. • do not leave battery chargers, video game adapters, comput- All the power points are capped as shown and can be found in the...
Page 44: Backup Camera
The Backup Camera display has three zones indicated on it, which will give you an idea of how far away objects are from Your MV-1 may be equipped with a Backup Camera to aid in the rear of your MV-1. Objects are closest to your vehicle when increasing your field of vision when backing up your vehicle.
Page 45 If you do not get an image while in reverse, or the image stays on after you have shifted out of reverse, have the Backup Camera checked at an authorized MV-1 service center. Introduction/Features...
Page 46 VEHICLE IDENTIFICATION NUMBER (VIN) The vehicle identification number (VIN) is located on the driver’s side instrument panel and is visible through the windshield. NOTE: In the graphic XXXX is representative of your vehicle identification number. The VIN can also be found on the Service Parts Information Label on the edge of the passenger side front door.
Page 47 5 7 W M S 2 C 6 0 F M 000001 GVWR Check 6 = 6600 lbs Vehicle Line Digit (2994 kg) M = MV-1 Plant Location Series Engine Type M = Mishawaka World S = S Series Manufacturing C = V6 Gasoline 3.7 Liters;...
Page 49: Instrument Cluster
Instrument Cluster Table of Contents Page Warning Lights ��49 Service Engine Soon ��49 Brake System Warning Light ��50 Anti-Lock Brake System (ABS) ��50 Traction Control System (TCS)/ Electronic Stability Control System (ESC) ��50 Engine Oil Pressure ��51 Low Fuel ��51 Airbag Readiness ��51 Low Tire Pressure Warning ��51 Charging System ��51...
Page 50 Table of Contents Page Table of Contents Page BTSI (Brake Transmission Shift Interlock) Warning Trip Odometer ��55 Chime ��52 Tachometer ��55 Liftgate Chime ��52 Fuel Gauge ��55 Power Swing Door Chime ��52 Power Ramp is Deployed Warning Chime ��52 Power Ramp Obstacle Warning Chime ��52 Power Ramp Deployment or Retraction Chime ��52 Indicator Lights ��53 Turn Signals ��53...
Page 51: Warning Lights
Many lights will illuminate when you tion occurs, drive in a moderate fashion (avoid heavy acceleration start your MV-1 to make sure the bulb works. If any light remains and deceleration and have your vehicle serviced immediately by on after starting the vehicle, refer to the respective system warn- your authorized service center�...
Page 52: Brake System Warning Light
Brake System Lights Anti-Lock Brake System (ABS) If the ABS light stays illuminated or continues to WARNING flash, a malfunction has been detected and the system Driving a vehicle with a Brake System Warning light on is danger- ous. should be serviced immediately by your authorized REASON: service center.
Page 53: Engine Oil Pressure
Engine Oil Pressure stantly on, have the Tire Pressure Monitoring System (TPMS) inspected by your authorized service center. For more informa- Displays when the oil pressure falls below the normal tion on this system, refer to Tire Pressure Monitoring System range.
Page 54: Warning And Indicator Chimes
WARNING AND INDICATOR CHIMES Liftgate Chime Key-in-Ignition Warning Chime Sounds five times as the Liftgate is opening and closing. Sounds when the key is left in the ignition in the OFF or ACCES- Power Swing Door Chime SORY position and the driver’s door is open. Sounds as the Power Swing Door is opening and closing with a Headlamps On Warning Chime long chime when the process is complete.
Page 55: Indicator Lights
INDICATOR LIGHTS High Beams Illuminates when the high beam headlights are turned Traction Control OFF Illuminates when the Traction Control feature has been turned off. Remains illuminated until Traction Control has been turned on. Tow/Haul Indicator lights illuminate to remind you to perform a function or Illuminates when Tow/Haul is on.
Page 56: Engine Coolant Temperature Gauge
GAUGES WARNING Never remove the coolant reservoir cap while the engine is run- ning or hot. Coolant Reservoir Cap Engine Coolant Temperature Gauge Indicates engine coolant temperature. At normal op- erating temperature, the needle will be in the normal 15-WOM09-005 range (between “H”...
Page 57: Fuel Gauge
Speedometer Fuel Gauge Indicates the current vehicle speed in miles per hour Indicates approximately how much fuel is left in and kilometers per hour. the fuel tank (when the ignition is in the ON posi- tion). The fuel gauge may vary slightly when the vehicle is in motion or on a grade.
Page 59 Vehicle Controls Table of Contents Page Lights ��59 Autolamp Control ��59 High Beams ��59 Flash-to-Pass ��59 Daytime Running Lamps (DRL) ��59 Dome Lamps ��60 Mirrors ��60 Rearview Mirror ��60 Power Outside Mirrors ��61 Multi-Function Lever ��61 Windshield Wiper ��61 Windshield Washer ��62 Rear Window Washer and Wiper ��62 CRUISE Control ��63 Setting Cruise Control ��63...
Page 60 Table of Contents Page Door and Window Controls��65 Door Locks ��65 Window Operation ��65 Window Lock ��66 Tilt Steering Wheel ��66 Climate Control System ��67 Description of Controls ��67 Vents ��68 Rear Window Defroster Operation ��68 Climate Control System Operating Tips ��69 Rear HVAC ��69 Vehicle Controls...
Page 61: Lights
Pull the multi-function lever towards you slightly to activate and Autolamp Control release to deactivate. Instrument Panel Lighting Dimmer Daytime Running Lamps (DRL) Your MV-1 is equipped with Daytime Running Lamps, which turn on the headlamps with a reduced output under the following conditions: Vehicle Controls...
Page 62: Dome Lamps
MIRRORS • the ignition must be in the RUN position, Rearview Mirror • the headlamp control is in the OFF position, and • the vehicle is in gear. WARNING WARNING Do not adjust the mirror while the vehicle is in motion. Always remember to turn on your headlamps at dusk or during in- REASON: Driving while distracted can result in loss of vehicle...
Page 63: Power Outside Mirrors
Power Outside Mirrors To adjust a mirror, turn the knob left for the driver’s side mirror or right for the passenger’s side mirror then toggle the knob until WARNING the mirror is in the desired position. Once the mirror is adjusted, Do not adjust the mirrors while the vehicle is in motion.
Page 64: Windshield Washer
Windshield Washer CAUTION: Check the washer fluid level frequently. Do not op- erate the wipers when the windshield is dry. Before operating the wiper on a dry windshield, always use the windshield washer. In freezing weather, be sure the wiper blades are not frozen to the windshield before operating the wipers.
Page 65: Cruise Control
CRUISE CONTROL When Cruise Control is active, the Cruise Control Indicator light at the bottom right bank of switches in the center console will With Cruise Control set, you can maintain a set speed without illuminate. keeping your foot on the accelerator pedal. WARNING Do not use the Cruise Control in heavy traffic, traffic that varies in speed, or on roads that are winding, hilly, slippery or unpaved.
Page 66: Disengaging Cruise Control
Disengaging Cruise Control Reducing Speed while using Speed Control There are two ways to reduce a set speed: To disengage the Cruise Control, depress the brake pedal. The Cruise Control Indicator light will go out, indicating the system • Press and hold the SET - control until you get to is not active.
Page 67: Door And Window Controls
DOOR AND WINDOW CONTROLS Window Operation To open any of the windows, push down and hold the switch to Door Locks open the window. To close, pull up on the switch. There is also a window switch on each of the passenger doors. WARNING Before closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the...
Page 68: Window Lock
Window Lock TILT STEERING WHEEL WARNING The window lock feature allows only the driver to operate the power windows from the controls on the driver’s door. NEVER adjust the steering column when the vehicle is moving. REASON: To lock out all the window controls (except for the driver’s) press Driving while distracted can result in loss of vehicle control, accident and serious bodily injury or death�...
Page 69: Climate Control System
CLIMATE CONTROL SYSTEM Air Flow Selections - Controls the direction of the airflow in the vehicle. Description of Controls NOTE: For the best air flow to the rear of the vehicle, use the dash/floor mode. - Distributes air only through the dash vents. - Distributes air through dash and floor vents.
Page 70: Vents
Vents Rear Window Defroster Operation There are three types of vents in your MV-1. The Rear Window Defroster works to clear fog and light ice from the rear window. To use the defroster: Dash Vents - There are four dash vents like the lower vent one shown •...
Page 71: Climate Control System Operating Tips
The recommended maximum cooling settings for driver only are: Climate Control system set to Dash mode with the blower To ensure that your MV-1 Climate Control System operates ef- on high, the A/C set to the coldest temperature setting and Air Re- fectively: circulation on�...
Page 72 WEATHER CONTROL SETTINGS Hot weather and Start the vehicle, select “Dash/Floor” mode then press the A/C and Recirculation buttons. vehicle interior is Set the Fan Speed to the highest setting and set temperature to coldest setting. Roll the win- dows down to flush out hot air. Roll the windows up after hot air is expelled. Adjust the fan very hot and temperature as desired once the vehicle has cooled down.
Page 73 Seating and Safety Restraints Table of Contents Page Seats ��73 Driver’s Seat Controls ��73 Driver’s Seat Features ��74 Jump Seat ��75 Seat Belt Warnings ��76 Seat Belts ��76 Seat Belt Operation and Adjustment ��76 Seat Belt Height Adjuster ��77 Seat Belt Pretensioner ��77 Wearing Seat Belts Properly ��78 Seat Belt Maintenance ��80 Seat Belts For Children ��81...
Page 74 Table of Contents Page Combining Safety Belt and LATCH Lower Anchors for Attaching Child Safety Seats ��84 Wheelchair Restraints ��85 Wheelchair Securing ��86 Wheelchair Retractor Removal ��89 Occupant Restraints ��90 Air Bag Supplement Restraint System (SRS) ��92 Important SRS Precautions ��92 Dual Stage Frontal Air Bag ��92 Side Curtain Driver’s Seat Air Bag ��93 Driver’s Seat Side-Impact Air Bag ��94...
Page 75: Seats
SEATS • Powered Switch - Moves the seat up and down. To move the seat, press the up or down side of the toggle switch until the Driver’s Seat Controls seat is at the desired height. • Fore/Aft Manual Adjustment Handle - Moves the seat for- WARNING ward or back.
Page 76: Driver's Seat Features
Driver’s Seat Features INTEGRATED Your driver’s seat has a DRIVER’S HEAD built-in head restraint in the ARMREST RESTRAINT seat back. There is no need for adjustment as it is inte- grated into the padding of the seatback. STORAGE The seat also comes equipped POUCH with the following features: •...
Page 77: Jump Seat
To stow the jump seat, pull up on the seat base, then slide it back into the stowed position. Your MV-1 may be equipped with the optional jump seat. The jump seat is attached to the floor behind the driver’s seat and faces the rear seats.
Page 78: Seat Belt Warnings
If a seat belt is too short even when fully extended, seat belt ex- See Wearing Seat Belts Properly on page 78 for more detailed tenders can be purchased from your authorized MV-1 service information on Seat Belt usage. center. Seat belt extenders should be used only if the existing belt is not long enough.
Page 79: Seat Belt Height Adjuster
Your MV-1 is equipped with a seat belt pretensioner for the driv- er’s seating position. To set the seat belt height adjuster: The seat belt pretensioner removes some slack from the safety 1.
Page 80: Wearing Seat Belts Properly
Wearing Seat Belts Properly WARNING To help avoid serious personal injury or death, ALL vehicle oc- A seat belt is most effective when worn properly. A seat belt worn cupants must ALWAYS wear properly adjusted seat belts during improperly will not provide the necessary restraining capabilities vehicle operation.
Page 81 WARNING WARNING NEVER use one seat belt for MORE than one person. NEVER wear the shoulder harness strap under the arm. REASON: REASON: The seat belts are designed to help restrain one per- During a collision, the up- son at a time in one seating position� One seat belt does not safely per body could move too far forward, secure more than one occupant in the same seat�...
Page 82: Seat Belt Maintenance
Seat Belt Maintenance WARNING NEVER twist ANY part of a seat belt in ANY way. Periodically inspect all seat belts for any noticeable damage. REASON: Check all attaching hardware for security of mounting. Check all A twisted seat belt will not retractors, latch plates, belt buckles, and release buttons for prop- be able to use its full width to take impact er operation.
Page 83: Seat Belts For Children
Seat Belts For Children Infants and Toddlers Seat belts are not for adults only. Infants, toddlers, and children WARNING smaller than adults need to be properly secured in a seat to ensure ALWAYS SECURE infants and toddlers in an infant or child re- straint.
Page 84 WARNING WARNING ALWAYS SECURE children with seat belts when in the vehicle. NEVER allow a child to wear the safety belt with the belt behind REASON: Children who are not buckled up can be seriously or their backs. fatally injured in an accident, and can collide with other occupants REASON: A child can be seriously in- in the vehicle�...
Page 85: Attaching Child Safety Seats With Latch (Lower Anchors And Tethers For Children) Attachments
Attaching Child Safety Seats with LATCH Ventures recommends the use of a child safety seat having a top (Lower Anchors and Tethers for CHildren) At- tether strap. tachments WARNING NEVER attach two child safety The LATCH system is composed of three anchor points: two low- seats to the same lower anchor er anchors located where the vehicle seat back and seat cushion and/or tether anchor.
Page 86: Combining Safety Belt And Latch Lower Anchors For Attaching Child Safety Seats
The rear seat of your MV-1 is equipped with three built-in tether strap anchors located behind the seats as shown. Attach the tether strap only to the appropriate tether anchor as shown.
Page 87: Wheelchair Restraints
WHEELCHAIR RESTRAINTS The MV-1 is designed and intended for use with wheelchairs that meet or exceed the WC19 wheelchair transit standard developed Your MV-1 may be equipped with the QRT MAX wheelchair by the American National Standards Institute (ANSI ®...
Page 88: Wheelchair Securing
Wheelchair Securing Before securing a wheelchair, make sure that all the parts of the restraint system are in good working order and that the tracks are There are four sets of floor tracks in your vehicle for securing a wheel- free from dirt and debris.
Page 89 4. Rotate the retractors 90 degrees so the securing hooks are aligned Rear with the wheelchair to check that View the retractors are properly spaced. For common wheelchair sizes, the center to center measurement for the rear retractors should be be- tween 13 and 15 inches (330-381 mm).
Page 90 The attachment angle of the rear straps should be between 30 and Repeat for the other side. Once both of the rear tiedown 45 degrees. straps are secured, roll the wheelchair in the desired posi- tion and the retractors will tighten the straps. The wheelchair wheels can then be locked.
Page 91: Wheelchair Retractor Removal
Once the retractors are in the desired position for that 2. Remove one of the wheelchair, pull the belt out and attach the securing hook rear retractors by pull- to a rigid frame member towards the front of the wheel- ing up on the lock re- chair.
Page 92: Occupant Restraints
Occupant Restraints WARNING The lap belt must NEVER pass over or around armrests, side pan- The QRT MAX wheelchair securement system comes equipped els, or other devices that will prevent the belt from lying directly on with a two-piece lap belt and a shoulder belt, all of which can be the body of the passenger.
Page 93 Move to behind the wheelchair and take the piece of the lap belt clos- est to the driver’s side and attach it to the pin connector on the rear retractor on that side. Pull the belt to make sure that the attach- ment plate is completely pulled up on the pin.
Page 94: Air Bag Supplement Restraint
SYSTEM (SRS) Do not attempt to service, repair, or modify the air bag supplemen- tal restraint systems or its fuses. Contact your authorized service Your MV-1 is equipped with center as soon as possible. a driver’s Air Bag Supple- WARNING...
Page 95: Side Curtain Driver's Seat Air Bag
Side Curtain Driver’s Seat Air Bag WARNING National Highway Traffic Safety The Side Curtain Driver’s Seat Air Bag is designed to deploy Administration (NHTSA) recom- during significant side crashes. The air bag is located above the mends a minimum distance of at trim panels of the driver’s side front window.
Page 96: Driver's Seat Side-Impact Air Bag
Driver’s Seat Side-Impact Air Bag WARNING The Driver’s Seat Side-Impact Air Bag is designed to deploy in Do not attempt to service, repair or modify the Driver’s Seat Side- Impact Air Bag, its fuses, or the seat cover. You could be seriously side crashes that affect the driver’s side of the vehicle.
Page 97: Determining If The System Is Operational
are otherwise out of position at the time of air bag deployment. WARNING It is extremely important that occupants be properly restrained as Do not touch the air bag system components after inflation. far away from the air bag module as possible while maintaining REASON: Several air bag system components get hot after vehicle control.
Page 98: Disposal Of Air Bags And Air Bag Equipped Vehicles (Including Pretensioners)
paired. If any of these things happen, even intermittently, EVENT DATA RECORDER contact your authorized service center as soon as possible. This vehicle is equipped with an event data recorder (EDR). The main Unless serviced, the system may not function properly in the purpose of an EDR is to record, in certain crash or near crash-like sit- event of a collision.
Page 99 Driving Table of Contents Page Driving Responsibly ��99 Staying Focused ��99 Using Safety Restraints ��99 Passenger Safety ��99 Cargo ��99 Starting the Vehicle��100 Ignition Positions ��100 Preparing to Start Your Vehicle ��100 Before Starting the Vehicle ��101 Starting the Engine ��101 Engine Block Heater ��102 Exhaust Fumes��103 Automatic Transmission Operation��104...
Page 100 Table of Contents Page Tow/Haul (T/H) ��107 Brakes ��108 Four-Wheel Anti-Lock Brake System (ABS) ��108 Parking Brake ��109 Traction Control �� 110 Electronic Stability Control�� 111 Driving in Adverse Conditions�� 111 Driving in Rain and on Wet Roads �� 111 Driving Through Water ��...
Page 101: Driving Responsibly
DRIVING RESPONSIBLY WARNING NEVER leave children, adults who normally require the assistance Staying Focused of others, or pets in the vehicle in hot weather. REASON: The temperature inside the vehicle can rise quickly, As the driver, you are responsible for keeping yourself, your pas- which could lead to serious bodily harm or death�...
Page 102: Starting The Vehicle
STARTING THE VEHICLE Preparing to Start Your Vehicle When starting a fuel-injected engine, don’t press the accelerator Ignition Positions before or during starting. For more information on starting the vehicle, refer to Starting the Engine on page 101. OFF - locks the automatic WARNING transmission gearshift lever and allows key removal.
Page 103: Before Starting The Vehicle
Before Starting the Vehicle When the engine starts, the idle RPM runs slightly faster to warm the engine. If the engine idle speed does not slow down automati- Make sure all occupants buckle their safety belts. For more cally, have the vehicle inspected. information on safety belts and their proper usage, refer to the After idling for a few seconds, apply the brake, shift into gear Seating and Safety Restraints chapter starting on page 71.
Page 104: Engine Block Heater
Your vehicle may be equipped with a dealer-installed engine REASON: block heater to aid in starting your MV-1 in very cold weather. To Damage to the block heater cord may result� use the engine block heater, simply plug the heater in at least two hours before starting the vehicle if temperatures are between 0 and -10 F (-18 and -23 C).
Page 105: Exhaust Fumes
EXHAUST FUMES THE BEST DEFENSE AGAINST EXHAUST POISONING IS ADEQUATE VENTILATION. WARNING Take the following precautions to avoid exposure to exhaust Engine exhaust and a wide variety of automobile components and fumes: parts, including components found in the interior furnishings in a vehicle, contain or emit chemicals known to the State of California •...
Page 106: Automatic Transmission Operation
AUTOMATIC TRANSMISSION OPERATION Adaptive Transmission Shift Strategy Your vehicle’s automatic transmission is equipped with a special Your vehicle is equipped with an Adaptive Transmission Shift shift strategy that ensures maximum heater performance during Strategy. Adaptive Transmission Shift Strategy offers the optimal cold weather operation.
Page 107: Gearshift Lever
Gearshift Lever Gearshift Positions Park (P) Your automatic transmission gear shift lever is on the right side of the steering column. This position locks the transmission and prevents the rear wheels from turning. The vehicle cannot be shifted out of Park if the right rear door is open.
Page 108 Manual (M) WARNING With the transmission gear shift lever in Manual mode: Do not hold the + or - buttons in on the gear shift lever. REASON: • the transmission provides maximum engine braking. This may damage the transmission which could lead to an accident or injury�...
Page 109: Progressive Range Selection (Prs)
Progressive Range Selection (PRS) Tow/Haul (T/H) Progressive Range Selection gives you the ability to lockout gear Tow/Haul delays transmission upshift to reduce the frequency of from the automatic shifting range. This may provide you with an transmission shifting. The system provides engine braking in all improved driving performance in certain situations such as driv- forward gears when the gearshift lever is in D (Drive).
Page 110: Brakes
BRAKES Using ABS WARNING When hard braking is required, apply continuous force on the brake pedal. The ABS will be activated automatically, allowing Braking and/or steering functions can be affected in the event of a you to retain steering during hard braking and on slippery sur- engine cutoff while driving.
Page 111: Parking Brake
Even when the ABS is disabled, normal braking is still effective. If the Brake System Warning Light illumi- nates with the parking brake released, however, have your brake system serviced immediately by an authorized service center. Parking Brake To set the parking brake (1) press the parking brake pedal down until the pedal stops.
Page 112: Traction Control
TRACTION CONTROL trol OFF button at the top right in bank of switches in the center console. A Traction Control OFF indicator light located in the Your vehicle is equipped with a Traction Control system. This instrument cluster will illuminate steadily while the system is off. system helps you maintain the stability and steering ability of your vehicle, especially on slippery road surfaces such as snow or ice-covered roads and gravel roads.
Page 113: Electronic Stability Control
ELECTRONIC STABILITY CONTROL DRIVING IN ADVERSE CONDITIONS Road conditions can change quickly due to the weather. It is im- Electronic stability control (ESC) may enhance your vehicle’s di- rectional stability during adverse maneuvers, for example when portant to adjust your driving to the road conditions and always cornering severely or avoiding objects in the roadway.
Page 114: Driving Through Water
Winter Driving Driving Through Standing Water You should always be prepared for deteriorating road conditions during the winter. Make sure your MV-1 is ready for winter driv- CAUTION: If you drive too quickly through deep puddles or ing. Tires, brakes and wipers should all be in good working order.
Page 115 Before running the engine for warmth, clear snow away from sudden steering maneuvers. around the base of your MV-1 because snow can trap exhaust gases underneath the vehicle. This condition could allow exhaust to enter the vehicle.
Page 116 • Periodically check to make sure snow is not collecting around the base of the vehicle. See page 103 for exhaust warnings. • Open the window about two inches (5 cm) on the side of the vehicle that is not facing the wind to bring fresh air into the vehicle.
Page 117 Liftgate/Power Swing Door/Ramp Table of Contents Page Multi-Function Fob �� 117 Replacing the Battery �� 117 Replacing or Adding Multi-Function Fobs �� 118 Reprogramming Multi-Function Fobs �� 118 Liftgate �� 119 Manual Liftgate �� 119 Power Liftgate ��120 Power Swing Door ��121 Opening/Closing ��121 Emergency Unlock Handle ��122 Wheelchair Loading ��123...
Page 118 Table of Contents Page Ramp Retraction/Deployment - Mechanical Override ��130 Ramp OFF Switch ��132 Power Ramp Maintenance ��133 Manual Ramp ��134 Ramp Deployment ��134 Ramp Stowage ��135 Liftgate/Power Swing Door/Ramp...
Page 119: Multi-Function Fob
MULTI-FUNCTION FOB CAUTION: DO NOT take the circuit board off the front housing of the remote entry transmitter. Your vehicle may come equipped with two Multi-Function Fobs. REASON: The Fobs have buttons for the Liftgate, Power Ramp and Power Removing the circuit board could cause the transmit- ter to fail�...
Page 120: Replacing Or Adding Multi-Function Fobs
Replacing or Adding Multi-Function Fobs Press and hold the button labeled “PROGRAM” on the re- ceiver until the red LED in the program button illuminates If you would like to have your Multi-Function Fob reprogrammed (approximately 5 seconds). The receiver is now in the trans- because you lost one, or would like to buy additional fobs, you mitter program mode.
Page 121: Liftgate
LIFTGATE Manual Liftgate WARNING The liftgate is locked and un- locked by the master door lock AVOID driving with the liftgate open. switch on the driver’s door panel REASON: Passengers and cargo are at risk of falling out of the or by pressing the button on vehicle and driving with the liftgate open can cause damage to...
Page 122: Power Liftgate
Power Liftgate WARNING Your vehicle may be equipped with a Power Liftgate. To open the Keep the Multi-function Fob out of the reach of children and do not Power Liftgate: allow them to play near an open or moving Power Liftgate. REASON: •...
Page 123: Power Swing Door
POWER SWING DOOR Opening/Closing Your vehicle may be equipped with a rear right side Power Swing The switches for the Power Swing Door are located: Door. The Power Swing Door can be operated by your key fob • on the edge of the door, and or by the power door switches.
Page 124: Emergency Unlock Handle
Your vehicle also comes equipped Power WARNING with a Multi-fuction Fob that can Swing Keep the Multi-function Fob out of the reach of children and do Door also open and close the door. not allow them to play near an open or moving Power Swing Door. Button REASON: To open or close the Power Swing...
Page 125: Wheelchair Loading
Wheelchair Loading To unlock the door, pull the Emergency Unlock Handle up then towards you. The door can then be opened from the inside using Passengers in wheelchairs should always go up and down the the indside door handle. ramp facing forward. Assistance is strongly recommended during NOTE: a long Ramp deploy (both manual and power) and is necessary The Power Swing Door cannot be opened from the out-...
Page 126: Power Ramp
• Long Deployment - A more gradual 1:6 ratio slope where the ramp fully telescopes to 92.25 in (2343 mm), not including Your MV-1 may be equipped with a 30 in (762 mm) wide power space to maneuver. ramp that can be deployed to various heights and terrain condi- NOTE: tions.
Page 127: Ramp Deployment
Ramp Deployment This warning sticker, affixed to the door next to the ramp switch- es, outlines the safety procedures you should follow while using • Place the vehicle in PARK. the power ramp. NOTE: The ramp will not function if the vehicle is not in park� NOTE: The ramp will not function if the vehicle is running and the Ramp OFF switch, located in the center switch bank under the...
Page 128 Long The switches for the Power Ramp are located: Your vehicle may also come equipped Deploy with the Multi-Function Fob shown • on the edge of the right rear door, and on the right that can also be used to deploy and retract the ramp.
Page 129 • Near the end of ramp deployment, fences will swing up on • The ramp is fully deployed when the ramp is secured against both sides of the ramp to help prevent wheelchair run-off. the threshold and the cams are locked as shown below. There will be a two second tone at the end of the deploy cycle.
Page 130: Obstacle Detection Feature
Ramp Switches. Either retract the ramp manually by following the procedure in Ramp Retraction/ Deployment - Mechanical Override on page 130 or have the vehicle towed to an authorized MV-1 Service Center. 10-WOM3-059 Liftgate/Power Swing Door/Ramp...
Page 131: Ramp Retraction
Ramp Retraction CAUTION: Do not continue to press the Ramp Switches or fob buttons when the ramp is not working. WARNING REASON: Continuing to press the Ramp Switches or fob but- NEVER attempt to retract the ramp while an occupant is still on tons when the ramp is not working could cause damage to the the ramp.
Page 132: Ramp Retraction/Deployment - Mechanical
The audible chime will switch off when the ramp is fully the mechanical override procedure below and have the system retracted. checked at an authorized MV-1 Service Center. • If the ramp will not retract fully, re-deploy it and check for To retract or deploy the ramp:...
Page 133 Insert the T-handle tool with the extender and included sock- et on the drive sprocket. Begin to retract the ramp by turning the T-handle with a clockwise rotation. If you are deploying the ramp, turn the T-handle counterclockwise. NOTE: Grip the outermost edges of the tool for best leverage� NOTE: Having another person manually lift the end of the ramp 6 to 12 inches off the ground during the retraction process will...
Page 134: Ramp Off Switch
Reinstall the floor cover. Ramp OFF Switch NOTE: Control of the ramp switches on the door, the B-Pillar inside The ramp will operate slowly the first time retracting after the vehicle and fob can be disabled from inside the vehicle. The a mechanical override until the system locates its “home”...
Page 135: Power Ramp Maintenance
Power Ramp Maintenance To clear a valve, simply squeeze it open to expel the dust or road salt. The valve will automatically close after it is released. Your Power Ramp does not need regular maintenance to operate To clean the ramp fences, deploy the ramp fully so the fences are properly if you are keeping the ramp free of debris, dirt and ex- up.
Page 136: Manual Ramp
MANUAL RAMP To pull out the manual ramp: WARNING Hold down the storage latch on the left side of the ramp. Check to make sure path for the ramp deployment is clear of peo- ple and objects. REASON: Damage to the ramp and/or serious personal injury could occur�...
Page 137: Ramp Stowage
Pull the ramp out by the loops until it locks into place. 3. Lower the ramp to the ground. NOTE: When the ramp is locked into place, there will be a slight gap between the ramp and threshold� Ramp Stowage NOTE: An audible chime will sound five times if shifting out of park is attempted while the ramp is deployed or the right rear door...
Page 138 Lift the ramp by the loops high enough to release the latches, approximately 15 degrees above level. This will cause the rollers on the ramp to start to drop down in the track and release the cam locks and allow the ramp to retract. WARNING Always use the loops to pull the ramp out and keep hands away from the rollers and the opening.
Page 139: Roadside Emergencies
Roadside Emergencies Table of Contents Page Hazard Flasher Control ��139 Fuel Pump Shut-off ��139 Engine Overheating ��140 Flat Tires ��141 Tire Pressure Monitoring System (TPMS) ��141 Changing Tires with TPMS ��142 Understanding Your Tire Pressure Monitoring System (TPMS) ��142 Jump Starting ��145 Preparing Your Vehicle ��145 Connecting the Jumper Cables ��146 Starting the Vehicle ��147...
Page 140 Table of Contents Page Fuses ��151 Standard Fuse Amperage Rating and Color ��152 Body Control Module ��153 Battery Junction Box ��155 Auxiliary Junction Box ��159 Roadside Emergencies...
Page 141: Hazard Flasher Control
HAZARD FLASHER CONTROL FUEL PUMP SHUT-OFF Your MV-1 is equipped with a hazard flasher control for In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of use if your vehicle is disabled and creating a safety haz- ard for other motorists.
Page 142: Engine Overheating
10 minutes, pull over as soon as safely possible and park the vehicle. You should also park your MV-1 if you see steam or coolant escaping from the coolant system. Shut off the engine and get away from the vehicle. DO NOT open the hood. Have the vehicle towed to a service center.
Page 143: Flat Tires
FLAT TIRES TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recom- Your vehicle has also been equipped with a Low Tire warning mended by the vehicle manufacturer on the vehicle placard or light to indicate when the TPMS system is not operating prop- Tire and Loading Information label.
Page 144: Changing Tires With Tpms
The tire pressure should be checked periodically (at least month- WARNING ly) using an accurate tire gauge. Tire pressures are posted on the Make sure to check your tire pressure on a regular basis. Tire and Loading Information label shown below. The tire label REASON: The Tire Pressure Monitoring System is NOT a is located on the edge of the driver’s door.
Page 145 When You Believe Your System is not Operating Properly The main function of the Tire Pressure Monitoring System is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended. Please refer to the following chart for information concerning your Tire Pressure Monitoring System: LOW TIRE PRESSURE POSSIBLE CAUSE...
Page 146 CAUTION: Before installing a new tire, all of the sealant must be removed from the tire/wheel assembly. Your MV-1 may also come equipped with a tire inflation kit locat- REASON: Failure to remove all of the sealant can cause the ed on the driver’s side in the rear of your vehicle.
Page 147: Jump Starting
JUMP STARTING Preparing Your Vehicle WARNING 1. Use only a 12-volt supply to start your vehicle. Never smoke or have open flames near the battery. 2. Do not disconnect the battery of the disabled vehicle as this REASON: Open flames, sparks, or a lit cigarette can cause could damage the vehicle’s electrical system.
Page 148: Connecting The Jumper Cables
Connecting the Jumper Cables Connect the negative ( - ) cable to the negative ( - ) terminal of the assisting battery. NOTE: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery� Connect the positive ( + ) jumper cable to the positive ( + ) terminal of the discharged battery.
Page 149: Starting The Vehicle
1. Remove the jumper cable from the ground metal surface. WARNING Do not connect the end of the second cable to the negative ( - ) terminal of the battery to be jumped. REASON: A spark may cause an explosion of the gases that surround the battery�...
Page 150: Wrecker Towing
It is acceptable to tow your vehicle with the front wheels on the ground (without dollies) and the rear wheels off the ground. If you need to have your MV-1 towed, contact a professional tow- WARNING ing service, or if you are a member of a roadside assistance pro- gram, your roadside assistance provider.
Page 151: Brake Shift Interlock Override
BRAKE SHIFT INTERLOCK OVERRIDE 3. Turn the steering wheel one-half turn to access the slots on each side of the steering column shroud. If the selector lever cannot be moved out of the PARK position when the ignition is in the ON position and the brake pedal is applied: Apply the park brake and turn the ignition switch to the OFF position.
Page 152 Insert a suitable tool into each slot to unsnap and remove the Turn the ignition switch to the ON position. Pull back on the steering column upper shroud. Rotate the upper shroud on brake shift interlock plunger, apply the brake and shift the its hinges and pull rearward to remove the shroud from its transmission into neutral.
Page 153: Fuses And Relays
FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. CAUTION: Always replace a fuse with one that has the same specified amperage rating.
Page 154: Standard Fuse Amperage Rating And Color
Standard Fuse Amperage Rating and Color COLOR FUSE MINI STANDARD MAXI CARTRIDGE MAXI FUSE LINK RATING FUSES FUSES FUSES FUSES CARTRIDGE Grey Grey Violet Violet Pink Pink 7.5A Brown Brown Blue Blue Yellow Yellow Yellow Blue Blue Natural Natural Green Green Green Pink...
Page 155: Body Control Module
Body Control Module The fuse block, as shown below, is numbered. The numbers cor- respond to the numbers in the circuit chart on the next page. The Body Control Module is located inside the vehicle beneath the center console. To remove the outer cover, pull straight up and out on the handle.
Page 156 BODY CONTROL MODULE BODY CONTROL MODULE FUSE/RELAY FUSE AMP PROTECTED FUSE/RELAY FUSE AMP PROTECTED LOCATION RATING CIRCUITS LOCATION RATING CIRCUITS Central/Configurable Locking 2 Radio CD Nav Supply Central/Configurable Locking 2 7.5A HEC EATC Supply Ignition Swtich Supply LSM SWM Supply ICP MFD Supply PAM Supply IGN PATS Supply...
Page 157: Battery Junction Box
Battery Junction Box The Battery Junction Box is located in the engine compartment. It contains high-current fuses that protect your vehicle’s main electrical systems from overloads. 15-WOM08-004 Battery Junction Box 13-WOM9-005 Roadside Emergencies 155...
Page 158 BATTERY JUNCTION BOX BATTERY JUNCTION BOX FUSE/RELAY FUSE AMP PROTECTED FUSE/RELAY FUSE AMP PROTECTED LOCATION RATING CIRCUITS LOCATION RATING CIRCUITS HC Micro 40A** Engine Cooling Fan #1 Relay 30A** Starter Solenoid Relay HC Micro Starter Solenoid 40A** Run Start Relay Relay 40A** Engine Cooling Fan #2...
Page 159 BATTERY JUNCTION BOX BATTERY JUNCTION BOX FUSE/RELAY FUSE AMP PROTECTED FUSE/RELAY FUSE AMP PROTECTED LOCATION RATING CIRCUITS LOCATION RATING CIRCUITS 15A* Rear HVAC Blower 20A* ABS Logic Battery 15A* Back Up Lamp 20A* Fuel Pump 10A* A/C Clutch 10A* Front Wiper Relay Coil 10A* Stoplamp Sw 25A*...
Page 160 BATTERY JUNCTION BOX BATTERY JUNCTION BOX FUSE/RELAY FUSE AMP PROTECTED FUSE/RELAY FUSE AMP PROTECTED LOCATION RATING CIRCUITS LOCATION RATING CIRCUITS – Not Used 30A** Power Seat – Not Used 20A* VPWR 1 PCM PWR (Secondary) Mini Diode Start 20A* VPWR 2 PC Mil –...
Page 161: Auxiliary Junction Box
Auxiliary Junction Box The Auxiliary Junction Box is located behind the knee panel and above the Parking Brake. The Auxiliary Junction Box consists of six fuses and three relays. AUXILIARY JUNCTION BOX FUSES FUSE/RELAY FUSE AMP PROTECTED LOCATION RATING CIRCUITS HVAC Ramp ABC/Headlamp Switch...
Page 162: Circuit Breakers
Circuit Breakers There are also three automatically-resetting circuit breakers (not shown) for the Power Swing Door, Power Windows and ABC Module (Power Ramp). Take your vehicle to an Authorized Ser- vice Center if there is a loss of power to any of those features. Roadside Emergencies...
Page 163 Maintenance Table of Contents Page Maintenance Schedule And Record Log ��165 Get the Most from Your Vehicle with Routine Maintenance ��165 Protect Your Warranty! ��165 Keeping Maintenance Records is Easy With the Maintenance Schedule ��165 Maintenance Intervals ��166 Choosing a Maintenance Schedule to Follow ��166 Oils, Fluids and Flushing ��166 Chemicals and Additives ��166 Owner Checks and Services ��167...
Page 164 Table of Contents Page Table of Contents Page Maintenance Schedule for Special Use Gasoline Fuel System ��209 “Commercial Fleet” Driving Conditions ��183 Fuel Filter ��209 Hood ��203 Important Safety Precautions ��209 Raising ��203 Refueling ��210 Lowering ��204 Fuel Filler Cap �� 211 Wheels and Tires ��205 Choosing the Right Fuel ��212 Inspection and Care ��205...
Page 165 Table of Contents Page Table of Contents Page Engine Coolant ��219 Interior ��229 Technical Specifications ��230 Checking Engine Coolant ��219 Adding Engine Coolant ��220 Capacities ��230 Transmission Fluid ��222 Engine Data ��231 Brake Fluid ��222 Drivebelt Routing ��232 Power Steering Fluid ��223 Cooling System Data ��232 Battery ��224 Transmission Data ��232...
Page 167: Maintenance Schedule And Record Log
Mobility Ventures from your MV-1. This is exactly why we put together the Main- engineering specifications. Failure to perform scheduled main- tenance Schedule. It outlines the services required to properly tenance specified in this guide may invalidate warranty coverage maintain your vehicle and when they should be performed.
Page 168: Maintenance Intervals
It is easy to determine which maintenance schedule you should use. Use the normal schedule if you drive your vehicle under ev- Non- MV-1 approved chemicals or additives are not required for eryday conditions. If, however, one or more of the special operat- factory recommended maintenance.
Page 169: Owner Checks And Services
Owner Checks and Services Check Every Six Months for All Vehicles It is recommended that the following basic maintenance checks and Check lap/shoulder belts and seat latches for wear and proper operation� inspections be performed at the designated time intervals. Check Check power steering fluid level.
Page 170: Tires
Tires Additionally, the use of non-recommended tires and wheels could cause steering, suspension, axle or transfer case/power transfer Proper tire maintenance and replacement are critical to your ve- unit failure. If you have questions regarding tire replacement, see hicle’s performance and helps keep you and your passengers safe. an authorized service center.
Page 171: Collision
Inspect half shaft dust boots, if equipped� Multi-Point Inspection Check shocks and struts and other suspension components for To keep your MV-1 running properly, it is important to have the leaks and damage� systems on your vehicle checked regularly. This can help identify Inspect steering and linkage�...
Page 172: Maintenance Schedule For Normal
Maintenance Schedule for Normal “Non-Commercial” Driving Conditions 7,500 miles/12,000 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Replace differential fluid. Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag�...
Page 173 22,500 miles/ 36,200 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Inspect engine air filter.
Page 174 37,500 miles/ 60,330 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 175 52,500 miles/ 84,500 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Replace differential fluid. Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag�...
Page 176 67,500 miles/ 108,600 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 177 82,500 miles/ 132,700 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 178 97,500 miles/156,900 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 179 112,500 miles/181,000 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 180 127,500 miles/205,100 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 181 142,500 miles/229,300 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 182 157,500 miles/253,400 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 183 172,500 miles/277,600 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 184 187,500 miles/301,700 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 185 Maintenance Schedule for Special Use “Commercial Fleet” Driving Conditions 5,000 miles/8,000 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Replace differential fluid. Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag�...
Page 186 15,000 miles/ 24,100 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 187 25,000 miles/ 40,200 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 188 35,000 miles/ 56,300 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 189 45,000 miles/ 72,400 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 190 55,000 miles/ 88,500 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 191 65,000 miles/104,600 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 192 75,000 miles/120,700 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 193 85,000 miles/136,800 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 194 100,000 miles/160,900 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Replace differential fluid. Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag�...
Page 195 110,000 miles/177,000 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 196 120,000 miles/193,000 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 197 130,000 miles/209,200 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 198 140,000 miles/225,270 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 199 150,000 miles/241,400 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Replace differential fluid. Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag�...
Page 200 160,000 miles/257,400 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 201 170,000 miles/273,500 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 202 180,000 miles/289,600 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 203 190,000 miles/305,700 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag� Lube all body hinges�...
Page 204 200,000 miles/321,800 kilometers Change engine oil and replace oil filter. Service Center: Rotate tires, inspect tires for wear and measure tread depth� Replace differential fluid. Inspect ramp operation and check tracks and side fences for debris and clean as necessary� Inspect the wheels and related components for abnormal noise, wear, looseness or drag�...
Page 205 HOOD 3. Lift the hood and secure it with the prop rod. Raising Pull the hood release latch located under the bottom left cor- ner of the instrument panel towards you. Go to the front of the vehicle and pull up slightly on the hood to access the safety latch.
Page 206 Lowering Slightly lift the hood. Remove the prop rod and stow in the proper location. Close the hood, making sure that it latches. WARNING The hood must be completely closed and latched before driving. REASON: The hood could open while driving, obscuring your vision and causing a collision which could result in serious bodily injury or death�...
Page 207 WHEELS AND TIRES Damage Uneven wear, gouges, cracks, cuts, bulges, or any exposed body Inspection and Care ply cords indicates tire damage that should be addressed imme- diately. Tires will wear more quickly when they are kept at im- Frequent inspection of the tires will prevent tire failure and pos- proper tire pressures or when wheels are not aligned properly.
Page 208 • Remove the tire chains when they are no longer needed. Do WARNING not use tire chains on dry roads. When selecting snow tires for your MV-1, ensure that the tires are WARNING the same size, load index and speed rating as those originally pro- vided with the vehicle.
Page 209 INFORMATION ABOUT UNIFORM TIRE would wear one and one-half (1 1/2) times as well on the govern- QUALITY GRADING ment course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, Tire Quality Grades apply to new pneumatic passenger car tires.
Page 210: Tire Rotation
Front of Vehicle on the laboratory test wheel than the minimum required by law. The temperature grade established for the MV-1 tire is for a tire Lug Nut Tightening Order that is properly inflated and not overinflated. Excessive speed, under-inflation, or excessive loading, either separately or in com- bination, can cause heat buildup and possible tire failure.
Page 211: Fuel Filter
GASOLINE FUEL SYSTEM Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before Fuel Filter fueling your vehicle. Your vehicle filter is equipped with a lifetime fuel filter that is in- • Always turn off the vehicle before fueling. tegrated with the fuel tank.
Page 212 Refueling • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breath- WARNING ing gasoline and/or ethanol vapors, or skin contact could Fuel vapor burns violently and a fuel fire can cause severe injuries. cause an adverse reaction.
Page 213: Fuel Filler Cap
Fuel Filler Cap 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/4 of a turn until it clicks at least once.
Page 214 Choosing the Right Fuel Octane Recommendations Your vehicle is NOT a flexible fuel vehicle (FFV). Only use UN- Your vehicle is designed to use “Regular” unleaded gasoline with LEADED fuel or UNLEADED fuel blended with a maximum of a pump (R+M)/2 octane rating of 87. Some stations offer fuels 10% ethanol.
Page 215: Running Out Of Fuel
Running Out of Fuel Avoid running out of fuel. This situation may have an adverse effect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine.
Page 216: Filling The Tank
ESSENTIALS OF GOOD FUEL ECONOMY able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. Measuring Techniques For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the OFF position prior to Your best source of information about actual fuel economy is refueling.
Page 217: Calculating Fuel Economy
Calculating Fuel Economy EPA Fuel Economy Estimates Fill the fuel tank completely and record the initial odometer Every new vehicle should have a sticker on the window called the reading (in miles or kilometers). Monroney Label which contains EPA fuel economy estimates. Contact your authorized service center if the Monroney label is Each time you fill the tank, record the amount of fuel added not supplied with your vehicle.
Page 218: Engine Oil
ENGINE OIL • Oil levels above the upper hole or the MAX mark may cause engine damage. Some oil must be removed from the Checking the Engine Oil engine by an authorized service center. Refer to the Maintenance Schedule at the beginning of this sec- tion for the appropriate intervals for checking the engine oil.
Page 219: Adding Engine Oil
Adding Engine Oil 2. Recheck the engine oil level. Make sure the oil level is not above the normal operating range on the engine oil level If the engine oil level is not within the normal range, add dipstick. only certified engine oil of the recommended viscosity. Re- 3.
Page 220 Engine Oil and Filter Recommendations prised of U.S. and Japanese automobile manufacturers. Look for this certification trademark. To protect your engine and the engine’s warranty, use SAE 5W- 20 Premium Synthetic Blend Motor Oil. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Page 221: Engine Coolant ��219 Interior
ENGINE COOLANT When the engine is cold, check the level of the engine coolant in the reservoir. Checking Engine Coolant The concentration and level of engine coolant should be checked at the intervals listed in Maintenance Schedule at the beginning of this section.
Page 222: Adding Engine Coolant
If the engine coolant has not been checked at the recommended ® Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37- interval, the engine coolant reservoir may become low or empty. If the reservoir is low or empty, add engine coolant to the reser- ®...
Page 223 After any coolant has been added, check the coolant concentra- WARNING tion. Refer to Checking Engine Coolant on page 219. If the con- MAKE SURE the engine is cool before unscrewing the coolant centration is not 50/50 (protection to –34°F/–36°C), drain some pressure relief cap.
Page 224: Transmission Fluid
TRANSMISSION FLUID BRAKE FLUID Your transmission does not consume fluid. The fluid level should The fluid level will drop slowly as the brakes wear, and will rise be checked at an authorized service center, however, if the trans- when the brake components are replaced. Fluid levels between the “MIN”...
Page 225: Power Steering Fluid
POWER STEERING FLUID 2. If the fluid level is low, start the engine. Check the fluid level when it is at ambient temperature, 20° – 80° 3. While the engine idles, turn the steering wheel left and right several times. F (-7°...
Page 226: Battery
WARNING When working near the battery, ALWAYS shield your face and pro- Your MV-1 is equipped with a Group 65 750 cold-cranking amp tect your eyes. Always provide proper ventilation and do not allow maintenance-free battery which normally does not require addi- flames, sparks or lighted substances to come near the battery.
Page 227: Relearn After Battery Replacement ��225 Vehicle Dimensions
7. Drive the vehicle to complete the relearning process. WARNING • The vehicle may need to be driven 10 miles (16 km) or ALWAYS wash hands after handling a battery. more to relearn the idle and fuel trim strategy REASON: Battery posts, terminals and related accessories •...
Page 228: Windshield Washer Fluid
WINDSHIELD WASHER FLUID WIPER BLADES Add fluid to fill the reservoir if the level is low. The capacity of Pull the wiper arm away from the vehicle. Turn the blade at the reservoir is 1.0 gal (3.8 L). In very cold weather, do not fill the an angle from the wiper arm.
Page 229: Floor Mats
FLOOR MATS Replace wiper blades at least once per year for optimum perfor- mance. Poor wiper quality can be improved by cleaning the wiper Your vehicle may be equipped with driver’s side floor mats that blades and the windshield. Refer to Windows and Wiper Blades are secured to the floor with hooks.
Page 230: Cleaning Instructions
CLEANING INSTRUCTIONS Wax your vehicle’s body panels as necessary. Frequent waxing will remove deposits from the vehicle’s surface and protect the WARNING vehicle’s finish. The undercarriage should be hosed off occasion- ALWAYS follow the manufacturer’s instructions AND allow proper ally to remove any dirt and road salt build-up. ventilation when using cleaning products.
Page 231: Windows And Wiper Blades
Windows and Wiper Blades wiper blades using a sponge or soft cloth with a neutral de- tergent or mild-abrasive cleaning solution. After cleaning, The windshield, rear and side windows and the wiper blades rinse the windshield and wiper blades with clean water. The should be cleaned regularly.
Page 232: Capacities
TECHNICAL SPECIFICATIONS Capacities CAPACITY DESCRIPTION RECOMMENDED BRAND AND/OR FILL TYPE Standard Metric Fuel Tank 24 gal 90.8 L 87 Octane Gasoline Engine 6.0 qt 5.7 L Motorcraft® SAE 5W-20 Premium Synthetic Blend Motor Oil (crankcase with new filter) (U.S); SAE 5W-20 Super Premium Motor Oil (Canada) Cooling System 17.4qt 16.4 L...
Page 233: Engine Data
ENGINE DATA Type: Ford® 3.7L V6 Horsepower (net rating): 275 hp @ 6000 rpm Torque: 260 ft-lb @ 4000 rpm Governor Type: Electronic 3.7L (4V) (226 CID) Displacement: Bore/Stroke: 95.5. /86.7 mm (3.759/3.413 in) Compression Ratio: 10.5:1 Oil Type: SAE 5W-20 Premium Synthetic Blend (U.S.) SAE 5W-20 Super Premium Motor Oil (Canada) Oil Pressure @1,500 rpm with engine at Normal Operating Temperature: 30.0 psi (206.8 kPa)
Page 234: Cooling System Data
Drivebelt Routing COOLING SYSTEM DATA 3.7L V6 Engine Cap Pressure: 16 psi Thermostat: 188°F (86.6°C) Radiator: 2 Core Fan: Electric Normal Operating Coolant 205°F (96.1°C) Temperature: TRANSMISSION DATA ® Model: Ford 6R80 Type: Automatic with 6 Forward Speeds and Overdrive ®...
Page 235 VEHICLE DIMENSIONS LENGTH ANGLE EXTENSION 13-WOM10-013 Wheelbase: — 122.0 in 3099 mm Length — 205.0 in 5207 mm Height: — 76.3 in* 1938 mm* Width: — 79.4 in 2017 mm Footprint: — 57.9 ft2 5.38 m2 Frontal Area: — 37.77 ft2 3.51 m2 Turning Circle (curb to curb): —...
Page 236 Interior Height at Forward Wheelchair Position: 58.3 in 1481 mm Overall Interior Floor Length: 81.5 in 2070 mm Interior Width at B-Pillars: 64.5 in 1638 mm Vehicle Ground Clearance (minimum): 6 in* 152 mm* Ramp Length - Short Deployment (Manual): 63.75 in 1619 mm Ramp Length - Short Deployment (Power):...
Page 237 Hip Room: Front/Rear 63/69 in 1600/1761 mm Leg Room: Front/Rear 42.1/36.6 in 1070/931 mm Shoulder Room: Front/Rear 65.3/66.9 in 1658/1700 mm Cargo Volume Index: 36.4 ft3 1031 L Curb Weight: 5,055 lbs 2293 kg Payload: 1,545 lbs 700.80 kg Gross Vehicle Weight Rating (GVWR): 6,600 lbs 2994 kg Gross Axle Weight Rating (GAWR Front):...
Page 238: Metric/U�S� Equivalents
METRIC/U.S. EQUIVALENTS Multiply To Get Multiply To Get Inches Inches 2.54 Centimeters Centimeters 0.394 Feet 0.305 Meters Meters 3.280 Feet Miles 1.609 Kilometers Kilometers 0.621 Miles Square Inches Square Inches 6.451 Square Centimeters Square Centimeters 0.155 Cubic Inches Cubic Inches 16.39 Cubic Centimeters Cubic Centimeters...
Page 239 Index...
Page 240 Relearn After Battery Replacement ....... 225 Warranty Coverage ............3 Air Bag Supplement Restraint System (SRS) Brakes Determining if the System is Operational ......95 Fluid ................222 Disposal of Air Bags and Air Bag Equipped Vehicles (in- Four-Wheel Anti-Lock Brake System (ABS) ....108 cluding pretensioners) ..........
Page 241 Windows and Wiper Blades ........... 229 Through Water ............112 Climate Control System Winter Driving ............112 Description of Controls ............ 67 Responsibly ..............99 Operating Tips ..............69 Traction Control ............. 110 Rear HVAC ..............69 Rear Window Defroster Operation ........68 Vents .................
Page 242 Federal Highway Administration Regulation ......29 Gauges Floor Mats ................227 Engine Coolant Temperature ........... 54 Fuel Economy Fuel .................. 55 Calculating Fuel Economy ..........215 Odometer ................55 EPA Fuel Economy Estimates ........215 Speedometer ..............55 Filling the Tank .............. 214 Tachometer ...............
Page 243 Hazard Flasher Control ............139 Labels Emission Control Information ......... 27 Hood Lowering ................ 204 Warning ................24 Raising ................203 Liftgate ................... 66 Manual Liftgate .............. 119 Power Liftgate ..............120 Obstacle Detection ............. 120 Ignition Positions ..............100 Lights Indicator Lights.
Page 244 Replacing the Battery. See M Lights, Warning ..............49 Airbag Readiness ............. 51 Reprogramming Multi-Function Fobs ......118 Anti-Lock Brake System (ABS) ........50 Multi-Function Lever Brake System Warning ............. 50 Rear Window Washer and Wiper ........62 Charging System .............. 51 Windshield Washer ............
Page 245 Ramp OFF Switch ............132 Maintenance ..............80 Ramp Retraction/Deployment - Mechanical Override 130 Operation and Adjustment ..........76 Retraction ..............129 Pretensioner ..............77 Wheelchair Access Ramp Warranty Coverage ....5 Warnings ................76 Rear Window Wearing Seat Belts Properly ..........78 Defroster Operation ............
Page 246 Mobility Ventures’ Participation In The Better Business Technical Specifications ..........232 Bureau Mediation/Arbitration Program..... 14 Trip Odometer ................ 55 MV-1 Limited Warranty ............. 3 Items Not Covered by Warranty ........6 Tire Warranty ..............6 What is Covered ............. 3...
Page 247 Wheelchair Wiper ................61 Loading ................123 Wiper Blades ................ 226 Cleaning Instructions ............. 229 Occupant Restraints ............90 Restraints ................85 Securing ................86 Wheels and Tires Alignment ..............208 Tire Rotation .............. 208 Cleaning Instructions ............. 228 Damage ................205 Flat Tires ................
Page 249 P / N P T 0 1 8 6 3 5...

This manual is also suitable for:

Pt020713

MV-1 PT018635 Owner's Manual

Warranty

MV-1 Limited Warranty

Federal Requirements for Emissions Warranties

Federal Emissions Defect Warranty Coverage

Federal Emissions Performance

California Requirements for Emissions Warranties

Limitations and Disclaimers

Mobility Ventures' Participation in the Better Business Bureau ® Mediation/Arbitration Program

Introduction/Features

Instrument Cluster

Vehicle Controls

Seating and Safety Restraints

Driving

Liftgate/Power Swing Door/Ramp

Roadside Emergencies

Maintenance

Quick Links

Chapters

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for MV-1 PT018635

Summary of Contents for MV-1 PT018635