Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Technidea ZIPLEVEL PRO-2000
- Page 2 ZIPLEVEL SYSTEM CONCEPT INTRODUCTION You’re about to enter an exciting new labor saving world of elevation mea- +20’ (6m) surement and leveling. The ZIPLEVEL PRO-2000 High Precision Altimeter ® lets you focus on your work rather than the tedious task of measuring your work.
-
Page 3: Table Of Contents
INTRODUCTION TABLE OF CONTENTS Use any of ZIPLEVEL’s 16 powerful built-in functions to master tough ele- ZIPLEVEL Basics ......1-6 ® vation measuring and leveling tasks from estimating, planning, excavation, LABELED Quick Start ........construction and landscaping to fabrication, checking and analysis. Attach On/Off, Hold &... -
Page 4: Ziplevel Basics
1 ▪ ZIPLEVEL BASICS ZIPLEVEL PARTS ▪ 2 ZIPLEVEL consists of a Base Unit (BU) and hand-held Measurement Mod- To remove the boot: Serial Port ® 1. Place against chest ule (MM) joined by a rugged wireless Cord that communicates elevation data 2. - Page 5 3 ▪ MEASUREMENT MODULE MEASUREMENT MODULE ▪ 4 Use the Measurement Module to level and take readings. The bottom and Display reading is equivalent for measurements H = Display Measurement taken from back or bottom. Module Rotated back of the Module are the only sides that may be used interchangeably for measurements.
- Page 6 5 ▪ KEYPAD KEYPAD & DISPLAY ▪ 6 Use the keypad on the Measurement Module to control the ZIPLEVEL Flashes when Flashes when calibration is ® required due to temperature. battery is low. take readings. The most frequently used functions, called labeled functions, Flashes when re-zero required are printed on the eight keys below the display.
-
Page 7: Quick Start
7 ▪ QUICK START MECHANICS OF USE ▪ 8 Most ZIPLEVEL users will use only those functions routinely necessary in ® Typical Handling Suggested Reeling Technique their work. We suggest that you try all ZIPLEVEL functions at least once ® Manage Cord with left hand, gently ‘whip’... - Page 8 9 ▪ LABELED FUNCTIONS HOLD & ZERO ▪ 10 This section describes how to operate ZIPLEVEL’s labeled functions. Press HOLD before the Module is in position - the reading will lock on the display when movement stops. HOLD Glance through all the functions and illustrations then try each function on ZERO here first the ZIPLEVEL...
-
Page 9: Scale & Resolution
11 ▪ SCALE & RESOLUTION SCALE & RESOLUTION ▪ 12 SCALE SCALE Fractional inches Press for 2 seconds and continue to press or press and release to select fractional inches (”), decimal inches (IN), engineer’s feet (FT), builder’s Decimal inches feet-inches (FT-IN), centimeters (CM) or meters (M). -
Page 10: Calibration
13 ▪ CALIBRATION CALIBRATION ▪ 14 Unlike rotary lasers and optical levels, the ZIPLEVEL is not tilt sensitive, Step 1 Press CAL 2 seconds to start 3 beep tone. ® Step 2 Lay bottom or back down close to its level plane does not develop tilt error and it does not amplify error with Base Unit and press CAL again distance or require factory calibration. -
Page 11: Record
15 ▪ RECORD RECORD ▪ 16 The RECord function eliminates extensive tabulation and computation re- Can compute average, minimum and maximum error from level around forms. quired to average large numbers of readings. Now you can easily estimate the slurry necessary to level an uneven concrete surface, the fill needed below concrete or predict the graded level of a hilly lot (see illustrations). -
Page 12: Mark
17 ▪ MARK MARK ▪ 18 The MARK function lets you create audible tones: 1) at a selected elevation, Tones can supplement display to level or alarm MARK at height limits. 2) for elevations within a selected band, or 3) elevations outside a selected band. - Page 13 19 ▪ HIDDEN FUNCTIONS HIGH PRECISION ▪ 20 TEMPERATURE Feet Format HIGH To display ambient temperature, continue to press ON/OFF for 2 seconds PRECISION when turning ON. Momentarily press any other key to exit temperature. HIGH PRECISION The High Precision function lets you measure with an unprecedented paper thin 0.005”...
-
Page 14: Carry
21 ▪ CARRY CARRY ▪ 22 The CARRY function lets you leap-frog the Measurement Module and Base Can measure the height of a mountain or locate an elevation across town – no pencil, paper or CARRY Unit to measure elevations (differential level) over any distance or elevation calculator needed. -
Page 15: Record Data
23 ▪ RECORD DATA RECORD DATA ▪ 24 ZIPLEVEL can be used to record measurement data for creating tables, Saves up to 137 measurements, or an unlimited number with a PC. ® Take measurements over a grid of regular surface intervals for a contour or 3D map. profiles, sections, contour or 3D maps. -
Page 16: Inspect/Dump & Initialize
25 ▪ INSPECT/DUMP & INITIALIZE INSPECT/DUMP ▪ 26 INSPECT or DUMP Press CAL and REC two seconds to enter or exit INSPECT INSPECT These functions allow inspection of Record Data registers and/or data /DUMP Press CAL and REC momentarily and release to DUMP data to PC transfer to a PC. -
Page 17: Elevation
27 ▪ ELEVATION ELEVATION ▪ 28 Elevation lets you preset the display and Carry reference plane to a bench- Allows preset of elevation in CARRY function. First place measurement module at benchmark. ELEV mark elevation in engineers (FT) or metric scales for use in the CARRY function. -
Page 18: Monitor
29 ▪ MONITOR DISPLAY ALARM INDICATORS ▪ 30 The Monitor function can be used to keep the ZIPLEVEL from shutting off Flashes if unit needs to be re-calibrated due to a 36F (20C) tempera- ® ture change since last calibration. CAL is on constantly when unit is during periods of inactivity. -
Page 19: Use Tips
31 ▪ USE TIPS HOW TO MEASURE ACCURATELY ▪ 32 1) Secure the Base Unit after removing the Measurement Module. ZIPLEVEL isothermal readings are typically precise to within 0.2% of mea- ® surements 10’ (6m) or less and 0.35% of measurements beyond 10’ (6m). 2) Extend the Unipod from the top down and retract from the bottom up (see It can typically level to within 0.1”... -
Page 20: Ziplevel Care ▪ 34
33 ▪ HOW TO MEASURE ACCURATELY ZIPLEVEL CARE ▪ 34 6) Always secure the Base Unit to prevent movement during measurements ZIPLEVEL is rugged, durable and designed to provide years of reliable ® – it does not need to be level. performance when properly used. -
Page 21: Trouble Shooting ▪ 36
35 ▪ ZIPLEVEL CARE TROUBLE SHOOTING ▪ 36 6) Pack up the ZIPLEVEL when not in use for extended periods of time. ® Problem Action Never leave out in foul weather or overnight. Avoid storage inside a hot closed vehicle or trunk. Unit won’t turn on or shuts off Replace battery soon after turn on... -
Page 22: Maintenance/Product Assistance
37 ▪ MAINTENANCE/PRODUCT ASSISTANCE SPECIFICATIONS ▪ 38 Technidea Corporation warrants the ZIPLEVEL PRO-2000 High Precision Set-up vertical range: 40’ (12m) (20’ (6m) above and below Base Unit) ® 48”(122cm) full range in High Precision (HP) Altimeter against deficiencies in materials and workmanship for one year Set-up horizontal range: 200’...
Need help?
Do you have a question about the ZIPLEVEL PRO-2000 and is the answer not in the manual?
Questions and answers
How do I replace the battery?
To replace the battery in the Technidea ZIPLEVEL PRO-2000:
1. Use a coin, screwdriver, or your thumbnail to loosen the battery door screw.
2. Lift the terminal end of the 9V alkaline battery with your thumbnail, or tap the Measurement Module against your hand to release and catch the battery.
3. Insert a new 9V alkaline battery.
4. Note: The protective Boot is easier to remove when warm.
This answer is automatically generated