1. Manuals
  2. Brands
  3. Tanaka Manuals
  4. Trimmer
  5. TCG 24EC
  6. Handling instructions manual

Tanaka TCG 24EC Handling Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Grass Trimmer/Brush Cutter
Model TCG 24EC (SL) / TCG 27EC (S)
TCG 27EC (SL)
Handling instructions
Note:
Before using this machine, carefully read through these HANDLING INSTRUCTIONS
to ensure effi cient, safe operation. It is recommended that these INSTRUCTIONS be
kept readily available as an important reference when using this machine.
TCG24EC (SL)

Advertisement

Table of Contents
loading

Related Manuals for Tanaka TCG 24EC

Summary of Contents for Tanaka TCG 24EC

  • Page 1 Grass Trimmer/Brush Cutter Model TCG 24EC (SL) / TCG 27EC (S) TCG 27EC (SL) Handling instructions TCG24EC (SL) Note: Before using this machine, carefully read through these HANDLING INSTRUCTIONS to ensure effi cient, safe operation. It is recommended that these INSTRUCTIONS be...
  • Page 2 TCG27EC(S) TCG24EC(SL) TCG27EC(SL)
  • Page 5 0.6 mm...
  • Page 6 10 cm 11-14 cm 11-14 cm...

  • Page 7: Meanings Of Symbols

    MEANINGS OF SYMBOLS NOTE: Some units do not carry them. Symbols WARNING The following show symbols used for the machine. Be sure that you understand their meaning before use. Grass Trimmer / Brush Cutter Priming pump It is important that you read, fully understand and observe the following safety precautions Guaranteed sound power level and warnings.

  • Page 8: Warnings And Safety Instructions

    Guaranteed sound power level LwA by 2000/14/ Vibration level by ISO 22867 WA, Ra(G) hv, eq(R) Rear or Right handle / Equivalent* Racing 2000/14/EC Vibration level by ISO 22867 Uncertainty hv, eq(F) Front or Left handle / Equivalent* Before using your machine •...
  • Page 9 Do not operate in areas where there are tree roots or ○ Keep others away when making carburetor adjustments. rocks. ○ Use only genuine Tanaka replacement parts as ○ For respiratory protection, wear an aerosol protection recommended by the manufacturer.

  • Page 10: Specifications

    If situations occur which are not covered in this manual, take NOTE care and use common sense. Contact Tanaka dealer if you You may need to adjust the position of the hangar (16) need assistance. to balance the unit. To do so, loosen bolt (17) and adjust the position of hangar (16).

  • Page 11: Operating Procedures

    ○ The trimmer is equipped with a two-stroke engine. WARNING Always run the engine on fuel, which is mixed with oil. For Tanaka heads, use only fl exible, non-metallic line Provide good ventilation, when fueling or handling fuel. recommended by the manufacturer. Never use wire or ○...

  • Page 12: Maintenance

    Tanaka dealer. ○ With nylon cord cutters, always use over 15 cm of cord. CAUTION If the length of the cord is too short, rotation speed will Ensure that the throttle outer end is in the holder.
  • Page 13 ○ When replacing blade, purchase one recommended by The spark plug condition is infl uenced by: Tanaka, with a 25.4 mm (one inch) fi tting hole. ○ An incorrect carburetor setting. ○ In the case of a 3 or 4 tooth blade (41), it can be used on ○...

  • Page 14: Selecting Accessories

    Cover the unit and store it in a dry area. Maintenance schedule Below you will fi nd some general maintenance instructions. For further information please contact Tanaka dealer. Daily maintenance ○ Clean the exterior of the unit. ○ Check that the harness is undamaged.
  • Page 15 SELECTING CUTTING ATTACHMENTS Recommended accessories for each model are presented in the table below. For purchases, contact Tanaka dealer. Please check carefully as those accessories not marked with “ ” cannot be attached. ● List of recommended accessories BIKE Specifi cation...

  • Page 16: Troubleshooting

    TROUBLESHOOTING Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the Tanaka dealer. Condition Cause Remedy Fill the fuel tank with the correct fuel mix...
  • Page 17 Remedy Set the choke lever to START position to stop the engine Engine does not stop Stop switch failure Cease use immediately and contact Tanaka dealer Engine stops when throttle is Idle speed is too low Contact Tanaka dealer closed...
  • Page 18 Model TCG24EC (SL) TCG27EC (SL) TCG27EC (S) 23.9 26.9 — TORCH L7RTC (NGK BPMR7A) (min 2800 – 3200 Idle Max. (min 9900 9,900 (min 7500 (kW) 0.72 0.81 (kg) — / mm) pA, eq (dB(A)) 84 / 3 84 .1 / 3 84.6 / 3 ISO22868 WA, Ra(M)
  • Page 19 6684764 944458 875769 6698711 6699756 6696448 6696184 6696454...
  • Page 20 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. E99703411 NA Printed in China...

This manual is also suitable for:

Tcg 27ec

Table of Contents