Related Manuals for JohnsonFit PRE-WAXED
Summary of Contents for JohnsonFit PRE-WAXED
- Page 1 Read this tReadmill guide before using the owneR’s manual. PRe-waXed...
-
Page 2: Important Precautions
Failure to comply will void the warranty. IMPORTANT this treadmill has a pre-waxed belt and should never be lubricated or waxed. lubricating or waxing the belt can cause damage that is not covered by the warranty. - Page 3 dANGER WARNING TO REdUCE THE RISk Of ElECTRICAl SHOCk: TO REdUCE THE RISk Of bURNS, fIRE, ElECTRICAl SHOCk OR INjURy TO PERSONS: always unplug the treadmill from the electrical outlet immediately after using and before cleaning, performing maintenance and putting on or •...
-
Page 4: Grounding Instructions
GROUNdING INSTRUCTIONS BasiC oPeRation this product must be grounded. if a treadmill should malfunction or break down, grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock. this product is equipped with a cord having an equipment-grounding conductor and a grounding plug. -
Page 5: Location Of The Treadmill
fOldING THE TREAdMIll lOCATION Of THE TREAdMIll Place the treadmill on a level surface. we would advise there should be 214 cm (7 feet) of Firmly grasp the back end of the treadmill. Carefully lift the end of the treadmill deck into the upright 1 ft 31 cm clearance behind the treadmill, 92 cm (3 feet or same width as your treadmill) on each side... -
Page 6: Using The Heart Rate Function
USING THE HEART RATE fUNCTION WIRElESS HEART RATE RECEIVER Your treadmill could be equipped with either heart rate pulse grips or a thumb pulse sensor. to find out what your model has, refer to some treadmills also include a built-in wireless heart rate receiver. when used in conjunction with a wireless chest transmitter, the beginning of the assemBlY section of your owneR’s manual. -
Page 7: Maintenance
IMPORTANT this treadmill has a pre-waxed belt and should never be lubricated or waxed. lubricating or waxing the belt can cause damage that is not covered by the warranty. -
Page 8: Every Week
AfTER EACH USE (dAIly) TENSIONING THE RUNNING bElT Clean and inspect, following these steps: For more information and/or how-to videos, visit our Customer support section on our • turn off the treadmill with the on/oFF switch, then unplug the power cord at the wall outlet. website. -
Page 9: Centering The Running Belt
CENTERING THE RUNNING bElT tRouBlesHooting For more information and/or how-to videos, visit our Customer support section on our website. CAUTION do not run belt faster than 4 km/h / 3 mph while centering. Keep fingers, hair and clothing away from belt at all times. If the running belt is too far to the right side: using the supplied allen wrench bElT IS TOO fAR TO THE RIGHT SIdE and with the treadmill running at 4 km/h / 3 mph turn the lEfT adjustment bolt... -
Page 10: Common Product Questions
COMMON PROdUCT QUESTIONS plugged into a power strip/surge protector or extension cord. bASIC TROUblESHOOTING • Verify that the power cord is not pinched or damaged and is PROblEM: the console does not light up. properly plugged into the outlet and the machine. ARE THE SOUNdS My TREAdMIll MAkES NORMAl? •... - Page 11 PROblEM: the belt does not move or moves briefly, but the and not on a gFCi-equipped outlet. do not plug the • Verify that you do not have the machine on an console works. machine into a power strip/surge protector or extension extension cord or surge protector.
-
Page 12: Troubleshooting Heart Rate
TROUblESHOOTING HEART RATE if this troubleshooting section does not remedy the problem, discontinue use and turn the power off. (GRIP-PUlSE ONly) PlEASE REfERENCE CONTACT INfORMATION fOR Check your exercise environment for sources of ASSISTANCE. interference such as fluorescent lights, computers, underground fencing, home security systems or appliances the following information may be asked of you when you call. - Page 13 © 2012 Vision treadmill guide (pre-waxed) 062612’...