Summary of Contents for TouchLink TLP Pro 520M
- Page 1 User Guide TouchLink ™ TLP Pro 520M and TLC Pro 521M TouchLink Touchpanel Control System 68-2153-01 Rev. B 06 16...
- Page 2 Safety Instructions Istruzioni di sicurezza • Italiano Safety Instructions • English WARNING: This symbol, , when used on the product, is intended AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad avvertire to alert the user of the presence of uninsulated dangerous voltage l’utente della presenza di tensione non isolata pericolosa all’interno del within the product’s enclosure that may present a risk of electric shock.
- Page 3 AVTrac, Cable Cubby, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, FlexOS, GlobalViewer, Global Configurator, Hideaway, Inline, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System INTEGRATOR, TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTP Systems...
- Page 4 FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
- Page 5 Conventions Used in this Guide Notifications In this user guide, the following are used: Potential risk of severe injury or death. WARNING: AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. CAUTION: Risk of minor personal injury. Risque de blessure mineure. ATTENTION : ATTENTION: •...
-
Page 7: Table Of Contents
Configuration Software Introduction ............1 ........19 Configuration Software ........19 About the TLP Pro 520M and TLC Pro 521M ..1 Features ............. 1 Installing GUI Designer, Global Configurator, and Toolbelt ..........20 Additional Features of TLP 520M ....2 Additional Features of TLC 521M .... - Page 8 TLP Pro 520M and TLC Pro 521M • Contents viii...
-
Page 9: Introduction
This guide describes the function, installation, and operation of the TLP Pro 520M and TLC Pro 521M TouchLink Pro touchpanels. Unless otherwise stated, the terms “TLP Pro” and “touchpanel” refer to both the TLP Pro 520M and TLC Pro 521M. This section contains the following items: •... -
Page 10: Additional Features Of Tlp 520M
A controller is integrated into the TLC Pro 521M, so no external controller is required with this model. NOTE: The TLP Pro 520M is not compatible with Extron IP Link (non-Pro) controllers. TLP Pro 520M and TLC Pro 521M • Introduction... -
Page 11: Application Diagram
Application Diagram Figure 1 shows a typical application for the TLP Pro 520M. The TLC Pro 521M can be used in similar applications. NOTE: The TLC Pro 521M does not require an external controller. Extron TLP Pro 520M Laptop Tuner... -
Page 12: Installation Overview
This section contains an overview of the installation process. Follow the links for a more detailed explanation of each step. Before starting, download and install the latest versions of the following software: GUI Designer — for designing layouts for Extron TouchLink Pro touchpanels and … third party touch interfaces. - Page 13 Set up the Touchpanels for Network Communication: Connect the PC that you will use for setup and the touchpanel to the same Ethernet … subnetwork. The TLP Pro 520M, also requires a control processor on the same Ethernet subnetwork. Use the...
-
Page 14: Panel Features
TLP Pro 520M and TLC Pro 521M Rear Panel Features TLP Pro 520M and TLC Pro 521M Front Panel Features Figure 2 shows the front panel features for the TLP Pro 520M. The TLC Pro 521M is identical. C DB Figure 2. - Page 15 (see figure 2 on the previous page) — The TLP Pro 520M and TLC Pro 521M ship with a black front bezel in the landscape orientation. If required, use the included removal tool to detach the bezel. Accessory kits, which must be purchased separately, are available for white bezels and bezels in the portrait orientation.
-
Page 16: Tlp Pro 520M And Tlc Pro 521M Rear Panel Features
TLP Pro 520M and TLC Pro 521M Rear Panel Features The rear panels of the TLP Pro 520M and TLC Pro 521M are identical except for the RS-232, Relay, and IR/S ports on the TLC Pro 521M. RS-232 Relay IR/S... - Page 17 Code part 1, section 16. • Cette installation doit toujours être en accord avec les mesures qui s’applique au National Electrical Code ANSI/NFPA 70, article 725, et au Canadian Electrical Code, partie 1, section 16. TLP Pro 520M and TLC Pro 521M • Panel Features...
- Page 18 NOTE: The pulse function is absolute: it always sets the relay state to closed, times out (briefly), then opens the contact. It overrides the previously selected setting (on state, off state, or toggle). TLP Pro 520M and TLC Pro 521M • Panel Features...
- Page 19 • TLP Pro 520M IP address: 192.168.254.251 Touchpanel • Gateway IP address: 0.0.0.0 LAN Port • Subnet mask: 255.255.255.0 • DNS address: 127.0.0.1 • DHCP: off • DNS: 127.0.0.1 Figure 7. Network and PoE Connector TLP Pro 520M and TLC Pro 521M • Panel Features...
- Page 20 Network Environment 0 per IEC TR62101. • Le TLP Pro 520M et le TLC Pro 521M sont conçu pour une connexion à un circuit PoE pour une utilisation intérieure seulement et est considéré comme faisant partie d’un environnement réseau 0 par IEC TR62101.
- Page 21 The power supply shall not be permanently fixed to building structure or similar structure. • La source d’alimentation ne devra pas être fixée de façon permanente à une structure de bâtiment ou à une structure similaire. TLP Pro 520M and TLC Pro 521M • Panel Features...
-
Page 22: On-Screen Menus
Pressing this button Exit applies and saves any changes and closes the menu screens. In this section, the figures will show the screens for the TLP Pro 520M. The screens for the TLC Pro 521M are similar. Status Screen This screen opens by default. -
Page 23: Network Screen
• Shift Press to save the new name. • Enter If DHCP is disabled, set the unit , and IP address subnet mask gateway address TLP Pro 520M and TLC Pro 521M • On-screen Menus... - Page 24 The buttons Revert change back to gray. If you have not made any changes, the buttons are grayed out. Apply Revert TLP Pro 520M and TLC Pro 521M • On-screen Menus...
-
Page 25: Display Screen
• Click sets the volume for audible feedback that accompanies events such as a screen button being pressed. • Sounds sets the volume of audio from any audio file playback. TLP Pro 520M and TLC Pro 521M • On-screen Menus... -
Page 26: Advanced Screen
Advanced Screen To open the screen, click in the top menu bar. Advanced Advanced There are small differences between the TLP Pro 520M and the TLC Pro 521M, which are shown in figure 15. Display Audio Advanced Exit Status Network... -
Page 27: Configuration Software
The GUI Designer and the Global Configurator Plus and Professional programs provide versatility and adaptability for configuration and control of an AV system as it grows and evolves. TLP Pro 520M and TLC Pro 521M • Configuration Software... -
Page 28: Installing Gui Designer, Global Configurator, And Toolbelt
Toolbelt without returning to the Extron Download page. Toolbelt — If you choose to download Global Configurator and Toolbelt separately, • click the button next to the program and follow the on-screen instructions. Download TLP Pro 520M and TLC Pro 521M • Configuration Software... -
Page 29: Using The Software
Use the Setup Menu (see page 14) or Toolbelt to configure the touchpanel network settings. Figure 19 shows the TLP Pro 520M Web page. The TLC Pro 521M Web page is similar. Extron Electronics ® General Status... -
Page 30: Updating Firmware
. The firmware file is uploaded to the touchpanel. Follow the on-screen Upload instructions. Updating Firmware Using Toolbelt For complete information about using Toolbelt to update the touchpanel firmware, see the Toolbelt Help File. TLP Pro 520M and TLC Pro 521M • Configuration Software... -
Page 31: Mounting
ATTENTION: • Do not install the TLP Pro 520M or the TLC Pro 521M in a fire resistant rated wall or partition assembly. • Ne pas installer le TLP Pro 520M ou le TLC Pro 521M dans un mur résistant au feu ou une cloison. - Page 32 TLP Pro 520M snaps to wallplate adapter (2 places on each side). Mounting Screws (2) Remove Bezel. Figure 22. Mounting the TLP Pro 520M TLP Pro 520M and TLC Pro 521M • Mounting...
-
Page 33: Other Mounting Options
Other Mounting Options Extron provides a range of mounting kits for the TLP Pro 520M and TLC Pro 521M. These allow the touchpanel to be mounted on glass surfaces, desktops (fixed or swivel mount), rack mounted (see below for important guidelines about rack mounting), and wall mounted, with a wall box. -
Page 34: Reference Material
Touchpanels For information about network port requirements and licensed third-party software for the TLP Pro 520M or the TLC Pro 521M, please refer to the Pro Series Control Product Network Ports and Licenses Guide, which is available at www.extron.com. -
Page 35: Project Recovery (Tlc Pro 521M Only)
The unit returns to its pre-recovery mode state and settings. • The Power LED returns to being steadily lit. Run or Stop Program (TLC Pro 521C only) This mode toggles between stopping and starting programs. TLP Pro 520M and TLC Pro 521M • Reference Material... -
Page 36: Reset All Ip Settings
1 second. Result Reset All IP Settings mode: • Sets the IP address back to factory default (192.168.254.251 for the TLP Pro 520M and 192.168.254.252 for the TLC Pro 521M). • Sets the subnet back to factory default (255.255.255.0). - Page 37 Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to: USA, Canada, South America,...
Need help?
Do you have a question about the TLP Pro 520M and is the answer not in the manual?
Questions and answers