Summary of Contents for quiko QK E3000
- Page 1 230V /400V MOTOR FOR SLIDING GATES ERCOLE QK E3000 QK-E3000T USE AND MAINTENANCE MANUAL www.quikoitaly.com V01_2011...
-
Page 2: Table Of Contents
C O N T E N T S TECHNICAL FEATURES…………………………………………………………………….2 DIMENSIONS………………………………………………………………………………….2 PRE-INSTALLATION CONTROL…………………………………………………………...2 MATERIALS FOR INSTALLATION…………………………………………………………3 INSTALLING THE COUNTERPLATE………………………………………………………3 POSITIONING THE GEARMOTOR…………………………………………………………4 INSTALLING THE RACK……………………………………………………………………..4 FASTENING AND ADJUSTING OF THE END LIMIT SWITCHES……….……………..5 UNLOCKING THE MOTOR MANUALLY…………………………………………………..5 ADJUSTING THE CLUTCH………………………………………………………………….5 GENERAL ADVICE…………………………………………………………………………...6 USE……………………………………………………………………………………………..6 MAINTENANCE………………………………………………………………………....6... -
Page 3: Technical Features
Quiko Italy is liable only for products it manufactures and commercializes. Once automated, the gate becomes a machine and is therefore subjected to the rules of the “ Machinery Directive”. It is on the installer to verify its security. WARNING: Quiko Italy Sas is not liable for any damages to people, animals or things due to unauthorized modifications, alterations or betterments on its products by third parties. -
Page 4: Materials For Installation
MATERIALS FOR INSTALLATION Fig. B Gear-motor Counter plate 2 end cams (or runners) Nylon rack INSTALLING THE COUNTERPLATE Dig the foundations at least 15 cm deep. Supply a protective cable sheath. Attach it to the ground using concrete, completely covering the foundation of the plate. -
Page 5: Positioning The Gearmotor
POSITIONING THE GEARMOTOR Once the concrete has hardened, insert the screws to fasten to the counterplate or, eventually, the concrete. Fig. D INSTALLING THE RACK A. Gear motor Fig. E B. Screws Fig. E Once a hole has been made in the door, fasten the rack to the gate with self-threading screws based on the measurements listed in Figure F www.quikoitaly.com... -
Page 6: Fastening And Adjusting Of The End Limit Switches
FASTENING AND ADJUSTING OF THE END LIMIT SWITCHES (CAMMES) ISSAGGIO E REGOLAZIONE DEI PATTINI DI FINECORSA Position the end limit switches as in fig. G, each of them near an end of the rack. By manually moving the door, place the end limit switches so they activate the spring connected to the micro-switch just before the mechanical stops at the end of the rail;... -
Page 7: General Advice
GENERAL ADVICE Install a gate’s safety system that complies with current regulations. Choose short routes for cables and keep power cables separate from control ones. Install the control card in a waterproof box. Please refer to current regulations when setting the gear motor’s maximum torque. We advice you to install an outdoor switch, in compliance with European standards on the issue of safety, to turn the electricity off when servicing the gate. -
Page 8: Typical System
MAIN COMPONENTS ELECTRICAL CABLES’ CROSS SECTION a - 2x0,5 mm GEAR MOTOR b - 4x0,5 mm PHOTOCELLS c - 3x0,5 mm KEY SELECTOR d - 3x1 mm FLASHING LIGHT e - 2x0,5 mm AERIAL RG59 f - 4x0,5 mm PHOTOCELLS ON LITTLE COLUMNS g - 4x0,5 mm GATE STOPPERS RAIL... - Page 9 DECLARATION OF CONFORMITY (OF THE MANUFACTURER) Manufacturer: QUIKO ITALY SAS Via Seccalegno, 19 36040 Sossano (VI) Italia hereby declares, under his liability, that the products: QK-E3000, QK-E3000T are in compliance with the essential safety requirements of the regulations: Electromagnetic Compatibility Directive ......2004/108/EC Low Voltage Directive ............2006/95/EC...
- Page 10 DECLARATION OF CONFORMITY (OF THE INSTALLER) The undersigned: Address: in charge of the set-up, declares that the product: Gate type: Location: are in compliance with the essential safety requirements of the regulations: Electro magnetic Compatibility Directive ......2004/108/EC Low Voltage Directive ............2006/95/EC Machinery Directive ..............2006/42/EC and also declares that the related and/or specific national technical regulations have been followed:...
- Page 11 www.quikoitaly.com...
- Page 12 QUIKO ITALY Via Seccalegno, 19 36040 Sossano (VI) - Italy Tel. +39 0444 785513 Fax +39 0444 782371 info@quiko.biz www.quikoitaly.com...