Sealey PMG100.V2 Instructions Manual
  1. Manuals
  2. Brands
  3. Sealey Manuals
  4. Welding System
  5. PMG100.V2
  6. Instructions manual

Sealey PMG100.V2 Instructions Manual

Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTIONS FOR
GASLESS
MIG W W ELDERS
P P M M G G 1 1 0 0 0 0 . . V V 2 2
Models:
P P M M G G 1 1 1 1 0 0 . . V V 2 2
P P M M G G 1 1 3 3 5 5 X X T T . . V V 2 2
P P M M G G 1 1 5 5 5 5 X X T T . . V V 2 2
PMG100.V2, PMG110.V2, PMG135XT.V2, PMG155XT.V2 - 2 - 120407

Advertisement

Table of Contents
loading

Related Manuals for Sealey PMG100.V2

Summary of Contents for Sealey PMG100.V2

  • Page 1 P P M M G G 1 1 3 3 5 5 X X T T . . V V 2 2 P P M M G G 1 1 5 5 5 5 X X T T . . V V 2 2 PMG100.V2, PMG110.V2, PMG135XT.V2, PMG155XT.V2 - 2 - 120407...
  • Page 2 GASLESS MIG WELDERS PMG100.V2, PMG110.V2, PMG135XT.V2 & PMG155XT.V2 Thank you for purchasing a Sealey welder. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: BEFORE USING THIS PRODUCT, PLEASE READ THE INSTRUCTIONS CAREFULLY. MAKE CAREFUL NOTE OF SAFETY INSTRUCTIONS, WARNINGS AND CAUTIONS.

  • Page 3: Introduction And Description

    Ensure that you understand the properties and associated hazards before using a gas. " Spray the gas cup and contact tip regularly with anti-spatter spray available from your Sealey dealer. " Store gas cylinders in a vertical position only and ensure that the storage area is correctly secured.
  • Page 4 4.6.2. Tension between rollers is checked by slowing down the wire between your fingers. If the top feed roller skids the tension is correct.Use as low a tension as possible, too high a tension will deform the wire and result in a blown fuse. PMG100.V2, PMG110.V2, PMG135XT.V2, PMG155XT.V2 - 2 - 120407...
  • Page 5 " 0.8mm Aluminium Wire (MIG/2/KAL08) 6.4. Other You can use large industrial gas cylinders if preferred (the machine is no longer portable). To do so, contact your local Sealey dealer to obtain an industrial regulator and cylinder adaptor kit. fig. 11 fig.

  • Page 6: Rating Plate

    2) The weld area must also be free of paint, rust, grease, etc. 3) If welding a vehicle, disconnect the battery or fit an “Electronic Circuit Protector” (available from your Sealey dealer). 7.3.2. The following table is an estimated duration of cylinders based on a flow rate of 2ltr/min.

  • Page 7: 10. Troubleshooting

    Incorrect distance of torch to workpiece Torch distance should be 8-10mm. 15. Fuse blowing Tension too great Reduce tension (Section 4). Gas cup contact tip clogged Clean gas cup and contact tip (Section 9). PMG100.V2, PMG110.V2, PMG135XT.V2, PMG155XT.V2 - 2 - 120407...
  • Page 8 11.10. Screening and shielding. Selective screening and shielding of other cables and equipment in the surrounding area may alleviate problems of interference. Screening of the entire welding/cutting installation may be considered for special applications. PMG100.V2, PMG110.V2, PMG135XT.V2, PMG155XT.V2 - 2 - 120407...

Table of Contents