Summary of Contents for Yukon CLM-150
- Page 1 CLM-150 ® Competitor Lat Machine Yukon International, Inc. Bedford Heights, OH 44146 23700 Aurora Rd. www.yukon-fitness.com Fax: (440) 439-0030 (800) 799-8566 (440) 439-0000...
-
Page 2: Parts List
Congratulations on your decision to purchase the Yukon Competitor Lat Machine. The team at Yukon has designed this fitness machine using the finest materials possible to deliver superior quality and value in your home year after year. Please follow the assembly instructions carefully, and regularly inspect the completed unit to insure all hardware is in place and properly attached. - Page 3 1 3/16” x 2 3/8” End Plug (x 5) (x 1) (x 3) (x 1) 2” Open End Cap 1” Round Plug Hand Grip Locking Pin (x 1) (x 2) (x 4) (x 1) Yukon® CLM-150 Rev. C Fitness Issued 12/08/2004 Equipment...
- Page 4 • You use this machine at your own risk, so please exercise carefully and with caution. NOTE: When installing cables, make sure the washer is in front of the ball. If it is not, then slide the ball to the other end of cable. Incorrect Correct Yukon® CLM-150 Rev. C Fitness Issued 12/08/2004 Equipment...
- Page 5 YUKON INTERNATIONAL, INC. YUKON FITNESS EQUIPMENT Assembly Instructions Competitor Lat Machine Step 1. • Slide a rubber donut (5) onto the bottom of each slide rod (6) • Insert each slide rod (6) through the outer 1" holes of the rear base (4).
- Page 6 3/8” x 4 1/4” bolts (2), four 3/8” washers (3), and two 3/8” nuts (4). 1. Front base 2. 3/8” x 4 1/4” Hex bolt 3. 3/8” Washer 4. 3/8” Nylon nut 5. Upright Yukon® CLM-150 Rev. C Fitness Issued 12/08/2004 Equipment...
- Page 7 1. 3/8” x 4 1/4” Hex bolt 2. 3/8” Washer 3. Upright 4. 3/8” Nylon nut 5. Boom 6. 5/16” x 3/4” Hex bolt 7. 5/16” Washer Pre-installed Parts: A. 1 9/16” x 3 1/8” End plug Yukon® CLM-150 Rev. C Fitness Issued 12/08/2004 Equipment...
- Page 8 (3) and push a foam roller (1) onto each end. 1. Foam roller 2. 1” Round tube 3. Foam roller post Pre-installed Parts: A. 1” Round plug B. 1 3/4” x 1 3/4” End plug Yukon® CLM-150 Rev. C Fitness Issued 12/08/2004 Equipment...
- Page 9 5. 3/8” Nylon nut 6. Boom 7. Upright 8. 3/8” x 3 3/8” hex bolt 9. Pulley plate 10. Bolt end of Upper cable 11. 1/2” Nut 12. 1/2” Washer 13. Top plate Yukon® CLM-150 Rev. C Fitness Issued 12/08/2004 Equipment...
- Page 10 (example: bicep curls, upright rows, shrugs, etc…). Failure to do so may result in the tipping or lifting of machine. 1. Foot plate 2. Pull pin 3. Front base Yukon® CLM-150 Rev. C Fitness Issued 12/08/2004 Equipment...
- Page 11 1. Low pull bar 2. Snap link 3. Chain 4. Lower cable 5. Lat bar 6. Upper cable 7. Weight selector Pre-installed Parts: A. Hand grip Yukon® CLM-150 Rev. C Fitness Issued 12/08/2004 Equipment...