Panasonic DMP-BD60GN Operating Instructions Manual page 33

Changing the speaker setting to suit your speakers [BD80]
When connecting to an amplifier/receiver to enjoy multi-channel surround sound, use the following settings on this unit if they cannot be set on
the amplifier/receiver.
The settings are effective when connecting to analog 7.1ch AUDIO OUT/5.1ch AUDIO OUT terminal.
Preparation
1 Set "Analog Audio Output" to "7.1ch" or "2ch (Downmix) + 5.1ch".
( 31)
A message is displayed.
2 Press [OK].
Center (C)
ms
L
Front (L)
0.0
dB
0.0
Complete
Complete
Test
Test
dB
LS
0.0
dB
LB
0.0
(LS) Surround (RS)
Surround back channel is enabled only when setting "Analog
§
Audio Output" to "7.1ch".
Speaker presence and size (
Set all the connected speakers individually.
1 Press [3, 4, 2, 1] to select the speaker icon and press [OK].
2 Press [3, 4] to select the setting and press [OK].
Icon examples:
Surround speaker (LS)
≥Large: Select when
the speaker
supports
low-frequency (under 100 Hz) reproduction.
Select when the speaker does not support
≥Small:
low-frequency reproduction.
In order to make an ideal listening environment, settings of speaker
sizes may be automatically adjusted.
For example, if the subwoofer is set to "No", the front speakers will
automatically be set to "Large". (In this case, we recommend
connecting a speaker that can reproduce bass below 100 Hz.)
To finish the speaker setting
Press [3, 4, 2, 1] to select "Complete" and press [OK].
dB
C R
Front (R)
0.0
dB
0.0
dB
SW
Subwoofer
0.0
(SW)
ms dB
RS
0.0 0.0
ms dB
RB
0.0 0.0
Surround back
(LB) (RB)
§
)
L R
C
SW
LS RS LB RB
LS
LS
Large Small No
Delay time ( )
ms
0.0
For optimum listening with 7.1/5.1-channel sound, all the speakers,
except for the subwoofer, should be the same distance from the
seating position.
If you have to place the center, surround and surround back
speakers closer to the seating position, adjust the delay time to
make up for the difference.
If either distance A or C is less than B (
difference in the relevant table and change to the recommended
setting.
1 Press [3, 4, 2, 1] to select the delay time box (
press [OK].
2 Press [3, 4] to select the setting and press [OK].
5.1ch speaker
7.1ch speaker connection
connection
Approximate room dimensions
C
L C R L
A
B
SW LS
LS
C
LS RS LB
LB
LS RS
Circle of constant primary listening distance
A Center speaker
Difference Setting
Approx. 34 cm 1.0 ms
Approx. 68 cm 2.0 ms
Approx. 102 cm 3.0 ms Approx. 340 cm
Approx. 136 cm 4.0 ms Approx. 510 cm
Approx. 170 cm 5.0 ms
Channel balance ( )
dB
0.0
1 Select "Test" and press [OK].
A test signal is output.
Front (L)_—)Center (C)_—)Front (R)_—)Surround (RS)
:
Surround (LS)(— Surround Back (LB) (— Surround Back (RB)
2 While listening to the test signal, press [3, 4] to adjust the
volume of each speaker
Front speakers: 0.0 to s6.0 dB
Center speaker, Surround/Surround Back speakers:
0.0 to s12.0 dB
3 Press [OK].
The test signal stops.
≥No signal is output for the subwoofer. To adjust its volume, play
something, then return to this screen to adjust to suit your taste.
below) find the
ms ) and
0.0
: Actual
C
speaker
C R
position
SW
: Ideal
A
B
speaker
RS
RS
C
position
C
A B C
RB
: Primary
listening
RB
distance
C Surround/Surround back
speakers
Difference Setting
Approx. 170 cm 5.0 ms
10.0 ms
15.0 ms
;
RQT9407
33