1. Manuals
  2. Brands
  3. RSS Manuals
  4. Music Mixer
  5. M-400
  6. Owner's manual

RSS M-400 Owner's Manual

Hide thumbs Also See for M-400:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
Version 2.1 Owner's Manual Addendum
This document describes the features that have been added in this update.
In order to fully understand the M-400's new features, please read this document together with the Owner's Manual for the M-400.
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.

Advertisement

Table of Contents
loading

Related Manuals for RSS M-400

Summary of Contents for RSS M-400

  • Page 1 Version 2.1 Owner’s Manual Addendum This document describes the features that have been added in this update. In order to fully understand the M-400’s new features, please read this document together with the Owner’s Manual for the M-400. Copyright © 2010 ROLAND CORPORATION...

  • Page 2: Functionality Added In Version

    • A feature for making the input/output settings on the S-4000M has been added. M-400 does not support REAC EMBEDDED POWER. When you connect an S-0808, install an external battery on the S-0808 to power it via the DC IN port.
  • Page 3 Functionality added in version 2.10 ● Display of the insert destination has been added to the GEQ EDIT and FX EDIT popups (Dual GEQ). fig.GEQ_Guide.eps ● A delay time indicator has been added to the "SDE-3000 x2" effect type. This flashes in time with the delay time. fig.Sde3000_Guide.eps ●...
  • Page 4 CONFIGURATION popup. fig.S4M_Config_Guide.eps Merge Patchbay This merges the inputs of the REAC slave units (connected to the REAC ports 1–4 of the S-4000M) into the channels to the M-400’s REAC port. Output Patchbay This assigns channels from the M-400 to the outputs of the S-0808 units ( REAC ports 1–4).
  • Page 5 S-4000M’s Input/Output Settings Accessing the S-4000M CONFIGURATION Resetting S-4000M Input/Output Setups popup (System Reset) You can reset and optimize the merge/output patchbays according to the In the SETUP section, press [SYSTEM] to access the devices physically connected to REAC ports 1–4. SYSTEM screen.

  • Page 6: Merge Patchbay Operations

    S-4000M’s Input/Output Settings Merge Patchbay Operations Acesss the S-4000M CONFIGURATION popup. REAC Channel indication This indicates the number of the REAC channels being sent to the Press [F1 (MERGE)] to access the MERGE tab. 400. fig.S4M_Config_IN_Guide.eps Input indication This indicates the input numbers of the REAC slave device and the signal level s.

  • Page 7: Output Patchbay Operations (S-0808)

    Access the S-4000M CONFIGURATION popup. This indicates the number and the signal level of the REAC channels Press [F2 (OUTPUT)] to access the OUTPUT tab. being sent from the M-400. fig.S4M_Config_OUT_Guide.eps The color indicates the signal level as follows.: Color...

  • Page 8: Splitting Merged Inputs (S-4000M's Split Function)

    By using the S-4000M’s Split Function, you can split the merged inputs Using S-4000M’s split function (being sent to the M-400) to REAC port 4 of the S-4000M. It is very convenient when splitting to a monitor console or a multi-channel recording system.
  • Page 9 Pressing [F7 (CANCEL)] will cancel the operation. Press [F4 (LOAD/SAVE)]. fig.S4M_LoadSave_Guide.eps Do not disconnect the USB memory or switch off the M-400’s power while data is being saved to USB memory. Doing so may destroy the data saved in USB memory.

  • Page 10: Gate/Expander Popup

    New Functionality for Dynamics About the New Functionality for Dynamics About the New Functionality for Dynamics fig.ChEdtEQ.eps You can now manipulate dynamics parameters using the EQUALIZER area knobs in the CHANNEL EDIT section. When one of the following popups is displayed, you can use the Q, FREQ, and GAIN knobs for LO MID and HI MID to adjust the on-screen parameters. •...
  • Page 11 New Functionality for Dynamics ● EXPANDER Expander fig.PopExpGuide.eps Knob Parameter EQ LO-MID Blink Threshold level FREQ Blink ATTACK time GAIN Blink RELEASE time EQ HI-MID Blink RATIO FREQ Blink KNEE GAIN Disabled Unlit ● DUCKING Knob Parameter EQ LO-MID Blink Threshold level THRESH knob FREQ...

  • Page 12: Compressor Popup

    New Functionality for Dynamics RELEASE knob ATTACK knob This adjusts the RELEASE time in a range of 0 ms–8000 ms. This is the This adjusts the ATTACK time in a range of 0.0 ms–800.0 ms. This is time over which the ducking effect disappears after the HOLD time the time from when the input signal exceeds the threshold level until has elapsed.

  • Page 13: Limiter Popup

    New Functionality for Dynamics LIMITER popup When the LIMITER popup is displayed, the limiter can be adjusted using the EQ area controls for the CHANNEL EDIT section. The FREQ, fig.PopLmtGuide.eps and GAIN knobs for EQ LO and HI are disabled at this time. The parameter that you can manipulate using the EQ area is as follows.
  • Page 14 New Functionality for User Faders About the New Functionality for User Faders • The user faders have been increased to three layers. • The way you access the user faders has also been changed. [F7 (CANCEL)] Cancels the changes and closes the popup. Editing the user fader assignments [F8 (OK)] Confirms the changes and closes the pop-...
  • Page 15 New Functionality for User Faders Press [F8 (CLOSE)] to finalize the changes and close the USER FADER ASSIGN popup. Press [F8 (OK)] to finalize the changes and close the USER PREFERENCE popup. If you press [F7 (CANCEL)], the changes will be cancelled and the USER PREFERENCE popup will close.
  • Page 16 New Functionality for the Input Channels New Functionality for the Input Channels CH 1–48 PRE EQ PRE FADER POST FADER MUTE FADER 4BAND AUX SEND 1–16 SEND PRE EQ LINK PRE FADER POST FADER MUTE SEND PRE EQ PRE FADER POST FADER DIRECT OUT PRE EQ...

Table of Contents