Sealey CP2400.V4 Instructions For

Sealey CP2400.V4 Instructions For

1/2” sq. drive 325lb.ft

Advertisement

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Wear ear
Refer to
Instruction
Protection
Manual
1. SAFETY
1.1. GENERAL SAFETY
Follow all workshop safety rules, regulations and conditions when using the wrench.

Remove the battery pack from the wrench before servicing or performing any maintenance.

Maintain the wrench and battery pack in good condition. Check moving parts for alignment on a regular basis.

Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be

dangerous and will invalidate the warranty.
Ensure the wrench is 'locked' before installing the battery pack.

Keep the wrench, battery pack and charger clean for optimum performance.

Keep the work area clean and tidy and free from unrelated materials. Ensure that there is adequate lighting.

Ensure that battery pack is correctly inserted into the wrench handle and latched in place before operating wrench.

WARNING! When working around vehicle brake systems we recommend that you wear suitable respiratory protection due to the
R
possible presence of asbestos dust from brake linings.
U se only impact sockets which are specifically designed for use with an impact wrench.

Avoid unintentional starting.

Wear approved safety eye/face shield, ear defenders and hand protection.

R emove ill-fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.

M aintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

Keep children and unauthorised persons away from the work area.

DO NOT operate the wrench if any parts are missing as this may cause failure and/or personal injury.

DO NOT use the wrench unless you have been instructed in its use by a qualified person.

DO NOT operate the wrench where there are solvent fumes or flammable gases, liquids or solids.

DO NOT leave the wrench operating unattended.

DO NOT carry wrench with your finger on the trigger. Keep direction switch in 'locked' position when not in use.

DO NOT use the wrench for a task it is not designed to perform.

DO NOT operate the wrench when you are tired or under the influence of alcohol, drugs or intoxicating medication.

DO NOT get the wrench or battery charger wet or use in damp or wet locations.

K eep wrench and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 40°C (104°F).

1.2.
Battery safety instructions
WARNING! The battery pack contains nickel-cadmium, which is dangerous. It must therefore be handled with care.
R
C harge the battery pack prior to first use. The battery pack will have been shipped in a low charge state.

Use only the charger provided to charge the battery pack.

DO NOT charge the battery pack when room temperature is below 10°C (50°F) or above 40°C (104°F).

DO NOT attempt recharging the pack by means of an engine generator or a DC power source.

DO NOT short-circuit the battery pack by touching both terminals at the same time with a metal object, or your fingers etc.

DO NOT store battery pack (or wrench) in locations where the temperature may exceed 40°C (104°F) e.g. in outside sheds, above

heaters etc.
WARNING! Dispose of spent battery pack correctly as it contains nickel-cadmium.
R
DANGER! DO NOT attempt to disassemble the battery pack. For safety and environmental reasons DO NOT discard in domestic waste
V
or by burning. ONLY discard or recycle according to local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your person. If you come into contact with battery liquid take the following
R
immediate action: a) Skin contact: Wash immediately with soap and water, then wash in either lemon juice or vinegar.
b) Eye contact: Wash with a strong solution of boric acid and seek immediate medical attention.
1.3.
MAINS POWER ELECTRICAL SAFETY (In relation to the battery charger)
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
R
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets
and any other connectors for wear or damage. You must ensure the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board.
We also recommend that a Residual Current Device (RCD) be used. It is particularly important to use an RCD with portable products that
© Jack Sealey Limited
INSTRUCTIONS FOR
CORDLESS IMPACT WRENCH 24V
1/2" SQ. DRIVE 325LB.FT
MODEL NO:
Wear a mask
Wear eye
Protection
Original Language Version
CP2400.V4
CP2400.V4 | Issue 2(L) 15/04/15

Advertisement

Table of Contents
loading

Summary of Contents for Sealey CP2400.V4

  • Page 1 CP2400.V4 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2: Operation

    RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
  • Page 3: Using The Wrench

    5.1.1. Keep the outer case of the wrench clean and free from grease. DO NOT wash with water or use solvents or abrasives. Use a damp cloth. 5.1.2. For any other service or maintenance, contact your authorised service agent. 5.2. LUBRICATION If the wrench has not been used for some time, remove the lubrication screw (fig.1.2) and inject grease into the impact mechanism, DO NOT overfill - a small amount each time should be sufficient. Original Language Version CP2400.V4 | Issue 2(L) 15/04/15 © Jack Sealey Limited...
  • Page 4 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Sole UK Distributor, Sealey Group. 01284 757500 www.sealey.co.uk Kempson Way, Suffolk Business Park, Bury St.
  • Page 5 WARNING! – Risk of Hand Arm Vibration Injury. This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately. This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC. This tool is to be operated in accordance with these instructions. Measured vibration emission value (a): ..13.48 m/s² Uncertainty value (k):.

Table of Contents