Related Manuals for HiBoost Hi13-23
Summary of Contents for HiBoost Hi13-23
-
Page 1: User Manual
User Manual HiBoost Hi13-23 Triple, quadruple and quintuple band consumer boosters 10 - 27dBm power range... -
Page 2: Table Of Contents
Booster’s Port Description ....................9 LCD Introduction ....................... 9 Control Button operation ....................11 Manual gain control (MGC) ..................12 Install Hiboost Booster System ..................13 Before You Install ...................... 13 Installation Overview ....................13 Step 1. Install Outdoor Antenna ..............15 Step 2.Install Indoor Antenna ................ -
Page 3: Preface
Preface This user manual describes design, installation, commissioning and maintenance of Hiboost wide band consumer single and dual band boosters. Please, read user manual carefully before installing and maintaining the boosters. The information in this manual is subject to change without prior notice. Opinions are welcomed about the manual improvement. -
Page 4: Overview
Overview Hiboost triple, quadruple and quintuple band consumer boosters are designed to help mobile users to amplify weak cell phone signal. The devices are bi-directional. The outdoor antenna receives the signal from the cell tower and transmits it to the signal booster, the booster amplifies the signal and the indoor antenna sends it to your mobile device. - Page 5 Quadruple band booster Diagram Quintuple band booster Diagram...
-
Page 6: Glossary Of Terms
Glossary of Terms Item Definition LTE800 Available on LTE800(832~862MHz/791~821MHz) network E-GSM900 Available on EGSM900(880~890MHz/925~935MHz) and PGSM900(890~915MHz/935~960MHz), WCDMA/UMTS900(880~915MHz/925~960MHz) networks LTE1800 Available on GSM/LTE1800(1710~1785MHz/1805~1880MHz) networks 3G-2100 Available on 3G(WCDMA/UMTS2100) (1920~1980MHz/2110~2170MHz) networks LTE2600 Available on LTE2600(2500~2570MHz/2620~2690MHz) network Radio Frequency Attenuation Automatic Level Control Automatic Gain Control Manual Gain Control Low Noise Amplifier... -
Page 7: Package Contents
Package Contents Name Description Quantity Hiboost triple, quadruple or quintuple band booster N-female Adapter 12V/7A Plastic expansion bolt Φ8 Tapping screw M6*50 User manual If it is a kit, please find below additional kit accessories Outdoor panel antenna 5D-FB Cable... -
Page 8: Features
Features Embedded CPU, self-adaptive intelligent system very easy to use and install, better performance is guaranteed even under complicated and constantly changing RF environment conditions. ISO: Intelligent isolation processing to avoid self-oscillation, quite wide adjusting range to stabilize the signal strength/quality for clearer voice/ higher data speed and avoid interference with mobile networks. -
Page 9: Booster's Port Description
Booster’s Port Description 1. LCD2. Control Button 3. Power connector 4. Outdoor antenna port 5. Indoor antenna port 6.Set LCD Introduction After the repeater is on, gain and power will light up on the screen. “Band”– displays the working frequency. Find below the list of frequencies displayed corresponding to the networks. - Page 10 Frequency Band display LTE800 LTE800 EGSM&UMTS900 E-GSM900 GSM<E1800 LTE1800 WCDMA2100 3G-2100 LTE2600 LTE2600 “ULdB”“ DLdB“– gain indication. The displayed value shows real-time uplink and downlink gain. “Power dBm“– power indication. The displayed value shows real-time power. When repeater’s output power is lower than -10dBm, the value will display ”---”.
-
Page 11: Control Button Operation
”OFF”- repeater shut-down alarm indication. When LCD screen is in ”OFF” state and the repeater shuts down, LCD screen will be flashing. When LCD screen is ”ON” and the repeater shuts down, the “OFF” is flashing. Press ”Query” key and LCD screen will display ”OFF” under the current band. Control Button operation There are 4 operation modes: long press on ”Query”... -
Page 12: Manual Gain Control (Mgc)
Manual gain control (MGC) Since the booster has intelligent software system, MGC attenuation is not needed, except for the cases when you don't feel comfortable about ISO or ALC flashing, or in some extreme cases you might need to attenuate gain value. When LCD is in the fixed display mode, press “Query”... -
Page 13: Install Hiboost Booster System
Install Hiboost Booster System Before You Install • Make sure you have sufficient cable length between the outdoor/indoor antennas and the booster in case you have not a standard kit • Make sure the place where you install the booster is near to one existing electrical outlet. - Page 14 Booster System Installation Options Studio apartment Duplex house Multi-storey building 1. Outdoor Antenna2.Booster 3.Indoor Panel Antenna4.Power Supply Omni CeilingAntenna7. 5.Splitter 6. Indoor Panel Antenna...
-
Page 15: Step 1. Install Outdoor Antenna
Step 1. Install Outdoor Antenna 1.1 How to find the place with the strongest receiving signal The booster’s main function is to improve weak RF signal inside a house, office or any other indoor area. The receiving strength of the outdoor antenna and the strength of the signal reception outdoors directly affect the efficiency of indoor coverage. - Page 16 Remark: when ALC shows up flashing, it means the receiving signal power is stronger than the system needs it. It is recommended to adjust outdoor antenna position unless ALC alarm disappears. Or you can leave it as it is to let the booster self-adjust automatically.
- Page 17 band yagi antenna as an option. Pole mounting is recommended for your convenience: Step1: Use an existing pole or obtain a pole of 1 to 2 inches in diameter and install it in the desired location. Step2: Unscrew nuts from the antenna base by hands or with a wrench, if needed. Fix horizontal plate of the L-bracket on the antenna base with screws.
-
Page 18: Step 2.Install Indoor Antenna
Step 2.Install Indoor Antenna Select indoor panel antenna or omni-ceiling antenna as an indoor antenna according to your needs to provide indoor coverage. Install the indoor panel antenna as shown on the graph below. Step1: Select a place on a wall in the area where you need better reception. Normally, to provide an overall coverage, you will need to choose a corner. -
Page 19: Step 3.Install Signal Booster
Step 3.Install Signal Booster 1. Select the location near a power supply on a wall. 2. Mount the booster with the screws included into the kit as shown on the graph below. 3. Connect the outdoor antenna cable to booster connector marked as “outdoor”. -
Page 20: Step 4.Booster Commissioning
Step 4.Booster Commissioning Overview: The booster has an intelligent startup system, booster commissioning is an automatic process able to guarantee system optimal performance. As soon as you finish booster system installation, plug it in a power supply to power on the booster. It will start working and checking the receiving signal and the isolation to ensure best system performance. - Page 21 1. The rated output power is reached, but the coverage is not enough or the signal in specific areas isn’t improved: Check whether the indoor antenna is installed correctly or not, try to • change the antenna position to improve coverage. Check if it is necessary to adjust the direction of the indoor antenna.
- Page 22 ISO status indicates if the booster has enough isolation between outdoor and indoor antennas in order to avoid loop back or so-called self-oscillation. Thanks to intelligent software, HiBoost is fully protected from interference with operator mobile networks. "ISO" flashing on LCD display means that ISO function is working great and the self-oscillation has been eliminated.
- Page 23 More about "ALC" indication: ALC indicates the strength of input signal or receiving power of the booster. Flashing ALC means that the booster has strong receiving power. Status Meaning Solution methods Check coverage, leave it as it is if it’s good;...
- Page 24 More about LCD indication: Status Meaning Solve methods Check coverage, leave it if it is good; take below actions to increase signal if coverage is not good. Output power is 1. Adjust the antenna direction or “---” status lower than location to get stronger receiving -10dBm signal...
-
Page 25: Main Specifications
Main Specifications RF Parameter 880~915MHz 925~960MHz 1800 1710~1785MHz 1805~1880MHz Frequency Range 2100 1920~1980MHz 2110~2170MHz 832~862MHz 791~821MHz 2600 2500~2570MHz 2620~2690MHz Hi13 60dB 65dB Hi17 65dB 65dB Max. Gain Hi20 65 dB 70dB Hi23 70dB 75dB Hi13 17dBm 13dBm Hi17 17dBm 17dBm Max. -
Page 26: Troubleshooting
Hiboost signal boosters are covered with2-year warranty. Huaptec offers two options for the products under warranty: repair or replace. This warranty does not apply to HiBoost signal boosters or kits that have been subjected to misuse, abuse, neglect or mishandling and that have its physical or electronic properties altered or damaged. -
Page 27: Huaptec Contact Details
Huaptec Contact Details Huaptec CN Huaptec EU Huaptec US Phone/Fax: 086-0755-29921615 Address: 5th FL, E BLDG, Phone/Fax: (44)20 3239 5808, Phone/Fax: (972) 870-5666 Sogood Science Address: Benno-Strauß-Street Address: 6210 N Belt Line Rd., Park, Hangkong Road, Xixiang, 7, 90763 Fürth, Germany Ste.
Need help?
Do you have a question about the Hi13-23 and is the answer not in the manual?
Questions and answers