Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for MVP D3 SERIES
- Page 1 PRODUCT INSTRUCTIONS CAMERA ENCLOSURES D3 SERIES...
- Page 2 D3 Component Checklist for camera installation / Camera Mount Bracket ...................... 4 Intro to MVP Power ...................................... 5 24V Input MVP Power ....................................6 High Voltage Input MVP Power ..................................7 Camera Power Setup (Standard 12VDC Connector and NON-STANDARD 12VDC CONNECTOR) ................8 Camera Installation (Generic) ..................................9 Steady Step Mounting Instructions .................................
-
Page 3: Limited Warranty
LIMITED WARRANTY DOTWORKZ PRODUCTS DOTWORKZ SYSTEMS INC. Warrants this Product to be free from defects in material or workmanship, as follows: PRODUCT CATEGORY PARTS LABOR All Enclosures and Electronics One (1) Year One (1) Year Power Supplies One (1) Year One (1) Year The limited warranty stated in these product instructions is subject to all of the following terms and conditions: 1. - Page 4 PRODUCT INSTALLATION PRECAUTIONS – WARNINGS – ADDITIONAL INFORMATION (RETAIN THIS DOCUMENT) IMPORTANT SAFEGUARDS Read Instructions - All the safety and operating instructions should be read CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE before the unit is operated. COMPONENTS TO WATER OR MOISTURE Retain Instructions -The safety and operating instructions should be retained for The lightning flash with an arrowhead...
-
Page 5: Electrical Conduit Guidelines
Electrical Conduit Guidelines For optimal performance, your Dotworkz Enclosure is designed to be Air & Water Tight to eliminate any moisture, dust, and insect damage, safety, performance, reliability, and maintenance related issues. Use of Electrical Conduit, without sealing the entry ports/ inside wire feeds within Camera Enclosure, will subject the inside of your enclosure to possibility of condensation driven moisture, dust, and insect contamination hazards. - Page 7 Component Check List For D3 Included Standard Hardware for Camera Mounting 24V Input Blue Bypass Cable In MVP models only Optional Camera Mount Bracket for Larger Cameras #RP-AXBR (AB-1007) Optional RP-AXBR Bracket Direct Compatibility: (Available by special order) Axis 231D, & 232D...
- Page 8 Output Voltage to Power Camera MVP provides step down voltage to supply camera power for 12VDC, and 24V Cameras. 24V Camera Supply 24V output depends on Site Power Input, for either 24V Direct Current, or Alternating Current (see table above)
- Page 9 Input Power Configuration for 24 VAC/ VDC Inside all D3-MVP is a Chassis similar to shown Site Power Available 110 – 220 VAC Power Source Step Down Transformer Single Phase Only High Voltage to 24 VAC All Wiring Connections are...
- Page 10 *All Wiring must be done by a Qualified technician Voltage Input to hook up inside D3 *Observe all local and applicable electrical codes Inside all D3-MVP is a Chassis similar to shown Site Power Available All Wiring Connections are 110 – 220 VAC Power Source –...
- Page 11 All D2 environmental enclosures come standard with a 12VDC Right Angle Barrel Plug (3.3mm x 5.5mm with a 1mm center pin) for majority of the IP cameras on the market. Right Angle Standard Inline version If you IP camera’s power connector is different but still accepts up to ~ 13VDC for power, please see our section on Camera Power Setup (NON-STANDARD CONNECTOR) for instructions on how to power your camera.
- Page 12 Align camera on D3 camera bracket so as to center camera’s “pan” axis directly over center of camera plate provided. The D3 camera bracket has been pre-drilled with most of the popular camera mounting hole patterns. Align pre-drilled holes on camera plate to best fit your camera model. Use hardware provided to secure to D3 camera plate. On some camera models, new holes may need to be drilled by installer to secure to D3 camera bracket, or for installer to provide misc.
- Page 13 Steady Step Mounting System Steady Step Bracket Steps adjust in ¼” increments. To adjust 1/8” between step settings, add 1/8” brass male-male hex stand-off (ITEM NO. 6) shown in detail D (below), and provided in D3 hardware pack, by threading on top of movable slide bracket of steady step bracket system, then fastening camera bracket (CB-1007 or AB-1007).
- Page 15 COOLDOME Input Power Configuration: D3-CD-12VDC Turn Off Power or leave power disconnected during Installation of All Wiring. Follow all local and relevant electrical codes & standards. Test all Wiring and confirm correct voltages before wiring up & powering up COOLDOME. Provided P/S: SP500 Site Power Available Must be Housed Indoors, or in...
- Page 16 COOLDOME Input Power Configuration: D3-CD-12VDC Warning!!!: COOLDOME Enclosure runs on 12 VDC only! If high voltage is applied directly to COOLDOME enclosure, you will damage housing, void warranty, and create electrocution hazard that can be harmful or fatal. Do not start wiring until you have fully read and understand these installation instructions.
- Page 17 D3 High Voltage Power Supply Specifications D3 COOLDOME SP-500-12 Power Supply D3 MVP Models – High Voltage Inputs...
- Page 18 D3 Exploded Detail...
- Page 19 D3 Mounting Detail...
Need help?
Do you have a question about the D3 SERIES and is the answer not in the manual?
Questions and answers