Page 2
Congratulations on your purchase of a quality power tool from Erbauer (UK) Ltd. This product should give you reliable service but for your peace of mind this power tool does carries a 24-month guarantee, the terms of which are detailed below.
SAFETY INSTRUCTIONS Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Page 4
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
may cause irritation or burns. Service a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. ADDITIONAL SAFETY INSTRUCTIONS for cordless reciprocating saws 1.
Page 6
substitute for a shut-off switch. 13. Do not place the battery in or near fire, on stoves or other high temperature locations. Do not place the battery in direct sunlight, or use or store the battery inside cars in hot weather.
TECHNICAL DATA Charger volts 230V~50Hz Power No load speed 0-2,700min Max cutting depth in wood 177mm Max cutting depth in steel 12mm Stroke 22mm Battery capacity 2.6Ah Lithium-Ion Charging time 1 hour Machine weight 1.96kg ACCESSORIES 1h charger 2.6Ah li-ion battery packs 2pcs Saw blade for wood CSR18L.1-M-071008.indd 8...
Page 9
OPERATION INSTRUCTIONS Note: Before using the tool, read the instruction book carefully. 1. Before using your cordless reciprocating Your battery pack is UNCHARGED and you must charge once before use. Warning: The charger and battery pack are specifically designed to work together so Fig 1-1 do not attempt to use any other devices.
Page 10
Defective battery, after pre-charge 30 minutes with Red Flashing trickle current, the total Green Off battery voltage is still less than 15.0v. Red ON Charging Green Off Green ON Power On and Fully Red Off Charged Fig 3 The temperature of battery Green Flashing pack is less than 0℃...
floors, walls and other difficult areas. Insert the blade shank into the blade clamp with the blade teeth facing up (opposite to normal working position). This will make cuts closer to the work surface. 8. Pivoting shoe (See Fig.6) The pivoting blade shoe must be held firmly against the material being cut to reduce saw vibration, blade jumping and blade breakage.
help extend blade life. When cutting aluminum, use coolant. 12. Pocket cutting (Soft materials only. Do not plunge cut in metal surfaces.) Mark the pocket or internal hole to be cut out. Insert the special cutting blade with blade teeth facing down and clamp securely.
has reached the correct temperature. The normal discharging/working temperature is between 0 and 75 C.When the allowable battery temperature of 75 C is exceeded, the electronic control switches off the power tool until the temperature is in the optimum temperature range again. Battery pack overload and low-voltage protection When max.
PLUG REPLACEMENT If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Blue – Neutral Brown – Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.
Declaration of Conformity We, Importer Erbauer (UK) LTD BA22 8RT Declare that the product 18V LI-LON RECIPROCATING SAW ERI067RSP Complies with the essential health and safety requirements of the following directive: 98/37/EC EC Machinery Directive 2006/95/EC EC Low Voltage Directive...
Need help?
Do you have a question about the ERI067RSP and is the answer not in the manual?
Questions and answers