Table of Contents
Summary of Contents for Tri-Tek Electronics PS-120
- Page 1 INSTALLATION / OPERATING MANUAL High Speed Mini PTZ Camera P/N : 388058205 PRINTED IN KOREA Distributed by Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. PRECAUTIONS 1. 1 Important Safety Instruction 1. PRECAUTIONS • Read these instructions. 1. 1 Important Safety Instruction ................... • Pay attention on all the warnings. 2. GETTING STARTED • Follow all instructions. 2. 1 Features ........................ •... -
Page 3: Getting Started
2. GETTING STARTED 2. 1 Features 2. 3 Selection Flow Auto-Focus - The camera adjusts the focus automatically while monitoring the screen continuously Type Indoor Outdoor in the auto mode. It built in 12x zoom lens, when used in combination with its 32x digital zoom, the camera achieves a zooming capability of up to 384x. -
Page 4: Installation
3.Installation 3. 1 Address / communication setting 3. 3 Indoor Ceiling The following steps of installation and connection work should be done by qualified service personnel or system installers and should conform to all local codes. ▶ ADDRESS( ID) setting S/W NO 1 1 28 ▶... -
Page 5: Indoor In Ceiling
3. 4 Indoor In Ceiling 3. 5 Outdoor (Ceiling Bracket) The mounting has to be installed onto a firm and stable location where all the parts may be completely The mounting has to be installed onto a firm and stable location where all the parts may be completely secured. -
Page 6: Outdoor (Wall Bracket)
4. MAIN SETUP MENU 4. 1 Initialize 3. 6 Outdoor (Wall Bracket) The mounting has to be installed onto a firm and stable location where all the parts may be completely When the device is powered on, you can check the address, secured. - Page 7 - LABEL Setting - TOUR NO Press key. NEAR TOUR MENU PRESET LABEL EDIT <001> TOUR MENU Select character by using joystick and press key. NEAR LABEL : PRESET 001 TOUR NO : 01 DEFINE LABEL TOUR EDIT < > <STORE TELE MOVE...
- Page 8 3) Scan - Start POSITION By using Scan function, the camera moves between 2 positions if there is no PTZ command after SCAN MENU SCAN START POSITION passing the assigned Dwell time. When there is no camera movement, the Scan function runs and the camera moves from the position assigned as the start point to the position assigned as the end point SCAN NO : 01 DEFINE...
- Page 9 - DWELL - LABEL The Scan function runs after the Dwell time without any camera SCAN MENU PATTERN LABEL EDIT <01> PATTERN MENU movement. SCAN NO : 01 DEFINE LABEL : PATTERN NO : 01 UNDEFINE Select ON/OFF by using joystick and press key.
- Page 10 - START PAN POSITION 5) AREA The Area function means that it displays the Area name between two programmed pan positions. AREA MENU AREA START POSITION Maximun 16 Area functions are toured in order. AREA NO : 01 DEFINE LABEL START PAN POS : 000.0 STOP PAN POS...
- Page 11 - ALARM NO “Save” above setting Alarm data to the memory. ※ - "Save" above setting data to the memory. ALARM SELECT AREA MENU - "CLR" means above setting Pattern data will not be saved and be cleared. - "BACK" means it goes back to the previous menu. ALARM NO : 01 UNDEFINE LABEL...
-
Page 12: Dome Menu
4. 3 Dome Menu - TIME ＊TIME (MIN) : The Park time can be assigned from 10 sec to 60sec. (Max. 2min./ by 10 sec.) PARK MENU Pan, Tilt, Zoom motion is adjustable in the “Dome Setting” Menu. TIME : 02MIN MAIN MENU FUNCTION : PRESET... - Page 13 - RESPONSE 5) DOME SUB MENU *Send the intrinsic protocol value to the Tx line. (Only for Pelco-D 5.0) DOME MENU DOME MENU TILT LIMIT : OFF Select ON/OFF by using joystick and press key. TITLE : NEAR SPEED BY ZOOM : OFF POWER UP ACTION : ON AUTO FLIP...
- Page 14 - HEATER ON TIME 7) FACTORY SET ＊Set the operating time of the heater. Restore all of setting value to the factory default. - By 10min. (10~60 min.) DOME MENU DOME MENU HEATER ON TEMP : 5 C All of existing setting value would be erased. TITLE : HEATER ON TIME : 30 MIN...
-
Page 15: Camera Menu
4. 4 Camera Menu 2) FOCUS In Focus menu, you can set up the focus mode among Auto, One Push or Manual. Camera menu is subject to change without prior notice to upgrade and quality increase and CAMERA MENU we may use slip sheet for the change. ZOOM MODE FOCUS MODE Please check the camera version and the slip sheet if the camera menu and this manual... - Page 16 - AF MODE - SHUTTER SPEED If you set SHUTTER in the AE MODE, you can control image AF MODE: Set the auto focus mode FOCUS MENU AUTO EXPO.MENU brightness by adjusting shutter speed. FOCUS MODE : AUTO Select : Set ON : AE MODE : MANUAL...
- Page 17 - WB MODE - AGC MODE WB MODE: Set the color depend on white balance. Select ON/ OFF in AGC MODE. WHITE BALANCE MENU AE EXPO.MENU Select AUTO, INDOOR, OUTDOOR, ONEPUSHWB, Select : Set ON : WB MODE : ATW ATW or MANUAL.
- Page 18 6) SPECIAL - HLC CLIP LEVEL In the Special menu, it’s available to set APERTUREGAIN, FLICKERLESS, BACK LIGHT HLC CLIP LEVEL : Select HLC function ON and set the HLC SPECIAL MENU DNR LEVEL and WDR. CLIP LEVEL.(0~06) MAIN MENU STABILIZER : OFF HLC MODE : OFF Select :...
-
Page 19: Specification
5. SPECIFICATION - BACK LIGHT 5. 1 Camera Specification Select ON/OFF in the BACK LIGHT function. SPECIAL MENU Image Sensor 1/4" SONY Super HAD II(Double Scan) CCD SUB SP MODE Total Pixels NTSC : 1028(H) × 508(V) PAL : 1028(H) x 596(V) Select : Set ON : NEAR... -
Page 20: Dimension
6. DIMENSION 6. 1 Dimension Ø8 Ø107.5 Ø172 Ø128 Ø4.5 Ø180.3 Ø107.5 Ø172 R53.8 Ø172... - Page 21 MEMO Ø128 Ø4.5 Ø180.3 R53.8 Ø164 161.6 132.4 R53.8...
Need help?
Do you have a question about the PS-120 and is the answer not in the manual?
Questions and answers