Blomberg DWT 25502 SS User Manual
Hide thumbs Also See for DWT 25502 SS:

Advertisement

Dishwasher
User manual
DWT 25502 SS
DWT 25502 B
DWT 25502 W
DW 25502 SS

Advertisement

Table of Contents
loading

Summary of Contents for Blomberg DWT 25502 SS

  • Page 1 Dishwasher User manual DWT 25502 SS DWT 25502 B DWT 25502 W DW 25502 SS...
  • Page 2: Table Of Contents

    10.1 CARING FOR YOUR DISHWASHER EXTERIOR 10.2 CARING FOR YOUR DISHWASHER INTERIOR 10.3 CLEANING THE FILTERS 10.4 CLEANING THE HOSE FILTER 10.5 CLEANING THE IMPELLERS 11. TROUBLESHOOTING 12. TECHNICAL FEATURES 13. WARRANTY STATEMENT FOR THE BLOMBERG DISHWASHERS 42 14. HOW TO GET SERVICE...
  • Page 3: Important Safety Instructions

    1. IMPORTANT SAFETY INTRODUCTION Please read this user manual and INSTRUCTIONS particularly the safety instructions WARNING:When using the completely and carefully. They will save dishwasher, follow basic you time and effort and help to ensure precautions, including the optimum dishwasher performance. following: Read all instructions before Be sure to observe all listed warnings...
  • Page 4 Use only detergents or rinse manufacturer’s recommendations. • aids recommended for use in a If a malfunction occurs, switch • household dishwasher and keep off the appliance and turn off the them in a dry place out of the water supply to the dishwasher. reach of children.
  • Page 5 run with the circuit conductors WARNING:If your and connected to the equipment- dishwasher is equipped with grounding terminal or lead on the internal illumination, lamp appliance. should only be replaced by This appliance produces ozone • the Authorised Service Agent within the washing compartment in case of failures that may during normal operation.
  • Page 6: Installation

    2. INSTALLATION property or bodily injury. Connect to a properly rated, • WARNING:When installing protected and sized power supply the dishwasher, follow basic circuit to avoid electrical overload. precautions, including the The dishwasher is designed for an following: electrical supply of 120 V (volts), 60 Hz (hertz), AC, connected to The dishwasher installation must be a dishwasher-dedicated, properly...
  • Page 7: Getting To Know Your Dishwasher

    3. GETTING TO KNOW YOUR DISHWASHER xxxxx xxxxx 1. Upper rack 2. Upper spray arm 3. Salt container (MODEL DEPENDING) 4. Cutlery basket 5. Detergent dispenser 6. Door 7. Control panel 8. Guiding track for the upper rack 9. Lower spray arm 10.
  • Page 8: Loading The Dishwasher

    4. LOADING THE Lower rack ( MODEL DEPENDING) DISHWASHER Pull the handle to open the door. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will continue. Upper rack ( MODEL DEPENDING) Bottom rack load pattern for 12 place settings according to the AHAM DW-1...
  • Page 9 Lower rack ( Now you can load the dishwasher. MODEL DEPENDING) Lower rack ( MODEL DEPENDING) International Loading Pattern – Bottom Additional Loading Pattern – Bottom rack (14 place settings) rack (10 place settings) Upper rack ( MODEL DEPENDING) CAUTION:Large knives and other utensils with sharp tips and edges must be placed horizontally into the upper...
  • Page 10: Upper Rack

    4.1 UPPER RACK CAUTION:The cup racks are designed to support cups, Load the upper rack with dessert glasses and kitchen utensils. plates, cups, glasses etc. When the cup racks are in the dishwasher do not lean on or use the cup racks to support your body weight.
  • Page 11 COLLAPSIBLE UPPER BASKET COLLAPSABLE UPPER BASKET TINES TINES (MODEL DEPENDING) (MODEL DEPENDING) There are foldable tines on the upper Upper basket of the machine is basket of the machine that you can lay equipped with wires with gradual down when you need larger space for folding system (A) that you can lay big dishes.
  • Page 12 FOLDING TINES (MODEL DEPENDING) There are “folding tines” in the upper rack to allow you more space to accommodate glasses or cups. Simply pull in the first front folding tine, move it to left A and right B to place in another positon.
  • Page 13: Lower Rack

    HEIGHT SETTING (MODEL DEPENDING) In certain models, the height setting of the upper rack may be changed using the wheels which are present at two height levels. CAUTION:Make sure that the rack is empty. Changing the height setting while the rack contains tableware Push the latches back into the could cause the contents to...
  • Page 14 FOUR FOLDING PLATE SUPPORT COLLAPSABLE LOWER BASKET TINES (MODEL DEPENDING) WIRES 4 PIECES-(MODEL There are 4 separate “folding plate DEPENDING) support tines” in the lower rack of The four piece foldable wires located your dishwasher designed to allow at the lower basket of the machine you more space to accommodate are designed for an easier placement saucepans, pots and large bowls in the...
  • Page 15 SILVERWARE BASKET (MODEL DEPENDING) Silverware basket is designed to wash your dishes such as knife, fork, spoon, etc. in a cleaner manner. Since the cutlery basket can be moved (A, B), you can create a wider space while placing your dishes to the lower basket and free up space for your dishes in different sizes.
  • Page 16 UPPER CUTLERY BASKET (MODEL DEPENDING) The upper cutlery basket is designed for small dishes, or long items that cannot fit into the lower cutlery basket. After taking out the basket by lifting it up, remove the carrier part from the rails by pulling it towards yourself (C).
  • Page 17: Proper And Improper Loading Of Dishware

    4.3 PROPER AND IMPROPER LOADING OF DISHWARE 4 4 4 1: Salad Fork 2: Teaspoon 3: Dinner fork 4 4 4 4: Knife-solid handle Sliding Cutlery Basket load pattern for 12 5: Serving spoon place settings according to the AHAM DW-1 6: Serving fork Standards •...
  • Page 18: What Should Not Be Washed In Your Dishwasher

    5. WHAT SHOULD NOT Crystal and very fine glassware • may become opaque (etch) losing BE WASHED IN YOUR their shine over time. You may DISHWASHER prefer to wash them by hand. Rust-sensitive steel parts like iron • Do not wash sponges or dish •...
  • Page 19: Operating The Product

    6. OPERATING THE PRODUCT 1. Display 5. Function keys 2. On/Off key Half Load Function 3. Start/Pause/Cancel key Sanitize Function 4. Time Delay key Extra Rinse function Rapid Clean 6. Program Selection keys 12. End of Programme indicator 7. Programme indicator 13.
  • Page 20: Keys

    6.1 KEYS 3. Press Programme Selection keys until the number of the programme On / Off key you selected appears on the It is used to turn on or off the machine. Programme indicator. Use P+ to Machine will turn on with economy switch to the next programme, and programme in On mode and the P- to switch to the previous one.
  • Page 22: Auxiliary Functions

    6.4 AUXILIARY FUNCTIONS Sanitize Function Sanitize function raises the water Washing programmes of your temperature in the final rinse to dishwasher are designed to obtain meet the requirements of NSF/ANSI the best cleaning effect, considering STANDARD 184 for Residential the type of the soil, soiling degree and Dishwashers.
  • Page 23 3. Select the desired programme Notice: Automatic detergent and press the Half Load key. The detection feature should be Half Load indicator will light on the deactivated during the tests display in the Function Selected according to AHAM DW-1. indicator. To deactivate: 4.
  • Page 24: Programming The Washing Time

    6.5 PROGRAMMING THE Programme and auxiliary WASHING TIME functions cannot be set/changed after the Time Delay programme has started. If an economical electricity tariff is applied in your region, you can use To cancel the Time Delay function the Time Delay function to wash your 1.
  • Page 25: Child (Key) Lock

    6.6 Starting the programme If the door is opened while To start your machine after selecting the machine is running, the the programme and auxiliary functions, machine will switch to the press Start / Pause / Cancel key. standby mode. Close the Once the programme starts a tune machine door and press is played and the estimated time...
  • Page 26: Cancelling The Programme

    For energy saving, the Adjusting the water hardness product is automatically level is explained in Water turned off following Softening System section. the completion of the 6.10 Rinse Aid indicator ( ) programme or if the Please check the rinse aid indicator programme is not started.
  • Page 27: Water Cut-Off Warning

    6.12 WATER CUT-OFF ProCare This programme is recommended WARNING to be operated on each 1-2 months If mains water is cut or water inlet for machine cleaning and necessary tap is turned off the machine cannot hygiene. The programme should be take water in and E:02 icon will flash operated while the machine is empty.
  • Page 28: Detergent & Rinse Aid Dispenser

    7. DETERGENT & RINSE AID DISPENSER 7.1 FILLING THE DETERGENT DISPENSER WARNING:Always store your detergent in locations which are cool, dry and out of the reach of children. Check that the detergent • dispenser is empty after the If you do not know the hardness completion of each wash of your water supply, use 15 ml / 3 program.
  • Page 29: Filling Rinse Aid Dispenser

    7.2 FILLING RINSE AID the 25 ml / 5 tsp mark. When the dishes are less dirty, it is generally DISPENSER sufficient to fill the detergent up to WARNING:Keep your the 15 ml / 3 tsp mark. rinse aids out of the reach of children.
  • Page 30: Set The Dose Of Rinse Aid

    Close the lid until it clicks in 3. Carefully wipe off spilled rinse aid. Excessive rinse aid causes excessive foam formation, which may hinder cleaning. 7.3 SET THE DOSE OF RINSE AID The dose of rinse aid to be used can be set by means of the dispenser regulator 4 between levels 1 and 6.
  • Page 31: Setting The Water Softener

    8. SETTING THE WATER SOFTENER (MODEL DEPENDING) WATER HARDNESS & REGENERATION SETTINGS The dishwasher requires lime free water. Hard water leaves watermarks on your dishes. Your dishwasher has a special water softening system to remove the hardness of the tap water. Setting this system correctly will increase the washing effectiveness.
  • Page 32: Filling The Dishwasher Salt Dispenser

    9. FILLING THE DISHWASHER If the hardness level of the water that you use is above 90°dF (French SALT DISPENSER standard for water hardness) or if (MODEL DEPENDING) you are using well water, than it is CAUTION :Never use recommended to use filter and water culinary or table salt.
  • Page 33: Care And Maintenance

    10. CARE AND MAINTENANCE Open the screw-in cap of the salt container by turning it counter WARNING:Before cleaning clockwise (Fig. A, B). or carrying out maintenance, switch off the appliance, disconnect the mains plug and turn off the water tap. WARNING:Do not repair or replace any part of the dishwasher or attempt any...
  • Page 34: Caring For Your Dishwasher Exterior

    10.1 CARING FOR YOUR 10.2 CARING FOR YOUR DISHWASHER EXTERIOR DISHWASHER INTERIOR NOTICE: Cleaning your CAUTION :Possible dishwasher at regular dishwasher damage: intervals ensures longer Abrasive cleaners, scouring product life and reduces the pads, abrasive cloths (paper risk of recurring problems. towels) can damage the Always disconnect the power dishwasher decorative door.
  • Page 35: Cleaning The Filters

    10.3 CLEANING THE FILTERS 4. Clean all three filters under tap water by means of a brush. Clean the filters at least once a week 5. Replace the metal/plastic filter. in order for the machine operates efficiently. Check if food residues are 6.
  • Page 36: Cleaning The Hose Filter

    10.4 CLEANING THE HOSE 10.5 CLEANING THE FILTER IMPELLERS Damages on the machine that may be Clean the impellers at least once a caused by impurities coming from the week in order for the machine operates urban supply water or your own water efficiently.
  • Page 37 UPPER IMPELLER CEILING IMPELLER Check if the holes on the upper (MODEL DEPENDING) impeller (1) are clogged. If they Check if the holes on the top ceiling are clogged, remove and clean the impeller (1) of your machine are impeller. Turn its nut to left to remove clogged.
  • Page 38: Troubleshooting

    11. TROUBLESHOOTING Machine does not start. Power cable is unplugged. >>> Check if the power cable is plugged in. • Fuse is blown. >>> Check the fuses in your house. • Water is cut. >>> Make sure that the water inlet tap is open. •...
  • Page 39 door and wait for evacuation of the steam inside for a while. Unload the dishes after the pieces cool down to a touchable level. Start unloading process from the lower basket. Thus, dropping of water remained on a piece at upper basket onto the pieces at lower basket is prevented. Selected programme is unsuitable.
  • Page 40 There is a different odour in the machine A new machine has a peculiar odour. It will fade out after a couple of washing. Filters are clogged. >>> Check if the filter system is clean. Clean the filter • system regularly as illustrated in section “Cleaning and Care”. Dirty dishes are kept in dishwasher for 2-3 days.
  • Page 41 Detergent remains in detergent dispenser. Detergent dispenser was damp when adding detergent. >>> Make sure that • the detergent dispenser is dried well prior to filling it with detergent. Detergent is added long before the washing process. >>> Pay attention to •...
  • Page 42 A smear remains on glasses that resembles milk stain which can not be removed when wiped by hand. A bluish / rainbow appearance occurs when the glass is pointed to light. Excessive rinse aid is used. >>>Lower rinse aid setting. Clean the spilled •...
  • Page 43: Technical Features

    If you cannot eliminate the problem although you follow the instructions in this section, consult your dealer or the Authorised Service Agent. Never try to repair a nonfunctional product yourself. 12. TECHNICAL FEATURES Load capacity 14 place settings Permissible water 4.35 - 145 psi (0.3 - 10 bars) pressure Electrical connection...
  • Page 44: Warranty Statement For The Blomberg Dishwashers

    1 year * limited warranty from date of components. The dishwasher must have been used under normal first installation Blomberg will repair or replace at no household conditions and not cost to the consumer any defective commercially (Labor charges are the...
  • Page 45 PARTICULAR PURPOSE FOR Blomberg may, at its option, also replace the whole dishwasher with WHICH YOU MAY BE BUYING THIS the same and/or equivalent model PRODUCT, EXCEPT AS OTHERWISE PROVIDED IN THIS WARRANTY with equal or better functionality if the original model is no longer available.
  • Page 46: How To Get Service

    Please contact the Distributor for your State or Province as listed on the Distributor Contact List, or call our Toll Free Number at 1 800 459 9848 for direction to an Authorized Blomberg Service Agent. Document Number : 15 0595 01 00_AA_BLOMBERG_D1_USA/ 15-02-16.(15:22)
  • Page 47 www.blomberginternational.com info@blomberginternational.com...

Table of Contents