Table of Contents

Advertisement

Cirrus Truck Camper Manual
800 MODEL
March 2016

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the cirrus truck camper 800 and is the answer not in the manual?

Questions and answers

Summary of Contents for Little Guy cirrus truck camper 800

  • Page 1 Cirrus Truck Camper Manual 800 MODEL March 2016...
  • Page 2: Table Of Contents

    Table of Contents Smoke Detector Carbon Monoxide Gas Safety Precautions Carbon Monoxide & Propane Detectors Welcome Emergency Window Exit Operation Limited Warranty Backup Camera Coverage Provided Electrical & LP Operation Manufacturers Information Component Manufacturers On The Road Owner’s Obligation Loading Exclusions from This Warranty Storage Preparing for Travel...
  • Page 3 Battery and Compartment Water Pump Battery Terminology Fresh Water Battery Information Water Tank Fill Battery Storage Precautions City Water Connection Battery Charging Water System Drain Battery Separator Sanitizing Fresh Water System Battery Disconnect Switch Water Filter System Monitor Panel Shower Water Heater Ignition Switch Exterior Wash Station (Shower) Exterior Light Fuse Box...
  • Page 4 Short-Term Storage Long-Term Storage Storage Below Freezing Winterizing Method Water Heater Bypass Reactivating Camper After Storage Outside Area 12-Volt System 120-Volt System Fresh Water System Propane System General Maintenance Camper Loading & Checking Typical Bulbs & Fuses Exterior Sealant Chart Schematics Suppliers Service Phone &...
  • Page 5: Limited Warranty

    Limited Warranty Pleasant Valley warrants to the original end user purchaser (“Owner”) of this truck camper (“Camper”) to be free of defects in materials and workmanship and for structural integrity, under normal use, with reasonable care and maintenance, for one (1) year from the date of purchase (the “Warranty Period”), subject to the exclusions given below.
  • Page 6: Dealer Responsibilities

    Dealers Responsibilities 1) The dealership is responsible for inspecting both factory and dealer installed components for proper operation. This is known as the Pre-Delivery Inspection and Systems Check. This will assure you that all components are in proper working order and free of defects prior to you taking delivery.
  • Page 7: Pre-Delivery Inspection/Warranty Registry Form

    Pre-Delivery/Warranty Registry Form Customer Relations Information...
  • Page 8: Safety & Identification

    Safety and Identification Your safety, and the safety of others, is very important. Operating your truck and camper is an important responsibility. As you read this manual, statements preceded by the following words are of special significance: Indicates a potentially hazardous situation which, if not avoided, may result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in damage to the component, camper or your truck.
  • Page 9 All pilot lights, appliances and their ignitors (see operating instructions) shall be turned off before refueling of motor fuel. Tanks and/or propane containers. Failure to comply could result in death or serious injury. If you smell gas:  Extinguish any open flames, pilot lights and all smoking materials. ...
  • Page 10 Fire Safety Fire safety is an important part of owning a truck camper. The following basic rules of fire prevention can help eliminate the possibility of a fire. 1) Never store flammable liquids inside the truck camper. 2) Never leave cooking food unattended. 3) Never smoke in bed and always use an ashtray.
  • Page 11: Identifying Your Camper And Its Components

    Identifying Your Camper and Its Components For identification purposes it is recommended that you write the camper serial number inside your camper. Pick a spot behind a drawer or inside a cabinet. Protect yourself from possible theft and be able to identify your property. You should keep a copy of this information at home.
  • Page 12: Information About This Manual

    Information About This Manual This Owner’s Manual is of a general nature only and does not cover every aspect of all models manufactured by Pleasant Valley. Each owner should read this manual thoroughly and heed the warnings given herein, as well as those warnings given in the component instruction manuals contained in the Owner’s Information Package.
  • Page 13: Camper And Truck, Weighing, Loading

    Camper and Truck, Weighing, Loading Matching Camper and Truck Selecting the right combination requires understanding a few guidelines. Your Pleasant Valley dealer can be a valuable source of information when matching a camper to your truck. The truck bed is mounted to the frame of the truck with mounts that allow for some movement. It is important to allow enough clearance between your truck and camper to prevent damage due to normal racking, twisting and bouncing during driving conditions.
  • Page 14: Weighing Your Truck & Camper

    Driving on under-inflated tires can cause the tires to overheat, which leads to the breakdown of the tire’s internal structure. Improper inflation also can reduce your ability to control your vehicle. Tire blowouts occur more during summer months than any other time of the year.
  • Page 15 UVW (Unloaded Vehicle Weight) – the weight of the camper as manufactured. If applicable, it also includes full generator fluids including fuel, engine oil and coolants. CCC (Cargo Carrying Capacity) – equal to GVWR minus each of the following:  ...
  • Page 16: Attaching Camper To/Removing From Truck

    Failure to properly match camper and truck can result in undesirable handling characteristics and create a safety hazard. In addition to knowing the overall weight that can be safely loaded in or attached to the truck, you should know how to distribute the weight in the camper so that correct amounts of weight are placed on each truck axle.
  • Page 17 Safety Tips: 1) Never allow the camper to be occupied while it is being loaded or unloaded. 2) Never raise the rear of the camper higher than the front of the camper. 3) Be sure all tie-down devices and electrical devices are disconnected from the vehicle. 4) Do not load the camper on a windy day.
  • Page 18 Do not use the electric jacks to raise or lower the camper using only 120-volt power. The converter’s charger will be damaged if the jacks are operated with 120-volt power through the 12-volt converter without a 12-volt battery installed in the camper. Before operating the remote control electric camper jacks, be sure to read and understand the operating instructions that were provided with your camper pertaining to their safe operation.
  • Page 19 The receiver uses 8-25 amp fuses that protect each of the jack circuits. If any of the jacks do not operate while depressing the “All Jacks” button on the remote, check the fuses. Jack Fuse Panel Location This panel is located inside storage door #2 To Lift Camper: (Extend jacks to ground) 1) Press and hold the ‘All Jacks’...
  • Page 20: Support Equipment

     You are within range for the remote to operate.  Adequate 12-volt battery power is still available.  The jack electrical cord is securely plugged into the exterior socket.  Hold the remote vertically (keypad facing you) and have it between the camper and you. ...
  • Page 21: Hitching And Towing System

    Hitching and Towing Systems A Torklift hitch system is recommended for use when towing with your truck and Pleasant Valley camper. The Super Hitch Receiver, along with a custom designed bar extension for campers over 8’ are available from authorized Torklift Dealers. It can be used with a standard weight carrying ball mount, or for added capacity, a weight distributing hitch bar and ball mount.
  • Page 22: Effects Of Prolonged Occupancy

    Effects of Prolonged Occupancy Condensation & Humidity Your camper was designed primarily for recreational use and short-term occupancy. If you expect to occupy the camper for an extended period, be prepared to deal with condensation and the humid conditions that may be encountered. The relatively small volume of space and air tight construction of a modern recreational vehicle means that the normal living activities of even a few occupants will lead to rapid moisture saturation of the air contained in the camper and the appearance of visible moisture, especially in cold weather.
  • Page 23: Dripping Ceiling Vents

    Minimize moisture release inside the camper. Run the bath vent fan (or open the bath vent) when bathing to carry water vapor out of the camper. Avoid making steam from excessive boiling or use of hot water. Remove water or snow from shoes before entering to avoid soaking the floor.
  • Page 24: Fire Extinguishers

    Fire Extinguishers The fire extinguisher in your camper is located near the main entry door. Your fire extinguisher should be replaced immediately after use or discharge. The fire extinguisher furnished with your camper is rated for Class B (gasoline, grease, flammable liquids) and Class C (electrical) fires since these are the most common types of fires in recreational vehicles.
  • Page 25: Carbon Monoxide Gas Safety Precautions

    Carbon Monoxide Gas Safety Precautions Carbon monoxide gas is colorless, tasteless, and odorless. It is a combustion by-product of fuel burning engines. The engines in your truck and generator system (if installed) produce it constantly while they are operating. Carbon monoxide gas is deadly. Please read and understand the following warnings and precautions to protect yourself and others from the effect of carbon monoxide gas.
  • Page 26 Do not use a cigarette lighter to test the CO/Propane gas alarm. Butane gas may damage the sensors. DO NOT attempt to test the alarm by any other means than by using the TEST/RESET button. DO NOT attempt to produce CO to the alarm.
  • Page 27: Backup Camera

    Be aware of the difference between a propane leak versus propane escaping from an unlit, open burner. Pure propane from a leaking pipe or fitting is heavier than air and will build up its heaviest concentration at the floor level first. Propane from open burners is intentionally mixed with air to induce burning and will dissipate into the air.
  • Page 28 12-volt DC system The 12-volt system provides power for the following components:  Electric Jacks  Interior Lighting  Exterior Lighting  Water Pump  Refrigerator  Alde System  Stereo/CD/DVD Player   Systems Panel Monitor  Fantastic Fan ...
  • Page 29 Battery Information The battery(s) must be securely strapped in the compartment at all times. The battery(s) is charged by the truck’s charging system while the truck is running or when connected to 120-volt power through the power converter. If equipped, the onboard generator charges the battery while running through the power converter. Check that the battery liquid level is correct (weekly in warm climate, monthly in cold climate).
  • Page 30 Battery Disconnect Switch While in storage use the battery disconnect switch to help with slowing down the discharging of the battery. System Monitor Panel The systems monitor panel may incorporate controls and instrumentation for the water and holding tank levels, battery voltage level, water pump switch. Monitor Panel –...
  • Page 31 Interior Lighting The interior lighting operates on 12-volt DC power only. When connected to a 120-volt source or using the generator, the power converter transforms 120-volts to 12-volts. However; when not connected to 120-volts, the entire load of lights, water pump, exhaust fans, etc., is on your 12-volt battery(s).
  • Page 32 Power Distribution Center The power distribution center consists of 120-volt AC, 12-volt DC and the power converter. The 120-volt AC panel board containing a 30-amp main breaker and 15 and/or 20-amp branch circuit breakers. These breakers interrupt the power if the rated current is exceeded.
  • Page 33 To stop the generator: 1) Turn off all electrical loads. 2) Let the generator run at no-load for a few minutes, to stabilize internal engine generator temperatures. 3) Place Start/Stop switch in the Stop position. Generator Operating Safety Precautions and Warnings Do not block the generator ventilating air inlets or outlets.
  • Page 34 Propane Gas Safety Please observe the warnings and cautions contained in this section as well as the manufacturers supplied information with each gas appliance. Propane is stored in a high-pressure tank in liquid form and is delivered to the appliances in a gaseous form. The propane canister(s) must not be placed or stored inside a vehicle.
  • Page 35 Turn off main propane valve and individually turn off all propane appliances or electrically disconnect automatic ignition appliances before entering propane bulk plant or motor fuel service station. When not individually turned off, automatic ignition appliances may continue to spark. Do not fill propane containers to more than 80% capacity.
  • Page 36  You can die or receive brain damage from Carbon Monoxide.  Make certain the exhaust from Propane appliances is directed to the outdoors.  Have a working carbon monoxide detector in the accommodation spaces of your trailer before operating Propane gas appliance.
  • Page 37: On The Road

     Risk of fire or explosion.  Never us a flame, heat lamp or hair dryer to thaw a Propane gas regulator.  Use an incandescent light bulb to warm the regulator.  Do not remove the regulator cover or attempt to service the Propane gas regulator. On The Road Loading When loading camper gear, store heavy items first and place down low.
  • Page 38: Post-Trip Clean-Up

    (Systems) 1) Fill fresh water tank. 2) Drain holding tanks and secure drain cap. 3) Check operation of interior lights and appliances. 4) Check propane gas level. Check for kinked propane lines and possible leaks. Post-Trip Clean-Up 1) Clean unit and check for damage. 2) Drain waste-holding tanks.
  • Page 39: Equipment

    Equipment Some features described here do not appear on all Pleasant Valley models. Pleasant Valley is continuously changing and upgrading appliances for better usage and for your convenience. For that reason, the style you have may not be exactly what is described in this manual.
  • Page 40: Skylight

    Skylight This skylight is dual pane and opens. It has a sliding screen. To open; Depress the button on the latches and turn to open. And tighten knobs on the window stays. To close; Loosen the window stay knob, close and latch. The shade and screen operate independently of each other and are engaged by connecting to each other and sliding.
  • Page 41 Ladder It is critical that all racks and accessories be properly and securely attached to your camper. Improper attachment could result in an accident or damage to your camper’s roof. Check the attachments prior to use and periodically inspect for adjustments, wear and damage. Large, long or oversize items will require additional strapping/tie downs.
  • Page 42: Awning

     5 shore beeps – Error/Wrong code  Short set of tones after your input your code and before the dead bolt extends signifies that the batteries are getting low and will need to be changed soon. - Code can be between 0 and 8 digits long, we recommend at least 4 digits for security. New Code: _____ _____ _____ _____ _____ _____ _____ _____ Syncing the RV Lock handle with your optional RV Lock Remote(s) Turn the FOB switch to “on”...
  • Page 43 Cab over Area Do not allow anyone, children especially, to ride in the cab over area while traveling. Any sudden stops could result in injury. Dinette Conversion To convert the dinette area into a sleeping area:  Locate the table locking lever hardware located on the underside of the table. ...
  • Page 44 The refrigerator operates on 120-volt AC power, propane and/or 12-volt DC. The operating instructions supplied in the Owner’s Information Package will help you with detailed information from the manufacturer. The recreational vehicle propane type refrigerator operates on the “absorption” principle and therefore must be reasonably level. When your camper is stationary, it should be leveled for comfortable living.
  • Page 45 Do not turn the burner control knobs ON, allowing gas to escape before lighting a match or using an electronic igniting device. To Bleed Air from Line  Hold a lighted match next to the burner.  Turn the surface burner control know to the LITE position. ...
  • Page 46 Mixing Valve When you’re setting up the heater for the first time you will want to test the water temperature coming out of the faucet and adjust it by using the Mixing valve located close to the Alde unit this adds cold water to hot water before it gets to the faucet to avoid getting water burns.
  • Page 47 Experience has shown that some RV parks may experience reduced power (low voltage) on days with high heat or humidity, commonly referred to as a “brown out”. This condition may result in the air conditioner circuit breaker tripping in your power distribution center.
  • Page 48: Fresh Water System

    Fresh Water System Your Camper is outfitted with a system designed to provide fresh (potable) water service from an onboard water tank or a city water connection with a fresh water tank fill located on the roadside of the camper. When connecting to the city water hookup, use only a non-toxic water hose, available at most RV supply stores.
  • Page 49 Filling the fresh water tank: 1) Make fresh water tank drain valve is closed, located in the compartment door #3 2) Remove cap on fresh water fill inlet. 3) Using a 3/8 hose adapter, fill the water tank through the exterior fill spout slowly at a low volume until water overflows out of the vent or check tank monitor and fill until it reads 100%.
  • Page 50: Exterior Wash Station

    Water Filter An in-line water filter attached to the inlet side of the water pump filters dirt, mineral scale, or organic matter out of the fresh water system. If you suspect a clogged filter, it is easily removed and cleaned. Loosen the clear filter cap at the inlet end of the filter. Flush out and clean screen.
  • Page 51: Bathroom

    This holding tank must be primed with 2 gallons of water and one odor control chemical package at each initial use. Add more odor control chemical if needed until dumping is required. Refer to the chemical package available at most RV outlets for specific instructions.
  • Page 52 7) Pull the handle for the grey water holding tank. Repeat steps 4 through 6. This tank is dumped last to aid in flushing the drain hose. 8) Remove the sewer hose and replace the outlet cap. 9) Rinse out the sewer hose with fresh water and remove the sewer hose from the dump station. 10) Replace sewer or dump station cover(s).
  • Page 53: Short-Term Storage

    Short-Term Storage (less than 45 days – Above Freezing) 1) Wash the exterior. 2) Park the camper as level as possible front to rear and side to side. 3) Before disconnecting the battery cables, check the charge in the battery. Recharge as necessary. Clean terminals, top and sides of battery and battery box.
  • Page 54: Water Heater Bypass

    Alde Relieve Valve Fresh Water Drain Valve Water Pump hoses Draining the water system alone will not provide adequate cold weather protection. If the camper is to be unheated during freezing temperatures, consult your dealer for the best winterizing procedure for your climate. Your dealer can supply you with one of the special non-toxic antifreezes that are safe and approved for use in RV water systems.
  • Page 55: 12-Volt Dc System

    NOTE: Spiders and other small insects climb into burner tube(s). The spiders create webs, build nests and lay eggs. These webs and nests can be very small, but they are very strong and can block the flow of gas. Mud Daubers are another insect to watch out for. It is not uncommon for Mud Daubers to build their mud huts in places like the furnace exhaust ports.
  • Page 56 The Maintenance Schedules specifies how often you should have your camper serviced and what things need attention. It is essential that you have your camper serviced as scheduled to retain its high level of safety and dependability. Keep accurate records of maintenance, service performed and follow all owner obligations, as required, to keep warranty in force. Exterior Maintenance Some exterior parts of your camper are made of fiberglass, metal, rubber and plastic materials.
  • Page 57 Sealant Renewal The adhesives and sealants used in the construction of your camper were developed to remain waterproof under sustained effects of weather and vibration. However, even the finest materials will eventually dry out and lose their effectiveness under the constant heat of the sun, attack by other elements and road vibration.
  • Page 58 DO NOT use Windex as it will damage the acrylic. Never use any petroleum based cleaners, or caustic chemicals on your windows/skylight vent. DO NOT use WD-40 (as it is petroleum based). Never use a razor blade, putty knife or abrasive pad to clean your windows/skylight vent.
  • Page 59 Exterior Lights Check the operation of your camper’s exterior lights prior to each trip. This should also include your truck’s lighting. An inoperative bulb or fixture can create an unsafe condition by reducing your ability to signal your intentions to other drivers. When replacing exterior bulbs, take care that the sealant around the light is not disturbed.
  • Page 60 Wood Product Care Remove dust with a clean slightly damp cloth. Buff with a soft, dry cloth. Never use harsh detergents and solvents. Fiberglass Care Do not use abrasive cleaners or scouring powders. Use of abrasive cleaners will dull or damage the surface of this product and could leave scratches.
  • Page 61 Maintenance Chart 1 Before Use Service to Be Performed Each Trip At Set-Up & Monthly Weekly Inspect wiring, connector plug and receptacles Check exterior lighting Inspect & tighten mounting bolts on each jack corner Inspect & secure camper anchors Test propane leak detector for proper operation Test carbon monoxide detector for proper operation Test smoke detector for proper operation Inspect generator exhaust muffler &...
  • Page 62 Maintenance / Repair Schedule Date Maintenance/Service Procedure Service Center Name/Address/Phone...
  • Page 63: Camper Loading & Checking

    Camper Loading & Checking 1) Load the camper onto the truck following the procedure in the “Loading and Unloading” section. 2) Check the operation of taillights, turn signals, backup lights, clearance lights, license plate lights, and emergency flashers. Your camper should now be ready for a new traveling season. If you choose, your Pleasant Valley Dealer can double check your preparation and correct any defects or make any necessary adjustments.

Table of Contents