Gruppo Norton MSC 800 Installation And Maintenance Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Automatismi per Aperture

FCM

FCE

800

Gruppo Norton S.r.l.

capitale sociale 100.000 i.v.

partita i.v.a. 05636180829

S.r.l.

2000

Via Galileo Galilei s.n. Zona Ind.le 90044 Carini (PA) (vicino DHL)

tel. +39 091 8816371 - tel./fax +39 091 8816505

e-mail: automatismi@grupponortonsrl.191.it

S.r.l.

Manual for installation

and maintenance of

ENG

automatisms for sliding

gates.

FCM

FCE

Table of Contents

Need help?

Do you have a question about the MSC 800 and is the answer not in the manual?

Questions and answers

Summary of Contents for Gruppo Norton MSC 800

Page 1 Manual for installation and maintenance of automatisms for sliding gates. 2000 Gruppo Norton S.r.l. Via Galileo Galilei s.n. Zona Ind.le 90044 Carini (PA) (vicino DHL) capitale sociale 100.000 i.v. tel. +39 091 8816371 - tel./fax +39 091 8816505 partita i.v.a. 05636180829 e-mail: automatismi@grupponortonsrl.191.it...
Page 2 21) Do not allow children or adults to stay near the observed, in addition to national legal regulations. product while it is operating. 9) Gruppo Norton is not responsible for failure to 22) Keep radiocontrols or other pulse generators away observe Good Technique in the construction of the...
Page 3 MOTOR MSC 800 - MSC 2000 These instructions apply to the following models: MSC 800 where: FCE, MSC 800 FCM, MSC 2000 FCE e MSC 2000 FCM. Ta = opening time The automatisms MSC 800 - MSC 2000 gearmotor is an...
Page 4 2. ELECTRICAL SET-UP (standard system) Fig. 3 1) Motor MSC 800 / MSC 2000 2) Photocells Fig. 4 3) Key selector 4) Flashing lamp 5) Radio receiver Fig. 2 3. INSTALLING THE AUTOMATISM 3.1. Preliminary checks To ensure safety and efficiency of the automated system,...
Page 5 NOTES ON RACK INSTALLATION 3.4. ASSEMBLING THE RACK • Make sure that, during the gate travel, all the rack elements 3.4.1. STEEL RACK TO WELD (fig.7) do not exit the pinion. • Do not, on any account, weld the rack elements either to the 1) Fit the three threaded pawls on the rack element, spacers or to each other.(only for steel rack).
Page 6 4.3. AUTOMATISM SYSTEM TEST Once installation of the operator has been completed, make a careful functional check of all accessories and safety devices connected. Give the Client the “User Guide” and demonstrate the correct operation and use of the gearmotor, highlighting the potentially dangerous zones of the automated system.
Page 7 Via Galileo Galilei - Z.I. 90044 Carini (Pa) - Italy Declares that: The motor for sliding gate mod. MSC 800, mod. MSC 2000 • is made to be integrated into a machine or to be assembled with other machinery to create a machine under the provisions of Directive 89/ 392 CEE, and integrated 91/368/CEE, 93/44/CEE, 93/68/CEE;...
Page 8 MSC 800 - MSC 2000 SPARE PARTS 1 Body reducer Bearing 6303 Crankshaft Bearing 6303 Motor cover Screw TCEI 6 x 12 Register clutch cap Electronic box hinge Support spring limit switch Limit switch box base Limit switch cover Electric box base...