FAST ČR, a.s., Černokostelecká 1621, 251 01 Říčany, Czech Republic; FAST ČR, a.s., Cejl 31, 602 00 Brno, Czech Republic; FAST PLUS, Na Pántoch 18, 831 06 Bratislava, Slovakia; www.sencor.cz • Protect the device and the remote control against rain, spray or contact with any other liquid, do not leave or install the device outdoors.
Page 6
• When the device is moved from a cold to a warm environment or vice versa, e.g. when using the device in a very humid environment, air humidity may condense on some parts inside the case of the device, namely on the sensing system and the player may temporarily stop functioning.
1 Front panel, rear panel and connection Front panel 1. Main switch Rear panel 1. ANT IN - Aerial input 2. TO TV - To connect ot TV set by coaxial cable 3. TV - SCART to connect to TV set 4.
2 Remote control Switch between operation and standby modes Press to temporarily cut off the sound Enter number or select a channel number to watch TV/R Switch between TV and Radio mode To switch AV mode on or off for the TV. It allows you to view an analogue channel on your TV whilst recording a digital channel for your receiver.
3 Welcome Page 1 When fi rst time power on, it will show welcome page 2. Press [Up/Down] key to move highlight. 3. Press [Left/Right] key to select region and OSD language. 4. Move highlight to [OK] button and press [ENTER] key to begin to auto scan. 5.
4 Main Menu When you press [Menu] key, you can enter main menu. There will display the picture like below: 1. Press [left/right] key to select menu pages among Channel, Installation, Setup and Tools. 2. Press [OK] key to enter the selected item 5 Channel 1.
5.1 TV Channel List When you enter to “Channel List” menu, 1. You can move highlight by press [Up/Down] key to preview the current highlighted program in the right side preview window. 2. You can press [REV/FWD] key to implement the Page Up/Page Down function. 3.
Page 12
5. Press [REV]or [FWD] to page 6. Press [Menu] or [Exit] to exit. Select 1. Press [OK] key to select the highlighted channel. Press [OK] again to cancel the selection. Select All 1. Press number [0] key to select all channel. Press number [0] again to cancel all selection.
Page 13
Favorite 1. Press number [1] key to set the favorite channel. It will display “Group” box for you to select group (group 1~8). Press [Up] or [Down] key to move the highlight, and press [OK] to select the favorite group. It will ask you “Assign channel to Group N. Are you sure?”...
Page 14
Skip 1. Pressing number [3] key, it will ask you “Are you sure to save?” Select “Yes” to make a skip mark and select “No” to cancel the operation. 2. When highlight on the skip channel, press number [3] key again can cancel the skip mark.
Rename 1. Pressing number [5] key, it will show a “Rename” window and you can rename the highlighted channel. 2. Press [Up][Down][Left][Right] key to move the highlight in “Rename” window. Press [OK] to input char. 3. Move the highlight to “OK” and press [OK] key to save the modifi cation. 4.
5.1.3 Sort 1. Press number [3] key to sort channel. 2. It will display a dialogue to confi rm. If you select “Yes”, it will display “Sort” box. 3. Press [Up] or [Right] key to move the highlight and press [OK] to select sort type such as Default/Name(A-Z)/Name(Z-A)/FTA/Lock.
5.2 Radio Channel List Basically, the operation of “Radio Channel List” is same as “TV Channel List”, but there is one point different: In “Radio Channel List” mode, there is no video information, so it will always display Radio’s logo in the right side preview window. 5.3 Delete All Favorites This operation will remove all favorite channels (includes TV and radio favorite channels) from favorite list.
6.1 Auto Scan When you enter to “Auto Scan” menu, there will display the screen like below: (If channel lock is “On”, input password fi rst. Default password is “0000”) 1. Firstly please select the country in System Setup Menu/Region and Time/Region, such as “France”.
When scan band is VHF and region is “France”, the range of Ch No. is from 1 to 9. (it’s according to region) 3. When you complete your modifi cation, move highlight to “Search” item and press [OK] key, then it will begin to scan. 4.
Press [Up/Down] key to select menu items among each item. Press [OK] key to enter the selected item. 7.1 OSD Language When you enter to “Language” menu, you will see the screen like below: 1. OSD Language: Press [Left], [Right] key to change the osd language. 2.
3. Video Output is use for switching the video output mode. Now we provide below options: CVBS+RGB, CVBS+S-Video,. You can press [Left/Right] key to select each mode circularly. 4. LCN Mode can control the channel whether sort by the sequence information in the streams.
7.4 Timer Setting When you input to “Timer Setting” menu, you will see a screen like below: 7.4.1 Program Timer When you enter “Program Timer”, you will see the window like below: 1. Current time information will display on the fi rst row; if the current time is incorrect, please modify the time information in “Time”...
6. Time: press [OK] key and number keys to input your wakeup time. Once the time’s up, no matter what the system is in standby mode or in playing mode, the system will automatically switch to the channel you want and start to play. 7.
7.5 OSD Setting When you input to “OSD Setting” menu, you will see a screen like below: 1. Subtitle Display: You can press [Left/Right] key to select “On” or “Off”. If the current channel has subtitle information, it will be showed up while this function is “On”. If this function is “Off”, there won’t show up subtitle information even if the current channel has subtitle information.
Page 25
2. Menu Lock determining that when user wishes to enter “Installation” menu and “Chan- nel List/Edit/Del all/Auto scan/channel scan/Load default/upgrade”, whether have to input Password or not. If the setting of “Menu Lock” is “ON” which means user have to key in password, set “OFF”...
After fi nish saving and draw back to “System Setup” menu, the revising is complete. 5. Press [Exit] key to draw back from the “Parental Lock” menu. 8 Tools In “Tools” menu: 1. Press [Up/Down] key to select menu items among each item. 2.
2 Snake ● Moving highlight to “Setup” and press [Left/Right] key to select the game level (speed). ● Moving highlight to “Start” and press [OK] key to start the game. ● Moving highlight to [Cancel] keys and press [OK] key to draw back from the game. ●...
8.4 Software Upgrade When you enter to “Software Upgrade” menu, you will see the window as below: 8.4.1 Upgrade By RS-232 1. Transfer Mode:P2P/P2M. P2P means one STB upgrade the other one. P2M means one STB upgrade several other boxes at same time. 2.
5. When connectting the master and multi slavers, you can move highlight to “Start” on master reeciver and press [OK] key to start. Turn on all slavers receiver and press [OK] again on master to begin to upgrade. 6. Press [Exit] key to save the parameters and draw back. 8.4.2 Upgrade By Air This function can upgrade the software through signal lines from the cable.
9 Hotkey 9.1 Standby 1. Press [Power] Key can enter the Standby state 2. In Standby state, press [Power] Key again can call back the unit and go on play the previous channel 3. User can also disconnect the device’s main power to end the Standby state. 9.2 CH+/CH Infull screen, press [Up/Down] to change channel.
2. You can move highlight by press [Up/Down] key and switching each selection by press [Left/Right] key 3. Press [Exit] key to exit. 9.8 EPG 1. The STB has an Electronic Program Guide (EPG) to help you navigate channels through all the possible viewing options. The EPG supplies information such as chan- nel listings and starting and ending times for all available programs.
6. Press number key [3] in EPG screen can see the current program detail information. 7. In schedule list press [OK] key list to book program . 8. In schedule list press [REC] key to record booking program. And REC icon is showing. Default record time is 2 hours 9.
9.15 Information 1. In full screen, press [Info] key can open information bar. When information display, press [Info] key again, then it will shows the parameters of current channel. It show screen like below: 9.16 Subtitle 1. Press [Subtitle] key in full screen, it can show a “Subtitle Display” window. 2.
9.17 TEXT 1. Press [TEXT] key can see teletext information if the channel has. 2. If the channel don’t have teletext, it will display “No Teletext Data. 9.18 Sleep 1. You can set sleep time by press [Sleep] key in full screen. 2.
10.1 Media player Press [OK] key to enter. you will see a screen like below: 1. Press [up/down] key to moving highlight in fi le list; 2. Press [left/right] key to moving highlight to switch fi le list and bottom button. 3.
10.1.1 Music Press [OK] key to playing current music, the screen like below: 1. Press color key [red] one time to go to last music fi le. 2. Press color key [red] 3s to fast backward mode. 3. Press color key [green] one time to go to next music fi le. 4.
10.1.2 Image When the highlight on image fi le, it will show image in preview window and show infor- mation below the preview window is for displaying current fi le name, picture size. The screen like below: When the highlight on image fi le, press [OK] key to play current image in full screen: 1.
10.1.3 Mpeg Press [OK] key to playing current fi le in full screen, you will see a screen like below: 1. Press [info] key to show/hide navigator bar. 2. Press [Play] key or number key [1] to start playing current fi le from pause mode or stop mode.
10.1.4 Bottom buttons You can press [left/right] key to moving highlight to 5 bottom buttons, about: Imglist: Press [FAV] or number key [2] in fi le list to add favor image fi les to Image list. ● Press [OK] key then system default slide show pictures by repeating image list fi les ●...
Page 40
● Press [up/down] key to moving highlight. ● Press color key [red] to start play fi les in image list. ● Press color key [yellow] to delete fi le one by one from image list. ● Press color key [blue] to delete all image fi les in list. ●...
Page 41
● Fate effect: For setting the slide show’s picture fade in fade out effect. It has “Shutter”, “Chessboard”, “insert”, “Left-UP stretch”, “Random”, “Cross Fade”. Sort Press [OK] key to enter “Sort menu”, you will see the screen like below: ● Name(A ~ Z): sort fi les by fi les name’s 1st letter from A to Z; ●...
Select “Yes”, enter “USB media player”; select “No” keep to TV mode. 2. When user exit USB media player menu, system will prompt user that “do you want to save current temp play list to USB disk?”, there’s a “Yes” and “No” button on prompt window.
10.2.3 Rename ● Press number key [3], it will show a “Rename” window and you can rename the high- lighted fi le. ● Press [Up][Down][Left][Right] key to move the highlight in “Rename” window. Press [OK] key to input char. ● Move the highlight to “OK” and press [OK] key to save the modifi cation. ●...
10.4 DVR Confi guration Press [OK] key to enter, you well see a screen like below: 10.4.1 Timeshift To user switching timeshift mode, press [left/right] key to select “ON/OFF” 10.4.2 Timeshift Time(min): Manual to change how many space system allocated for timeshift buffer. It have:10/20/30/40/50/60 (min) to select.
10.5 Safely Remove Storage Device 8. It’s to safely remove your inserted USB device like on computer. Select this item and press OK, system will un-mount all storage devices inserted on this system. 11 DVR 11.1 REC(Record) 1. Press [record] key to record a fi le in TV full screen, and show a REC bar on screen. The Screen like below: 2.
Page 46
4. When recording, you will press [REV/FWD] key into fast rewind mode and fast forward mode. 5. Press [stop] key to stop recording. and save a fi le in “record manage” menu. When press [Stop] key it will show a box: 6.
11.2 Timeshift Timeshift: is the recording of programming to a storage medium to be viewed or listened to at a time more convenient to the consumer. ● If insert Storage Device, and Device speed is enough, It will automatically start to time- shift, Press [pause][slow][Fast Rewind][Fast forward] key will active the timeshift bar.
Page 49
Handling instructions for the disposal of used packaging material Dispose of the packaging material in the designated place for waste disposal. Electronic and electric appliance disposal instructions Information for users for the disposal of electric and electronic devices This symbol on products or original documents means that used electric or electro- nic products must not be added to standard communal waste.