Husky HDT132 Operating Instructions Manual

See Warranty on page 8 for important information about commercial use of this product.
Operating Instructions
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or prop-
erty damage! Retain instructions for future reference.
Description
The Cleaning Gun uses compressed air
to spray water or a mixture of water
and degreaser. Use this gun to remove
grease and dirt from the engine and
engine area.

Safety Guidelines

This manual contains information that is
very important to know and understand.
This information is provided for SAFETY
and to PREVENT EQUIPMENT PROB-
LEMS. To help recognize this informa-
tion, observe the following symbols.
Danger indicates
DANGER
!
an imminently haz-
ardous situation which, if not avoided,
WILL result in death or serious injury.
Warning indicates
WARNING
!
a potentially haz-
ardous situation which, if not avoided,
COULD result in death or serious injury.
Caution indicates a
CAUTION
!
potentially haz-
ardous situation which, if not avoided,
MAY result in minor or moderate injury.
Notice indicates
NOTICE
important informa-
tion, that if not followed, may cause
damage to equipment.
Unpacking
After unpacking the product, inspect
carefully for any damage that may
have occurred during transit. Make
sure to tighten fittings, bolts, etc.,
before putting unit into service.
Do not operate
WARNING
!
tool if damaged
during shipping, handling or use.
Damage could result in bursting and
cause injury or property damage.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2002
Cleaning Gun
General Safety
Information
Read all manuals included
with this product carefully.
Be thoroughly familiar
with the controls and the
proper use of the equip-
ment.
DANGER
!
Do not spray flammable
materials, acids, corrosive
materials, toxic chemicals,
chloride compounds, fertil-
izers or pesticides. Use of these materi-
als could result in serious injury or
death.
Safety
WARNING
!
glasses
must be worn during oper-
ation.
Never aim or spray
WARNING
!
at yourself or any-
one else or serious injury could occur.
Always wear eye protection.
Release all pres-
WARNING
!
sure from the sys-
tem before ATTEMPTING TO install,
service, relocate or perform any
maintenance.
Never carry a tool
WARNING
!
by the hose or pull
the hose to move the tool or a com-
pressor. Keep hoses away from heat,
oil and sharp edges. Replace any hose
that is damaged, weak or worn.
Do not exceed the
CAUTION
!
maximum operat-
ing pressure of the air tool (90 PSI).
Never use cleaning
CAUTION
!
gun on a hot
engine. Always allow engine time to
cool.
1. Use water soluble, biodegradable
solutions in the cleaning gun.
2. Observe all manufacturer's safety
precautions for the products being
used. Always follow the manufac-
turer's directions for mixing the
product with water in proper pro-
portions. Refer to cleaning solution
MANUAL
Material Safety Data Sheet (MSDS).
3. Do not depress trigger when con-
necting the air supply hose.
4. Protect air lines from damage or
puncture. Check air hoses for weak
or worn condition before each use.
Make sure all connections are
secure.
5. Always use a pressure regulator on
the air supply to the cleaning gun.
Do not exceed any pressure rating
of any component in the system.
6. Do not spray solutions that will
remove or discolor paint.
7. Thoroughly flush the cleaning gun
with water to remove any solu-
tions.
8. Keep all nuts, bolts and screws tight
and ensure equipment is in safe
working condition.
9. Keep visitors away and NEVER
allow children or pets in the work
area.
10. Do not eat, drink or smoke when
spraying.
11. Follow all local electrical and safety
codes; and in the United States, the
National Electrical Codes (NEC) and
Occupational Safety and Health Act
(OSHA).
Model HDT132
IN285000AV 11/02