Summary of Contents for DOG d–control professional 1000
- Page 1 d–control professional 1000 Electronic training collar d–control professional 1002 Electronic training collar set for two dogs User guide...
- Page 2 Declaration of Conformity VNT electronics s.r.o. Smetanovo namesti 104 570 01, Litomysl IČO: 64793826 declare under own responsibility that the product: Electronic training collar Dogtrace d-control professional 1000 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC from 9.
-
Page 3: Important Notice
The collar should never be worn for more than 12 hours a day. Long-term effect ■ of contact points on the dog’s skin can cause skin irritation. If a rash or sore skin is found, do not use the collar until it has healed. -
Page 4: Table Of Contents
Contents Important notice ............. . . 3 ECMA . -
Page 5: Introduction
cy. -
Page 6: Product Description
Product description Transmitter: integrated antenna function buttons A1 /A2 - dog A function buttons B1 / B2 – dog B LCD - display target (round red indicator) indicating where the magnetic switch is located button for power ON/OFF (long press),... - Page 7 A1 or B1 9 - command indicator of function buttons A2 or B2 10 - transmission indicator 11 - display indicator setting for the dog A or B 12 - battery power indicator 13 - indicator of mode or stimulation level...
-
Page 8: Transmitter Preparation
LCD (first line for buttons A1 / B1, second line for buttons A2 / B2). Buttons A1 / A2 are designed for a dog A and buttons B1 / B2 are designed for a dog B. -
Page 9: Receiver Preparation
3. Command setting – by pressing down button you can choose a command for the selected function button A1 / A2 / B1/ B2. Selected command will be sent to the receiver collar. You can select following commands: long discontinuous stimulation impulse ■... -
Page 10: Switching The Receiver On / Off
Switching the receiver ON / OFF To turn the receiver ON / OFF ( or for programming the transmitter with the receiver) is used a magnetic switch, marked with the red target on the receiver. Switching ON 1. Move the red target of the transmitter towards the receiver so it comes into the contact with the red target of the receiver. - Page 11 The transmitter is designed for training two dogs, so you can pair it with two receivers. Function buttons A1 / A2 are designed for the dog A and function buttons B1 / B2 for the dog B. Important: Before the programming make sure no one else is using his d-control professional or other products from the Dogtrace range close by.
-
Page 12: Choice Of The Contact Points
TIP: If your dog has very long hair, you can order 21 mm long contact points. When your dog has a dry skin in the area where the contact points are, it is good to lubri- cate the dog‘s skin with a vaseline, hand cream, or baby oil - which enables a correct transfer of stimulation impulses. -
Page 13: The Basics Of Using A Training Collar
■ tracking rope. Your dog will have to get used to the collar; let the dog wear the collar for a few ■ days, but do not use it so that your pet does not discover the connection with its attachment and effects. - Page 14 The transmitter also allows you to set a different interval of flashing when using two collars at the same time - you can easily spot your dogs according to the flashing interval (example: a dog A - flashes once in a second and a dog B - flashes once in two seconds).
-
Page 15: For The Best Results
This function enables you to draw an attention to sensitive dogs or dogs with a hearing malfunction. It ensures a discreet recall of the dog, which is almost impossible by deaf dogs and which can not be heard by anyone nearby. It pro- vides a possibility to disturb the dog during an unwanted activity and to use the moment of a surprise. -
Page 16: Troubleshooting
Thicker fur dog – it is necessary to tighten the collar so that the permanent ■ contact with the dog‘s skin is ensured. If the fur is too thick, it is recommended to cut the hair or choose a longer type of contact points. -
Page 17: Maintenance
Maintenance It is important to keep the device clean. Never use volatile substances eg.: thinner, gasoline or other cleaners. To clean your Dogtrace d-control use a soft, damp cloth and, if necessary, neutral detergent. The transmitter and the receiver (collar) Dogtrace d-control professional is water- proof only on condition of the good state of the seal. -
Page 18: Warranty Terms And Conditions
Warranty terms and conditions VNT electronics s.r.o. provides a 2 year warranty on the Dogtrace products with respect to defects in material and workmanship under normal use and service from the date of the original purchase. The limited warranty does not cover the following: batteries ■... - Page 19 6. It is required that all items being sent for a repair must be properly cleaned. Items deemed to be insufficiently cleaned will be returned unrepaired to the customer. Please do not include the strap or any other accessories if it is not a subject of the warranty.
-
Page 20: Certificate Of Warranty
Certificate of warranty Manufacturer: VNT electronics s.r.o. Smetanovo náměstí 104 570 01 Litomyšl Czech Republic Phone: +420 733 121 890 www.dogtrace.com Dealer: Certificate of Warranty: Serial Number: ........................Date of Sale: ........................Stamp and Signature: Copying of this user guide is strictly prohibited without the Verze 2015-9-30 / ENG prior written consent of VNT electronics Ltd.
Need help?
Do you have a question about the d–control professional 1000 and is the answer not in the manual?
Questions and answers