Advertisement
R
'
EAD THIS OWNER
S MANUAL BEFORE USE AND
RETAIN IT FOR FUTURE REFERENCE
Saw Train is a complete retrofit kit to convert your
table saw into an incredibly accurate wood
machining center. With the addition of optional
extension router tables, SmartFence® and a
fence-positioning machine, you can have one
workstation to dimension, shape, mold, joint and
dovetail - all with just one fence and one fence
machine.
The Saw Train retrofit kit consists of two cartons.
One carton contains the rails and extension table
mounting fasteners and brackets (4 brackets are
included with JST-4, 6 with JST-6 & 56, and 10 are
included with the JST-8). The second carton
contains the Sliding Bridge Assembly, SmartFence
clamping brackets, setup gauge blocks, rail-mounting fasteners,
rail end-cover plates, 48" scale and a bridge stop. T
COVERS INSTALLATION AND USE OF
MANUALS INCLUDED WITH YOUR
POSITIONING MACHINE FOR THEIR USE AND OPERATION
The Sliding Bridge Assembly and Fence brackets
are completely assembled. The fasteners required
to attach the fence brackets to the fence are
already loosely inserted in each. It is only
necessary to further loosen, engage fence T-slots
and tighten in place. The 48" scale and bridge stop
will allow you to reposition sliding bridge to make
accurate rip cuts greater than the range of your
fence machine. See Step 8.
Required tools are a Phillips screwdriver,
electric drill, 5/32" drill bit, 5/16" drill bit,
1/2" wrench and a 3/8" nut driver or wrench.
JOINTECH warrants this product from date of purchase against any defects that are due to faulty
material or workmanship. Please return the failed part only, transportation prepaid (proof of purchase
may be required) for free replacement or repair at our option. This warranty does not apply to
accessories. This warranty gives you specific legal rights that vary from state to state.
.
S
T
. R
AW
RAIN ONLY
S
F
MART
ENCE AND FENCE
.
JOINTECH LIMITED WARRANTY
Should you have any questions, contact Jointech, Incorporated.
SAW TRAIN
T
ABLE
OWNER'S MANUAL
HIS MANUAL
EFER TO THE
-
S
R
AW
ETROFIT
JST-8
JST-6
JST-4
™
K
IT
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for JoinTech SAW TRAIN
- Page 1 1/2” wrench and a 3/8” nut driver or wrench. JOINTECH LIMITED WARRANTY JOINTECH warrants this product from date of purchase against any defects that are due to faulty material or workmanship. Please return the failed part only, transportation prepaid (proof of purchase may be required) for free replacement or repair at our option.
- Page 2 SAFETY - READ ALL INSTRUCTIONS The following are important safety instructions for using the JOINTECH Saw Train. Before using Saw Train, read and follow all of the instructions and safety information in this manual. • When using the Saw Train in conjunction with •...
-
Page 3: Rail Installation
NOTE: The blade guard must be reinstalled after you have finished mounting the Saw Train rails to your table saw. A. Drill Rail Mounting Holes. Remove one of the angle brackets from the extension table hardware pack. -
Page 4: Blade Guard Adjustments
Use shorter screws for thinner tops NOTES: 1. Extension tables must be placed Fig. 5 between rails over their full length to support the Saw Train Sliding Bridge. 2. Extension Table width should not be wider than your saw. Fig. 6... - Page 5 A. Installing Table Attach a flat washer and ¼-20 hex nut to each ½” long screw. Insert nut into lower inside T-slot on inside face of rail and slide to positions necessary to support your table (Figure 7). Install a bracket onto each fastener assembly and snug in place.
- Page 6 4. SLIDING BRIDGE INSTALLATION NOTES: The Bridge length is designed to fit standard 27” to 28” table saws. The assembly is factory set for a 27” saw and will need to be adjusted to fit your particular saw. If your saw is less than 27”...
-
Page 7: Fence Installation
5. FENCE MACHINE INSTALLATION NOTE: The fastening method used will accommodate nearly any fence machine positioner or jig. To allow full positioning range of machine, you will want the front end of machine to overhang bridge platform 2 to 3 inches to provide space for the SmartFence clamping knobs and the front, fence-clamping bracket Tighten down Sliding Bridge Assembly with its front... -
Page 8: Final Alignment
NOTE: Make sure that Bridge is locked and the fence machine is in the center of its range and locked to prevent any lateral movement of carriage. B. Attach Fence Brackets Place the shims under each end of fence again. Install the Back Fence Clamp bracket under out feed end of fence engaging the ¼”... - Page 9 Your rail length then is what limits your total rip capacity unless you attach a Jointech Extension Table to right end of saw. You can achieve “tape measure” accuracy by installing the 48” scale into top of front rail (see figure 18).
-
Page 10: Maintenance
MAINTENANCE Your Saw Train is designed to give many years of virtually maintenance-free operation. An occasional cleaning is all you need to do to keep the tool in top shape. Remove the Sliding Bridge and fence from saw, invert and clean the rubber clamping pads of any dust buildup or grime. - Page 12 Jointech Building Trades and Home Shop Five Year Limited Warranty JOINTECH will repair or replace, at its expense and at its option, any part which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to the Jointech factory with proof of purchase of the product within five years and provides Jointech reasonable opportunity to verify the alleged defect by inspection.
Need help?
Do you have a question about the SAW TRAIN and is the answer not in the manual?
Questions and answers