Page 1
COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE...
CDR-205TX SPECIFICATIONS System Compact disc recorder Recording/playing time Max. 80 min (Approx., when using an 80-min disc) D/A converter Advanced Multi bit Digital filter 8 times oversampling Connections 1 analog output, 1 analog input 2 digital input (optical), 1 digital output (optical)
CDR-205TX TROUBLESHOOTING GUIDE-1 If the CDR-205TX begins to operate improperly, use the troubleshooting guide below to help you ascertain the problem. Because the unit contains a microcomputer to provide advanced functions, it may malfunction due to external noise or static electricity. If this happens, disconnect the power cord and then plug it in again after about 5 seconds.
Page 4
Eject the disc and check whether it meets (without the "FOR CONSUMER" marking) the specifications for use with the or a CD-RW has been inserted. CDR-205TX. Always insert a disc that has the markings "FOR CONSUMER" or "FOR MUSIC USE ONLY" on its surface Check Input Synchronous recording cannot be Record from a recordable source.
Page 5
R-805TX is in the energy save mode Press the power (STANDBY/ON) button on the R-805TX (If connected). to power on the CDR-205TX. No sound is The speakers are not properly Connect the speakers. output from connected.
CDR-205TX SERVICE PROCEDURES PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs a laser. Therefore, be sure to follow Laser Diode Properties carefully the instructions below when servicing. Material: GaAS/GaAlAs Wavelength: 778∼787 nm WARNING!! Emission Duration: Continuous Laser output: MAX.
CDR-205TX EXPLODED VIEW PARTS LIST REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION 27111207 Front bracket E902 27190608-1 Clamp, UA-0 V0 838130088 3TTB+8B, Self tapping screw P302 2045091012 NCFC5-091012, Flexible flat cable 27100398 Chassis P501 2045251512 NCFC5-251512, Flexible flat cable...
Page 9
CDR-205TX EXPLODED VIEWS OF MECHANISM-1 CD-R MECHANISM: DB-ALD200 From POWER PC board To MAIN PC board CD-R CORE PCB ass'y To MAIN PC board Not supplied Screw Not supplied...
CDR-205TX EXPLODED VIEWS OF MECHANISM-2 CD-R MECHANISM: DB-ALD200 • Bottom View Refer to "EXPLODED VIEWS OF MECHANISM-3" CD-R CORE PCB ass'y CN101 PARTS LIST REF. NO. PART NO. DESCRIPTION --- * LOAB ass'y Note: PDD1222 32P flexible flat cable The mechanical parts with no part number in the exploded views are not supplied.
Page 11
CDR-205TX EXPLODED VIEWS OF MECHANISM-3 CD-R MECHANISM: DB-ALD200 • Bottom View CD-R CORE PCB ass'y CN452 • How to Install the Disc Table Use nippers or other tool to cut the two sections marked A in figure 1 . While supporting the spindle motor shaft with the stopper, put spacer on top of the carriage base, and stick the disc table on top (takes about 9kg pressure).
Page 12
CDR-205TX EXPLODED VIEWS OF MECHANISM-4 CD-R MECHANISM: DB-ALD200 LOAB (ASS'Y) PARTS LIST REF. NO. PART NO. DESCRIPTION VNP1762 PC board (LOAB) CN101 S3B-PH-K KR connector, Small type S101 VSK1011 Switch CN101 S101 CD-R CORE PCB ass'y CN451 MECHA PCB (ASS'Y)
CDR-205TX BLOCK DIAGRAM Q110-2/2 P101 MJM2100M AIN R OP AMP CN501 ANALOG INPUT DACCKOUT Q110-1/2 DACLRCK LRCK MJM2100M ANALOG AIN L DACBCK OP AMP OUTPUT Q312 AK4524-VF Q211-2/2 Q211-1/2 CODEC MJM4565M MJM4565M ADCDATA SDTO AOUT L - DACDATA SDTI OP AMP...
Page 14
CDR-205TX BLOCK DIAGRAM OF MECHANISM CD-R MECHANISM: DB-ALD200 IC504 IC503 PCX1027 LC324265AT-25 VCO IC D-RAM (25P) CN502 Address Data ADLRCK ADBCK ADDATA DAMCK CD-R CORE PCB ASS'Y IC501 DALRCK PDC069A MAIN DADATA EFM ENCODER IC PC board DABCK CN501 (OP)
CDR-205TX PRINTED CIRCUIT BOARD PARTS LIST-1 MAIN CIRCUIT PC BOARD(NADG-7123-1B/-1C) CIRCUIT NO. PART NO. DESCRIPTION CIRCUIT NO. PART NO. DESCRIPTION Ceramic Resonator Q110 22240608R1 NJM2100M X710 3010242 CST5.00MGW Capacitors Q210,Q211 22241383R2 or NJM4565M-D C110,C111 393384707 47uF, 50V, Elect. 22240489R1NE MPC4570G2-T1(MST)
Page 24
CDR-205TX PRINTED CIRCUIT BOARD PARTS LIST-2 CIRCUIT NO. PART NO. DESCRIPTION CIRCUIT NO. PART NO. DESCRIPTION Transistors Plug Q902 2201275 or 2SB772-Q or CN902 25055150 NPLG-6P134 2201276 2SB772-P P901A 25055675 or NPLG-2P631 or Q903 221281 or DTC114YS or 25056028 NPLG-2P0978...
Page 25
System clock oscillation circuit output pin. (5MHz) CHECK Not used. System clock oscillation circuit input pin. (5MHz) MODE Input pin for model selection. DX-R700="H", CDR-205TX="L" IC(GND) Internal connection pin. Not used. (Connect to Ground pin) Not used. (Connect to Ground pin) Not used. (OPEN) VSS1(GND) Ground pin.
Page 26
CDR-205TX DISASSEMBLING PROCEDURES-1 CD-R MECHANISM: REPLACEMENT OF OPTICAL PICKUP The laser diode in the optical pickup block is so sensitive to static electricity, surge current and etc. That the components are liable to be broken down or its reliability remarkably deteriorated.
Page 27
CDR-205TX DISASSEMBLING PROCEDURES-2 CD-R MECHANISM: REPLACEMENT OF OPTICAL PICKUP When replacing the optical pickup, short-circuit 1, 3. Press the shaft stopper to the arrow mark direction. two terminals on the optical pickup unit. 2, 4. Pull out the shaft. Front side LD short terminals 1.
Page 28
CDR-205TX DISASSEMBLING PROCEDURES-3 CD-R MECHANISM: REPLACEMENT OF SPINDLE MOTOR When replacing the optical pickup, short-circuit Remove the CD-R CORE PCB. two terminals on the optical pickup unit. Front side LD short terminals -- Bottom view -- Disconnect the flexible flat cable and socket ass'y Unsolder the spindle motor and carriage motor.
Page 29
CDR-205TX DISASSEMBLING PROCEDURES-4 CD-R MECHANISM: REPLACEMENT OF SPINDLE MOTOR Remove the disc table ass'y. Disc table ass'y -- Top view -- Front side Remove the machine screw of two points holding the spindle motor. Machine screw -- Top view -- Front side Replace the spindle motor.
CDR-205TX ADJUSTMENT PROCEDURES-1 1. DISCS TO BE USED SERVO SYSTEM ADJUSTMENT CD: Test disc TYPE 4 YEDS-18 (by SONY) SN: 0R016 or STD-905 (by PIONEER) SN: 0R116 2. MEASUREMENT EQUIPMENT (1) Laser power meter: LE8010 (by LEADER) (2) Oscilloscope (3) CD jitter meter 3.
CDR-205TX ADJUSTMENT PROCEDURES-3 5. LD POWER ADJUSTMENT [Points] 1) LD power adjustment consists of three sessions: Playback power adjustment, CD-R record power adjustment, and CD-RW record power adjustment. 2) Once the test mode is activated in order to perform the LD power adjustment, be sure to finish the three sessions in one time, never to stop halfway;...
Page 33
CDR-205TX ADJUSTMENT PROCEDURES-4 5.3 CD-RW Record Power Adjustment Pickup objective lens Test Point RW Bias : 2.3 mW ± 0.05 mW, RW REC : 3.2 mW ± 0.05 mW, RW Erase : 5.2 mW ± 0.1 mW Adjustment Value Purpose Optimizing CD-RW recording power of laser diode.
Page 34
CDR-205TX ADJUSTMENT PROCEDURES-5 6. SERVO ADJUSTMENT AUTOMATIC ADJUSTMENT 6.1 Preparation Test Point CN102-pin 3 (MPX) CD test disc (TYPE 4 or STD-905) Discs to be Used Method FL Indication [Procedure] 1. Enter the Test mode. " FEOS_ _XX_ _ _ _ "...
CDR-205TX ADJUSTMENT PROCEDURES-6 6. SERVO ADJUSTMENT 6.4 Focus Bias Adjustment Test Point CN102-pin 2 (RF) Adjustment Value Minimize jitter value Optimizing DC offset voltage of focus servo loop circuit including pickup. Purpose Focus-in does not function, sound pauses, bad RF wave shape, or incapable to Symptom when Out of Adjustment playback some discs.
Page 36
CDR-205TX ADJUSTMENT PROCEDURES-7 7. Pickup replacement repair, the final check inspection method after adjustment Disc required: CD-R disc Standard disc for consumer (For music use). RDD-74 (PIONEER VIDEO CORP.) CD-RW disc Standard disc for consumer (For music use). RDW-74J (PIONEER VIDEO CORP.) [Inspection items] 1.
ERROR CODE Error Code Display for Service. The CDR-205TX/DX-R700 can display the error codes for service. 1. While pushing the YES key and FINALIZE key, press the DISPLAY key. 2. Turn the JOG(AMCS) key so that "S. Err Disp?" appears on the FL display.
CDR-205TX GENERAL INFORMATION-2 Error code table for service Code Generation Condition In the tray opening procedure, if opening action is not completed within 4.5 sec., the procedure moves to closing action. Afterwards if this closing action is not completed within 4.5 sec., the procedure recalls opening action again.
CDR-205TX PACKING VIEW PARTS LIST REF. NO PART NO. DESCRIPTION REF. NO PART NO. DESCRIPTION 24140448 Remote controller, RC-448C 29091978 Pad AS 3010054 Battery, UM-3 29053715 Carton 2050064 or NCS-1P106 29362818 Label EAN 2050072 NOP-1P50, Optical cable 29100037-1A Polybag, 650x500...