Table of Contents
Advertisement
Quick Links
Allo E1/T1 PRI Card Quick Installation Guide
Copyright
Copyright © 2015 Allo. All rights reserved.
No part of this publication may be copied, distributed, transmitted, transcribed, stored in a
retrieval system, or translated into any human or computer language without the prior written
permission of Allo.com. This document has been prepared for use by professional and properly
trained personnel, and the customer assumes full responsibility when using it.
Proprietary Rights
The information in this document is Confidential to Allo and is legally privileged. The information
and this document are intended solely for the addressee. Use of this document by anyone else for
any other purpose is unauthorized. If you are not the intended recipient, any disclosure, copying,
or distribution of this information is prohibited and unlawful.
Disclaimer
Allo E1/T1 PRI card
Information in this document is subject to change without notice and should not be construed as a
commitment on the part of allo.com. And does not assume any responsibility or make any
Installation Guide
warranty against errors. It may appear in this document and disclaims any implied warranty of
merchantability or fitness for a particular purpose.
www.allo.com
Version 2.1
1
Advertisement
Table of Contents
Summary of Contents for Allo.com 4aCP1e
- Page 1 Allo E1/T1 PRI card Information in this document is subject to change without notice and should not be construed as a commitment on the part of allo.com. And does not assume any responsibility or make any Installation Guide warranty against errors. It may appear in this document and disclaims any implied warranty of merchantability or fitness for a particular purpose.
- Page 2 Text in paragraphs without numbering represents ordinary information. The Courier font indicates a command sequence, file type, URL, Folder/File name e.g. www.allo.com Support Information Every effort has been made to ensure the accuracy of the document. If you have comments, questions, or ideas regarding the document contact online support: http://support.allo.com...
-
Page 3: Table Of Contents
3.1 Installation of Dahdi Driver ................... 9 3.2 Installation of LibPRI package ..................10 3.3 Installation of Asterisk ....................11 4. Software Configurations ....................11 4.1 T1 mode settings ......................11 4.2 Dahdi Configuration ....................11 Allo Support Information: ......................13 www.allo.com Version 2.1... -
Page 4: Introduction
, Elastix, Trixbox, as well as other open source and proprietary PBX, Switch, IVR, or VoIP gateway applications. Model No Product Description 4aCP1e/4aCP2e/4aCP4e/4aCP8e 1/2/4/8 Port PRI PCIe card 4aCP1eL/4aCP2eL/4aCP4eL/4aCP8eL 1/2/4/8 Port PRI PCIe card with Line Echo Cancellation 1.1 Overview Allo digital cards allow users to field upgrade the firmware based on their requirements. -
Page 5: Y- Splitter
The Y-splitter is provided for accessing all four ports on the Allo digital series cards. The following figure helps to identify a splitter and its end ports. Port A Port B Splitter End 1.3 Connection Diagram 4 Port-Connection Diagram www.allo.com Version 2.1... -
Page 6: Slot Compatibility
Check your motherboard to verify that a compatible slot is available for an Allo digital E1/T1 card. To determine which slots you have on your motherboard. Motherboard slots The Digital E1/T1 cards work with PCIe slot like x1, x2, x4, x8 and x16. www.allo.com Version 2.1... -
Page 7: Pri Card Led Indications
3. Take away the section place holder and addition the card into a PCI Express Slot. Insert Card 4. Plug the T1 or E1 equipment cable into the RJ45 port. Use only shield cables to ensure compliance with the international EMC standards. www.allo.com Version 2.1... -
Page 8: Hardware Setup
3. If the card is recognized, the following output will be displayed. Please search for Allo ID (1d21). # lspci Below Table lists the device ID and the number of ports supported. Device Id Model Number Card Type 1410 4aCP1e 1 port PRI Card 1420 4aCP2e 2 port PRI Card 1440 4aCP4e... -
Page 9: Software Installation Steps
Download latest ALLO Dahdi Drivers from Allo web site and install the Dahdi version as per your requirement. Please find the link here for download http://www.allo.com/3rd-GEN-1-2-4-8-Port- PRI-Card/ in that Guides & Drivers to get the dahdi driver by executing the following command. -
Page 10: Installation Of Libpri Package
#wget http://downloads.asterisk.org/pub/telephony/libpri/libpri-1.4.14.tar.gz After downloading LibPRI extract the LibPRI tar file by the following command [root@localhost src]# tar -xvzf libpri-1.4.14.tar.gz Install the LibPRI by the following commands [root@localhost src]# cd libpri-1.4.14 # make clean # make # make install www.allo.com Version 2.1... -
Page 11: Installation Of Asterisk
4.1 T1 mode settings To configure the card in T1 signaling mode, please add the following, (i) Add “options alloPL4xxp default_linemode=t1”at the end of /etc/modprobe.d/dahdi.conf 4.2 Dahdi Configuration After Dahdi driver installation run the following commands # /etc/init.d/dahdi start www.allo.com Version 2.1... - Page 12 Check alloPL4xxp show with + symbol “+ shows module loaded “ Start the Asterisk by executing # asterisk -gvvvvvvvvvc Make sure that PRI spans are up and active, before making calls. Here is the command to check the PRI span status CLI>pri show spans www.allo.com Version 2.1...
-
Page 13: Allo Support Information
7.30 PM (GMT+5.30) Indian standard time. Support will be available for Saturday based on request & prior schedule Support ticket is mandatory for all support sessions and prior schedule Submit support ticket on: http://support.allo.com/Tickets/New Customer knowledge base http://support.allo.com/KB www.allo.com Version 2.1... - Page 14 Allo E1/T1 PRI Card Quick Installation Guide www.allo.com Version 2.1...
Need help?
Do you have a question about the 4aCP1e and is the answer not in the manual?
Questions and answers